4I3097 GROMMET Caterpillar parts
307, 307B, 311B, 318B, 320, 320 L, 320B, 325, 325 L, 325 LN, 325B, 330, 330 L, 345B II, 350, 365B, 365B L, 385B
Rating:
Alternative (cross code) number:
CA4I3097
4I-3097
4I3097
CA4I3097
4I-3097
4I3097
Weight: 0.02 pounds 0 kg.
EXCAVATOR, MINI HYD EXCAVATOR,
Compatible equipment models: 4I3097:
Number on catalog scheme:
13
For full view, you need register
Information:
Rigging-Moving Jaw Safety
When working in or near the jaw, a safety rigging must be installed to ensure that there is no unintended motion of the moving jaw. Apply rigging with at least 2500 kg (5500 lb) capacity between the moving jaw maintenance eye and rear housing lifting eye (moving jaw safety rigging).
Illustration 1 g06119307Jaw Hub Side Play-Inspect
Open the jaws of the shear, and place the shear heel on the ground.
Turn off the engine and relieve hydraulic pressure.
Do not operate the work tool unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in machine or work tool damage, serious injury or death.
Personal injury or death can result from sudden work tool movement.Sudden movement of the work tool can cause injury to persons near the work tool.To prevent injury or death, make sure that the area around the work tool is clear of personnel and obstructions before operating the work tool.
Apply moving jaw safety rigging. Refer to Operation and Maintenance Manual, "Rigging-Moving jaw safety".
Illustration 2 g06108645
Place a prybar between the moving jaw and the inside of the housing on the cutting side, and push the moving jaw toward the drop side. Look for motion between the jaw and hub.
Illustration 3 g06108646
Place a prybar between the moving jaw and the inside of the housing on the drop side, and push the moving jaw toward the cutting side. Look for motion between the jaw and hub.
If any visible movement is seen between the moving jaw and hub, the hub needs to be tightened.Jaw Hub Side Play-Tighten
Illustration 4 g06116771
Remove the hub cover on the drop side of the hub.
Illustration 5 g06318759
Loosen the two bolts on the locking plate of the hub pin 2-3 full turns such that the bolt heads protrude above the surface.
Reinstall the hub cover. Tighten the 4-bolts evenly, allowing it to push on the locking plate bolt heads, which pushes the hub pin toward the cutting side. Do not exceed 240 N m (177 lb ft) while tightening the 4 bolts.
Illustration 6 g06117925
Remove the two locking bolts in the hub nut. Tighten the hub nut with a 1 inch drive to 700 75 N m (516 55 lb ft), then turn clockwise to align the next bolt hole and reinstall the two locking bolts. Tighten the two locking bolts to 240 40 N m (177 30 lb ft)
Illustration 7 g06118836
(1) Locking Bolts
(2) Hub Nut
Remove the hub cover.
Tighten the two bolts on the locking plate of the hub pin to 460 60 N m (340 44 lb ft).
Reinstall the hub cover and tighten to 240 40 N m (177 30 lb ft)
Perform the blade rotation / replacement and piercing tip replacement.
When working in or near the jaw, a safety rigging must be installed to ensure that there is no unintended motion of the moving jaw. Apply rigging with at least 2500 kg (5500 lb) capacity between the moving jaw maintenance eye and rear housing lifting eye (moving jaw safety rigging).
Illustration 1 g06119307Jaw Hub Side Play-Inspect
Open the jaws of the shear, and place the shear heel on the ground.
Turn off the engine and relieve hydraulic pressure.
Do not operate the work tool unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in machine or work tool damage, serious injury or death.
Personal injury or death can result from sudden work tool movement.Sudden movement of the work tool can cause injury to persons near the work tool.To prevent injury or death, make sure that the area around the work tool is clear of personnel and obstructions before operating the work tool.
Apply moving jaw safety rigging. Refer to Operation and Maintenance Manual, "Rigging-Moving jaw safety".
Illustration 2 g06108645
Place a prybar between the moving jaw and the inside of the housing on the cutting side, and push the moving jaw toward the drop side. Look for motion between the jaw and hub.
Illustration 3 g06108646
Place a prybar between the moving jaw and the inside of the housing on the drop side, and push the moving jaw toward the cutting side. Look for motion between the jaw and hub.
If any visible movement is seen between the moving jaw and hub, the hub needs to be tightened.Jaw Hub Side Play-Tighten
Illustration 4 g06116771
Remove the hub cover on the drop side of the hub.
Illustration 5 g06318759
Loosen the two bolts on the locking plate of the hub pin 2-3 full turns such that the bolt heads protrude above the surface.
Reinstall the hub cover. Tighten the 4-bolts evenly, allowing it to push on the locking plate bolt heads, which pushes the hub pin toward the cutting side. Do not exceed 240 N m (177 lb ft) while tightening the 4 bolts.
Illustration 6 g06117925
Remove the two locking bolts in the hub nut. Tighten the hub nut with a 1 inch drive to 700 75 N m (516 55 lb ft), then turn clockwise to align the next bolt hole and reinstall the two locking bolts. Tighten the two locking bolts to 240 40 N m (177 30 lb ft)
Illustration 7 g06118836
(1) Locking Bolts
(2) Hub Nut
Remove the hub cover.
Tighten the two bolts on the locking plate of the hub pin to 460 60 N m (340 44 lb ft).
Reinstall the hub cover and tighten to 240 40 N m (177 30 lb ft)
Perform the blade rotation / replacement and piercing tip replacement.
Caterpillar parts catalog:
Parts grommet Caterpillar catalog:
115, 215B, 215C, 215D, 225, 227, 242B, 242B3, 245B, 247B, 24H, 257B, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 287C, 287C2, 289C, 289C2, 297C, 299C, 311B, 311C, 311D LRR, 311F LRR, 312B, 312C, 312D...
