8T7088 GROMMET Caterpillar parts
2864C, 345C MH, 345D L, 349D L, 3608, 375, 375 L, 5110B, 5130, 5130B, 535C, 545C, 586C, 657E, 730C, 777G, 910G, 966H, 972H, D6H, D6H XL, D6H XR, D7E, D7E LGP, M325D L MH
Rating:
Alternative (cross code) number:
CA8T7088
8T-7088
8T7088
CA8T7088
8T-7088
8T7088
Weight: 0.70 pounds 0 kg.
Information:
CENTERLINE OF TO CENTERLINE OF
44
mm
LARGE/SAME ID
34
mm
RADIUS
26
mm
SMALL ID
34
mm
WIDTH
71.5
mm
ARTICULATED TRUCK, WHEEL SKIDDER,
Compatible equipment models: 8T7088:
Number on catalog scheme:
7
For full view, you need register
Information:
This diagnostic code is recorded when VIMS electronic control module reads the signal from the trailer brake oil cooler outlet temperature sensor and the frequency of the signal or pulse of the signal is not within an expected range. The sensor sends a PWM signal to the VIMS electronic control module. The possible causes of this diagnostic code are listed here:
The sensor has failed.
Intermittent connections or poor connections
The VIMS electronic control module has failed. This is unlikely.Note: The following diagnostic code procedure can create other related diagnostic codes. Perform the following procedure. Reconnect all harnesses. Then clear all the related diagnostic codes.Test Step 1. CHECK THE SENSOR.
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Disconnect the sensor from the machine harness. Expected Result:The diagnostic code has changed from CID 0657 FMI 08 to CID 0657 FMI 03.Results:
YES - The diagnostic code has changed from CID 0657 FMI 08 to CID 0657 FMI 03. The sensor has failed.Repair: Replace the sensor. Verify that the new sensor corrected this diagnostic code. The diagnostic code should NOT be active.STOP
NO - The diagnostic code CID 0657 FMI 08 remains active. The sensor is not the cause of the diagnostic code. proceed to test step 2.Test Step 2. CHECK FOR A SHORT IN THE MACHINE HARNESS.
The sensor remains disconnected from the machine harness.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 and J2 machine harness connectors from the VIMS electronic control module.
At the machine harness connector for the VIMS electronic control module, measure the resistance between the signal contact to all other J1 and J2 contacts. Expected Result:Each resistance measurement should be greater than 5000 ohms.Results:
YES - Each resistance measurement is greater than 5000 ohms. The harness is correct. The VIMS electronic control module has failed.Repair: It is unlikely that the VIMS electronic control module has failed. Exit this procedure and perform this diagnostic code procedure again. If the cause of the diagnostic code is not found, replace the VIMS electronic control module. Refer to the Testing and Adjusting, " Module - Replace" section. STOP
NO - The resistance is not greater than 5000 ohms for each measurement. The machine harness has failed. There is a short in the machine harness. The short is between the signal circuit and the circuit with the low resistance measurement. Repair: Repair the machine harness or replace the machine harness.STOP
The sensor has failed.
Intermittent connections or poor connections
The VIMS electronic control module has failed. This is unlikely.Note: The following diagnostic code procedure can create other related diagnostic codes. Perform the following procedure. Reconnect all harnesses. Then clear all the related diagnostic codes.Test Step 1. CHECK THE SENSOR.
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Disconnect the sensor from the machine harness. Expected Result:The diagnostic code has changed from CID 0657 FMI 08 to CID 0657 FMI 03.Results:
YES - The diagnostic code has changed from CID 0657 FMI 08 to CID 0657 FMI 03. The sensor has failed.Repair: Replace the sensor. Verify that the new sensor corrected this diagnostic code. The diagnostic code should NOT be active.STOP
NO - The diagnostic code CID 0657 FMI 08 remains active. The sensor is not the cause of the diagnostic code. proceed to test step 2.Test Step 2. CHECK FOR A SHORT IN THE MACHINE HARNESS.
The sensor remains disconnected from the machine harness.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 and J2 machine harness connectors from the VIMS electronic control module.
At the machine harness connector for the VIMS electronic control module, measure the resistance between the signal contact to all other J1 and J2 contacts. Expected Result:Each resistance measurement should be greater than 5000 ohms.Results:
YES - Each resistance measurement is greater than 5000 ohms. The harness is correct. The VIMS electronic control module has failed.Repair: It is unlikely that the VIMS electronic control module has failed. Exit this procedure and perform this diagnostic code procedure again. If the cause of the diagnostic code is not found, replace the VIMS electronic control module. Refer to the Testing and Adjusting, " Module - Replace" section. STOP
NO - The resistance is not greater than 5000 ohms for each measurement. The machine harness has failed. There is a short in the machine harness. The short is between the signal circuit and the circuit with the low resistance measurement. Repair: Repair the machine harness or replace the machine harness.STOP
Cat SIS web machinery list:
Parts grommet Caterpillar catalog:
12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 2290, 236B3, 236D, 2390, 2391, 242D, 246D, 2491, 24M, 252B3, 257B3, 257D, 2590, 259B3, 259D, 262D, 272D, 272D XHP, 277D...
