GROMMET 5H9743 - Caterpillar

Install assembled support bracket (44) to engine with 4x 8F-8544 Bolt (46), 0S-1619 Bolt (47), 5x 5M-2894 Hard Washer (20), 5P-8245 Hard Washer (21) and 1F-7958 Full Nut (18). Tighten the bolts to a torque of 47 9 N m (35 7 lb ft) and nut to a torque of 105 20 N m (77 15 lb ft).
Illustration 16 g06073845
(48) 350-0223 Belt Tensioner
(49) 8T-0644 Bolt
(50) 6V-5839 Washer
Install new 350-0223 Belt Tensioner (48) with 8T-0644 Bolt (49) and 6V-5839 Washer (50) to a torque of 55 10 N m (41 7 lb ft).
Illustration 17 g06075023
(51) 130-5300 Clip
(52) 306-8524 Bracket As
(53) 8T-4224 Hard Washer
(54) 8T-3647 Bolt
(55) 258-9892 Bolt
(56) 8T-4121 Hard Washer
(57) 8T-4137 Bolt
(58) 5P-7854 Clip
(59) 6D-4244 Clip
Install Compressor (1) with A/C Hose (4) and related parts. Refer to Illustration 17 for the part numbers. Tighten the 8T-3647 Bolt (54) and 258-9892 Bolt (55) to a torque of 28 7 N m (248 62 lb in).
Install bracket As (7) and related parts. Refer to Illustration 17 for the part numbers. Adjust the angle of 5P-7854 Clip (58) and 6D-4244 Clip (59) and tighten the 8T-4137 Bolt (57) to a torque of 55 10 N m (41 7 lb ft).
Illustration 18 g06073887
(60) 350-5812 Serpentine Belt
Install new 350-5812 Serpentine Belt (60). Refer to Illustration 18 for the routing.
Illustration 19 g06073890
(61) Cutout for terminal
Cut and remove 2x part (C) from alternator cover (10). Refer to the Illustration 19 for dimensions. Be careful for the direction. confirm the position of cutout (61).
Illustration 20 g06058457
Install Alternator cover (10) tighten bolts to 2.25 0.25 N m (19.914 2.213 lb in). Install Air hose (8) and clamps (9) to a torque of 11 1 N m (97 9 lb in).
Illustration 21 g06059122
Maintain 10 to 15 mm (0.4 to 0.6 inch) clearance at (D) between A/C hose (4) and Air hose (8).
Illustration 22 g06073940
If there is not enough clearance (D), adjust the angle of clip (58) and A/C hose (4) routing to make required clearance.
Illustration 23 g06073904
(62) 111-4836 Clip
(63) 111-4837 Clip
(64) R Terminal
(65) B (-) Terminal
(66) B (+) Terminal
Connect harness assemblies (2) and install related parts as same as before. Refer to the Illustration 23 for the part numbers. Tighten 8T-4137 Bolt (57) to a torque of 55 10 N m (41 7 lb ft).
Tighten B (-) terminal (65) to a torque of 4.4 1.0 N m (39.0 8.8 lb in) and B (+) terminal (66) to a torque of 18.2 2.4 N m (161.1 21.2 lb in).