6R9126 GREASE NIPPLE Caterpillar parts
RT50
Rating:
Alternative (cross code) number:
CA6R9126
6R-9126
6R9126
CA6R9126
6R-9126
6R9126
Weight: 0.01 pounds 0 kg.
TELEHANDLER,
Compatible equipment models: 6R9126:
Number on catalog scheme:
5
For full view, you need register
Information:
Removal Procedure
Start By:
Connect the steering frame lock.
Release the hydraulic system pressure.
Pressurized System!Hydraulic accumulators contain gas and oil under high pressure. DO NOT disconnect lines or disassemble any component of a pressurized accumulator. All gas pre-charge must be removed from the accumulator as instructed by the service manual before servicing or disposing of the accumulator or any accumulator component.Failure to follow the instructions and warnings could result in personal injury or death.Only use dry nitrogen gas to recharge accumulators. See your Cat dealer for special equipment and detailed information for accumulator service and charging.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Drain the implement hydraulic system. Refer to the Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
Relieve the pressure from the ride control accumulator.
Illustration 1 g06128947
Disconnect hoses assembly (2) and remove manifold (1).
Illustration 2 g06128955
Use two people and a suitable jack to remove accumulator (4). The weight of accumulator (4) is approximately 50 kg (110lb). Remove bolts (3) and accumulator (4).
Illustration 3 g06128964
Use two people to remove accumulator (6). The weight of accumulator (6) is approximately 36 kg (79 lb). Remove bolts (5) and accumulator (6).Installation Procedure
Install accumulators (6) and (4) in the reverse order of removal.
Fill the implement hydraulic system. Refer to the Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
Start By:
Connect the steering frame lock.
Release the hydraulic system pressure.
Pressurized System!Hydraulic accumulators contain gas and oil under high pressure. DO NOT disconnect lines or disassemble any component of a pressurized accumulator. All gas pre-charge must be removed from the accumulator as instructed by the service manual before servicing or disposing of the accumulator or any accumulator component.Failure to follow the instructions and warnings could result in personal injury or death.Only use dry nitrogen gas to recharge accumulators. See your Cat dealer for special equipment and detailed information for accumulator service and charging.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Drain the implement hydraulic system. Refer to the Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
Relieve the pressure from the ride control accumulator.
Illustration 1 g06128947
Disconnect hoses assembly (2) and remove manifold (1).
Illustration 2 g06128955
Use two people and a suitable jack to remove accumulator (4). The weight of accumulator (4) is approximately 50 kg (110lb). Remove bolts (3) and accumulator (4).
Illustration 3 g06128964
Use two people to remove accumulator (6). The weight of accumulator (6) is approximately 36 kg (79 lb). Remove bolts (5) and accumulator (6).Installation Procedure
Install accumulators (6) and (4) in the reverse order of removal.
Fill the implement hydraulic system. Refer to the Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
Caterpillar parts catalog:
Parts grease Caterpillar catalog:
RT100, RT50
120, 120B, 12E, 12F, 140, 140B, 14E, 312, 328D LCR, 3408, 345B II, 345C, 5130, 650B, 666, 666B, 955C, 992, 992C, AP-1000, AP-1050, AP-1055D, AP-650B, AP-800C, AP-800D, AS2251, AS2301, BG-225B, BG-225C...
RT100, RT50
1C8141
GREASE GUN AS
966C
966C
1483352
GREASE LINES
307B
307B
1531468
GREASE LINES
307B
307B
1373254
GREASE LINES
311B, 311C
311B, 311C
3Y7597
GREASE (FOR WINTER TIME)
307, 307B, 311, 315, 320 L, 320C, 325, 325C, 375
307, 307B, 311, 315, 320 L, 320C, 325, 325C, 375
4Y0426
GREASE (BELLOWS)
307, 307B, 311, 315, 320 L, 320C, 325, 325C, 375
307, 307B, 311, 315, 320 L, 320C, 325, 325C, 375
2537115
GREASE GUN AS
M313D, M315D, M316D, M318D, M318D MH, M322D, M322D MH
M313D, M315D, M316D, M318D, M318D MH, M322D, M322D MH
1P0808
GREASE-MULTIPURPOSE
307, 307B, 311, 3126B, 315, 320 L, 320C, 325, 325C, 3456, 3516B, 375, 651B, 966F II, 970F, C-15, C-16, C15, C18, CX31-C15I, CX35-P800, M318, M320, SR4, TH35-C15I
307, 307B, 311, 3126B, 315, 320 L, 320C, 325, 325C, 3456, 3516B, 375, 651B, 966F II, 970F, C-15, C-16, C15, C18, CX31-C15I, CX35-P800, M318, M320, SR4, TH35-C15I
120M 2, 3408, 3508, 3508B, 3512, 3512B, 3516, 3516B, 3516C, 735B, 740B, 785C, 785D, 854K, 950H, 950K, 962K, 966K, 972K, 980H, 980K, 980K HLG, 986H, 988H, 992K, 993K, 994H, C15, C18, C27, C32, D6R III,...
120, 120B, 12E, 12F, 140, 140B, 14E, 312, 328D LCR, 3408, 345B II, 345C, 5130, 650B, 666, 666B, 955C, 992, 992C, AP-1000, AP-1050, AP-1055D, AP-650B, AP-800C, AP-800D, AS2251, AS2301, BG-225B, BG-225C...