115, 1190, 1190T, 120M, 1290T, 12M, 12M 3, 12M 3 AWD, 1390, 140M, 140M 3, 140M 3 AWD, 14M, 160M, 160M 3, 160M 3 AWD, 215, 215B, 215C, 215D, 219D, 225, 225D, 227, 229, 2290, 231D, 235D, 236D, 2384C, 23...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 235B, 245, 24H, 24M, 272D XHP, 299D XHP, 303...
120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H, 16M, 225, 227, 24H, 24M, 303, 303.5E, 303E CR, 3...
120G, 120H ES, 120H NA, 12G, 12H NA, 130G, 135H NA, 140G, 140H NA, 143H, 14G, 160H NA, 163H NA, 16G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 229D, 231D, 235, 235B, 235C, 235D, 245, 245B, 245D, 312...
320 L, 345C MH, 350 L, 3508B, 3512B, 3512C, 3516B, 3516C, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 446, 446B, 446D, 5110B, ...
1390, 216, 216B, 216B3, 226B, 226B3, 227, 228, 232B, 235D, 236, 236B, 236B3, 236D, 2384C, 242B, 242B3, 242D, 245, 245B, 245D, 246C, 246D, 247, 247B, 247B3, 2484C, 252B, 252B3, 256C, 257B, 257B3, 257D,...
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 583T, 587T, 621B, 621F, 621G, 621H, 623E, 623F, 623G, 623H, 627F, 627G, ...
16M, 2470C, 24H, 24M, 2570C, 2670C, 2864C, 307B, 307C, 308D, 308E, 308E2 CR, 312C, 316E L, 318E L, 320B FM LL, 320C, 322 FM L, 330D L, 336D L, 336E HVG, 345C L, 349E L HVG, 385B, 390D, 390D L, 416E, 4...
7Y7364
GROMMET
307, 307B, 307C, 307D, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315, 315C, 315D L, 318B, 318C, 318D L, 318D2 L, 319D L, 3...
307, 307B, 307C, 307D, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315, 315C, 315D L, 318B, 318C, 318D L, 318D2 L, 319D L, 3...
4I3096
GROMMET
307, 307B, 311, 311B, 312B, 315, 318B, 320 L, 320B, 320N, 322 FM L, 322B L, 325, 325 L, 325 LN, 325B, 330, 330 FM L, 330 L, 345B II, 345B L, 350, 365B, 365B L, 385B
307, 307B, 311, 311B, 312B, 315, 318B, 320 L, 320B, 320N, 322 FM L, 322B L, 325, 325 L, 325 LN, 325B, 330, 330 FM L, 330 L, 345B II, 345B L, 350, 365B, 365B L, 385B
0878484
GROMMET
303, 304, 305, 307, 307B, 307E, 308C, 308D, 308E, 308E2 CR, 311, 311B, 312B, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 318B, 320 L, 320B, 320N, 321C, 321D LCR, 322 FM L, 322B L, 325, 325 L, 325...
303, 304, 305, 307, 307B, 307E, 308C, 308D, 308E, 308E2 CR, 311, 311B, 312B, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 318B, 320 L, 320B, 320N, 321C, 321D LCR, 322 FM L, 322B L, 325, 325 L, 325...
1474819
GROMMET
311B, 312B, 312C, 312C L, 315C, 318B, 318C, 319C, 320B, 320C, 320C FM, 320C L, 322C, 325B, 325C, 330C, 330C L, 345B II, 365B, 365B L, 385B
311B, 312B, 312C, 312C L, 315C, 318B, 318C, 319C, 320B, 320C, 320C FM, 320C L, 322C, 325B, 325C, 330C, 330C L, 345B II, 365B, 365B L, 385B
303, 304, 305, 312D, 312D L, 312E, 312E L, 314E CR, 314E LCR, 315D L, 316E L, 318B, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D LN, 323D SA...
1315380
GROMMET-BLIND
307B, D5M, D5N, D6M, D6N
307B, D5M, D5N, D6M, D6N
1176307
GROMMET
307B, 311B, 312B, 315B FM L, 318B, 320B, 320B FM LL, 325B, 345B II, 345B L, 365B, 365B L, 385B
307B, 311B, 312B, 315B FM L, 318B, 320B, 320B FM LL, 325B, 345B II, 345B L, 365B, 365B L, 385B
5I3827
GROMMET
311, 311B, 312B, 315, 315B, 315B FM L, 318B, 320 L, 320B, 320D L, 320N, 322, 322 FM L, 322 LN, 322B
311, 311B, 312B, 315, 315B, 315B FM L, 318B, 320 L, 320B, 320D L, 320N, 322, 322 FM L, 322 LN, 322B
1474855
GROMMET
311B, 312B, 312C L, 315C, 318B, 318C, 320C, 322C, 325B, 325C, 330C L
311B, 312B, 312C L, 315C, 318B, 318C, 320C, 322C, 325B, 325C, 330C L
1597783
GROMMET
311B, 318B, 325B, 345B II, 365B, 365B L, 385B
311B, 318B, 325B, 345B II, 365B, 365B L, 385B
0995307
GROMMET
303, 304, 305, 318B, 325B, 345B II, 725, 730, 735, 740, 980G, 980G II, 980H, RM-300
303, 304, 305, 318B, 325B, 345B II, 725, 730, 735, 740, 980G, 980G II, 980H, RM-300
4I4357
GROMMET
307, 307B, 311B, 318B, 320, 320 L, 320B, 325, 325 L, 325B, 330, 330 L, 345B II
307, 307B, 311B, 318B, 320, 320 L, 320B, 325, 325 L, 325B, 330, 330 L, 345B II