1390, 216, 216B, 216B3, 226B, 226B3, 227, 228, 232B, 235D, 236, 236B, 236B3, 236D, 2384C, 242B, 242B3, 242D, 245, 245B, 245D, 246C, 246D, 247, 247B, 247B3, 2484C, 252B, 252B3, 256C, 257B, 257B3, 257D,...
216, 227, 236, 246C, 24H, 256C, 262C, 262C2, 262D, 272C, 272D, 272D XHP, 277C, 277C2, 279C, 279C2, 287C, 287C2, 287D, 289C, 289C2, 289D, 297C, 299C, 299D, 299D XHP, 325D FM, 325D FM LL, 330D FM, 375, ...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 236, 236B, 236B3, 2390, 2391, 245D, 246C, 248, 2491, 24M, 252B, 252B3, 2...
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 583T, 587T, 621B, 621F, 621G, 621H, 623E, 623F, 623G, 623H, 627F, 627G, ...
120M, 120M 2, 12M, 12M 2, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 24M, 311D LRR, 312D, 312D L, 312E, 312E L, 314E CR, 314E LCR, 315D L, 316E L, 318E L, 319D L, 319D LN, 320E, 320E L, 320E LN, 320E LRR, ...
16M, 2470C, 24H, 24M, 2570C, 2670C, 2864C, 307B, 307C, 308D, 308E, 308E2 CR, 312C, 316E L, 318E L, 320B FM LL, 320C, 322 FM L, 330D L, 336D L, 336E HVG, 345C L, 349E L HVG, 385B, 390D, 390D L, 416E, 4...
24H, 330D MH, 345C, 345C MH, 3508B, 3512B, 3516B, 365C, 365C L, 365C L MH, 374D L, 375, 416E, 420E, 430E, 432E, 434E, 5080, 5110B, 5130, 5130B, 5230, 5230B, 525C, 535C, 545C, 589, 735, 735B, 740, 740B...
2864C, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 39...
120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 225, 24H, 24M, 320D, 320D FM RR, 320D LRR, 320D RR, 322 FM L, 323D L, 323D LN, 323D SA, 3...
572R, 572R II, 578, 583R, 583T, 587R, 587T, D11T, D6G2 LGP, D6G2 XL, D6H, D6H II, D6H XL, D6H XR, D6R, D7G, D7G2, D7H, D7R, D7R II, D7R XR, D8N, D8R, PL83, PL87, R2900
621E, 621F, 621G, 621H, 621K, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 69D, 769C, 769D, 770, 771C, 771D, 772, ...
115, 14M, 235B, 245, 24H, 24M, 2864C, 315, 316E L, 317, 318E L, 3208, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D L, 320D2 L, 320E, 320E L, 320E LN, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E L,...
6K5182
GROMMET
3606, 3608, 814, 815, 816, 941, 950, 966C, 980B, 980C, C280-6, C280-8, D5
3606, 3608, 814, 815, 816, 941, 950, 966C, 980B, 980C, C280-6, C280-8, D5
1030892
GROMMET
3512, 3512B, 3512C, 3516B, 3516C, 3618, 5130, 5130B, 5230, 5230B, 725, 730, 769D, 771D, 773D, 773E, 773F, 775E, 775F, 776C, 776D, 777, 777B, 777C, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789, 7...
3512, 3512B, 3512C, 3516B, 3516C, 3618, 5130, 5130B, 5230, 5230B, 725, 730, 769D, 771D, 773D, 773E, 773F, 775E, 775F, 776C, 776D, 777, 777B, 777C, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789, 7...
2311351
GROMMET
C1.5, C2.2, C4.4
C1.5, C2.2, C4.4
2311350
GROMMET
C1.5, C2.2, C4.4
C1.5, C2.2, C4.4
2311349
GROMMET
C1.5, C2.2
C1.5, C2.2
2734715
GROMMET
C4.4
C4.4
3009750
GROMMET
C4.4
C4.4
2656534
GROMMET
C4.4, C6.6, C7.1
C4.4, C6.6, C7.1
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16H NA, 16M, 2384C, 2484C, 24M, 303.5C, 303.5D, 303.5E, 303C CR, 304C CR...
2757901
GROMMET
3508B, 3508C, 3512B, 3512C, 3516B, 3516C, 793D
3508B, 3508C, 3512B, 3512C, 3516B, 3516C, 793D
120K, 120K 2, 12K, 12M, 140G, 140K, 140K 2, 140M, 160K, 3116, 3126, 3126B, 3126E, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L...