1530702 GUARD Caterpillar parts
924F, 924G, 924GZ, 924H, 924HZ
Rating:
Alternative (cross code) number:
CA1530702
153-0702
1530702
CA1530702
153-0702
1530702
Weight: 0.65 pounds 0 kg.
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
HELLA 6PU 230 048-111 Sensor, wheel speed - 2-pin connector - Front Axle
HELLA HELLA ABS Sensor /Fitting Side = Front Axle || This replacement corresponds to the original part in terms of performance. The quality of the replacement part fully meets the requirements set by car manufacturers. || Wheel Sensor, ABS Wheel Sensor, Wheel Speed Sensor, Wheel Turn Sensor, Number of Wheel Sensor: for 4 - series 94 L/260, for 4 - series 94 L/260, for 4 - series 94 G/260, for 4 - series 94 G. 260 cm || OE Code: 1428454, 1530702, 1545506, 1892056 || Choose your vehicle in the selector to verify its compatibility with the product.
HELLA HELLA ABS Sensor /Fitting Side = Front Axle || This replacement corresponds to the original part in terms of performance. The quality of the replacement part fully meets the requirements set by car manufacturers. || Wheel Sensor, ABS Wheel Sensor, Wheel Speed Sensor, Wheel Turn Sensor, Number of Wheel Sensor: for 4 - series 94 L/260, for 4 - series 94 L/260, for 4 - series 94 G/260, for 4 - series 94 G. 260 cm || OE Code: 1428454, 1530702, 1545506, 1892056 || Choose your vehicle in the selector to verify its compatibility with the product.
$58.01
25 Mar 2024
0.36[0.16] Pounds
PL: LeWron
DT Spare Parts EBS Sensor 1.21628 L: 2060 mm Sensor for Truck
DT Spare Parts Please note: Please check whether the item really fits your vehicle. Use the data from your vehicle documents. Please also note additional restrictions in the Amazon vehicle finder! || Product information: sensor, speed; weight [g]: 162; warranty: 2 year warranty; length [mm]: 2.060; box contents: 1 piece; condition: new || OE comparison numbers: 1428454, 1530702, 1545506, 1892056, 530702 || Note: You need help with your car part? Use our free verification service to avoid incorrect orders. Please select your vehicle from the Amazon vehicle list.
DT Spare Parts Please note: Please check whether the item really fits your vehicle. Use the data from your vehicle documents. Please also note additional restrictions in the Amazon vehicle finder! || Product information: sensor, speed; weight [g]: 162; warranty: 2 year warranty; length [mm]: 2.060; box contents: 1 piece; condition: new || OE comparison numbers: 1428454, 1530702, 1545506, 1892056, 530702 || Note: You need help with your car part? Use our free verification service to avoid incorrect orders. Please select your vehicle from the Amazon vehicle list.
$186.99
08 Apr 2023
19.6[8.82] Pounds
Amazon.com
Rugged Ridge TREK 8 Wheel Gloss Black Painted Finish (17 x 8. inches /5 x 110 mm, 30 mm Offset)
Rugged Ridge Lightweight one-piece 17x8-inch cast 8-spoke aluminum wheel || Stunning gloss black finish for a clean look || Renegade specific hub-centric design with 5 on 110 bolt pattern and +30mm offset || Meets SAE J2530 standards || Includes center cap
Rugged Ridge Lightweight one-piece 17x8-inch cast 8-spoke aluminum wheel || Stunning gloss black finish for a clean look || Renegade specific hub-centric design with 5 on 110 bolt pattern and +30mm offset || Meets SAE J2530 standards || Includes center cap
Number on catalog scheme:
1
For full view, you need register
Information:
"Equipment ID"
The "Equipment ID" parameter allows the customer to enter a description into the ECM in order to identify the machine. A maximum of 17 characters can be entered in the field."Engine Serial Number"
The "Engine Serial Number" should be programmed to match the engine serial number that is stamped on the engine information plate. The engine serial number is not preprogrammed on a replacement ECM."FLS" (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information ratings plate. This value should only be changed if the engine is rerated or a new ECM is installed. Factory passwords are required."FTS" (Full Torque Setting)
"FTS" is similar to "FLS". This value should only be changed if the engine is rerated or a new ECM is installed. Factory passwords are required."Fuel Air Ratio Control Adjust" (FARC)
FARC is a fuel system adjustment that has been performed at the factory in order to fine tune the fuel system. The value that is assigned to the parameter is stamped on the Engine Information plate for each engine."Ether Control"
The "Ether Control" parameter allows the operation of this feature to be enabled or disabled."System Battery Voltage Low Elevated Idle"
The "System Battery Voltage Low Elevated Idle" parameter allows the ECM to increase the engine speed. The engine speed is increased when the ECM detects low battery voltage.Parameter Table
Table 1
Customer Specified Parameters
Parameter Available Range or Options Default Required Password
"Equipment ID" 17 characters blank none
"Engine Serial Number" 8 characters blank none
"FLS" -128 to +127 0 Factory
"FTS" -128 to +127 0 Factory
"Fuel Air Ratio Control Adjust" 100 to 250 100 none
"Ether Control" "Enabled"
"Disabled" "Enabled" none
"System Battery Voltage Low Elevated Idle" "Enabled"
"Disabled" "Enabled" none Parameter Worksheet
Record the following information before you change any programmable parameter.
Table 2
Information from ECM
"Equipment ID"
"Engine Serial Number"
"ECM Serial Number"
"Personality Module Part Number"
"Personality Module Release Date"
"Personality Module Description"
"FLS"
"FTS"
"Fuel Air Ratio Control Adjust"
"Ether Control"
"System Battery Voltage Low Elevated Idle"
"Total Tattletale"
Information From Engine Information Plate
Engine Serial Number
Fuel Air Ratio(for new ECM)
Full Load Setting (for new ECM)
Full Torque Setting (for new ECM)
Note: Compare the FLS and the FTS from the ECM with the values that are listed on the Engine Information Plate. The FLS and the FTS should only be changed because of a mechanical change in the
The "Equipment ID" parameter allows the customer to enter a description into the ECM in order to identify the machine. A maximum of 17 characters can be entered in the field."Engine Serial Number"
The "Engine Serial Number" should be programmed to match the engine serial number that is stamped on the engine information plate. The engine serial number is not preprogrammed on a replacement ECM."FLS" (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information ratings plate. This value should only be changed if the engine is rerated or a new ECM is installed. Factory passwords are required."FTS" (Full Torque Setting)
"FTS" is similar to "FLS". This value should only be changed if the engine is rerated or a new ECM is installed. Factory passwords are required."Fuel Air Ratio Control Adjust" (FARC)
FARC is a fuel system adjustment that has been performed at the factory in order to fine tune the fuel system. The value that is assigned to the parameter is stamped on the Engine Information plate for each engine."Ether Control"
The "Ether Control" parameter allows the operation of this feature to be enabled or disabled."System Battery Voltage Low Elevated Idle"
The "System Battery Voltage Low Elevated Idle" parameter allows the ECM to increase the engine speed. The engine speed is increased when the ECM detects low battery voltage.Parameter Table
Table 1
Customer Specified Parameters
Parameter Available Range or Options Default Required Password
"Equipment ID" 17 characters blank none
"Engine Serial Number" 8 characters blank none
"FLS" -128 to +127 0 Factory
"FTS" -128 to +127 0 Factory
"Fuel Air Ratio Control Adjust" 100 to 250 100 none
"Ether Control" "Enabled"
"Disabled" "Enabled" none
"System Battery Voltage Low Elevated Idle" "Enabled"
"Disabled" "Enabled" none Parameter Worksheet
Record the following information before you change any programmable parameter.
Table 2
Information from ECM
"Equipment ID"
"Engine Serial Number"
"ECM Serial Number"
"Personality Module Part Number"
"Personality Module Release Date"
"Personality Module Description"
"FLS"
"FTS"
"Fuel Air Ratio Control Adjust"
"Ether Control"
"System Battery Voltage Low Elevated Idle"
"Total Tattletale"
Information From Engine Information Plate
Engine Serial Number
Fuel Air Ratio(for new ECM)
Full Load Setting (for new ECM)
Full Torque Setting (for new ECM)
Note: Compare the FLS and the FTS from the ECM with the values that are listed on the Engine Information Plate. The FLS and the FTS should only be changed because of a mechanical change in the
Caterpillar parts catalog:
Parts guard Caterpillar catalog:
918F, 924F, 928F, 928G, IT18F, IT24F, IT28F, IT28G
2098713
GUARD AS
924G, 924GZ, 924H, 924HZ, 928HZ, 930G, IT28G
924G, 924GZ, 924H, 924HZ, 928HZ, 930G, IT28G
2511478
GUARD
906, 906H, 907H, 908, 908H, 924G, 924GZ, 930G, IT28G
906, 906H, 907H, 908, 908H, 924G, 924GZ, 930G, IT28G
2055467
GUARD-HOSE
924G, 924GZ
924G, 924GZ
2191460
GUARD-HOSE
924G, 924GZ
924G, 924GZ
3101917
GUARD AS
924H, 924HZ, 928HZ, 930G
924H, 924HZ, 928HZ, 930G
2768435
GUARD-ALTERNATOR
924H, 924HZ, 928HZ
924H, 924HZ, 928HZ
3027844
GUARD
924H, 924HZ, 928HZ
924H, 924HZ, 928HZ
924H, 924HZ, 928H, 928HZ
3574944
GUARD AS
924H, 924HZ, 928HZ
924H, 924HZ, 928HZ
2950580
GUARD AS
924H, 924HZ, 928HZ
924H, 924HZ, 928HZ
3591937
GUARD AS
924H, 928HZ
924H, 928HZ
938F, 938G, 938G II, 938H, IT38G
1146385
GUARD AS
938F, IT38F, IT38G
938F, IT38F, IT38G
1096505
GUARD-BUCKET
938F, 966F II, 970F
938F, 966F II, 970F
1221842
GUARD AS
938F, IT38F, IT38G
938F, IT38F, IT38G
1221841
GUARD AS
938F, IT38F, IT38G
938F, IT38F, IT38G
1226707
GUARD AS-FAN
914G, IT14G
914G, IT14G
1226495
GUARD AS
928G, IT28G
928G, IT28G
2005212
GUARD AS
928G, IT28G
928G, IT28G
1226268
GUARD-HOSE
928G, 928HZ, IT28G
928G, 928HZ, IT28G
2045357
GUARD AS
928G, IT28G
928G, IT28G
1133670
GUARD AS
928G, IT28G
928G, IT28G
1133620
GUARD AS-FAN HOUSING
928G, IT28G
928G, IT28G