GUARD AS-TRACK GUIDE 2198469 - Caterpillar

Agricultural Tractor AllArticulated Truck AllAsphalt Paver AllChallenger AllCold Planer AllCombine AllExcavator5130 (S/N: 7TJ1-UP; 5ZL1-UP)Forest Products AllIntegrated Toolcarrier AllLandfill Compactor AllMachine Engines 3054 3056 3304 3306 3406B 3406C 3408E 3412EMachine Engines with Mechanical Unit Injection 3500 SeriesMotor Grader AllOff-Highway Truck/Tractor773 (S/N: 63G1-UP)773B (S/N: 63W1-UP)777 (S/N: 84A1-UP)777B (S/N: 4YC1-UP)Paving Compactor AllPipelayer AllRoad Reclaimer/Soil Stabilizer AllSoil Compactor AllTrack-Type Loader AllTrack-Type Skidder AllTrack-Type Tractor AllWheel Dozer AllWheel Loader AllWheel Skidder AllWheel Tractor-Scraper AllIntroduction
This Special Instruction contains assembly information for the installation kits that are required when you install turbine precleaners in certain applications. The kits allow the installation of turbine precleaners on products that are equipped with dust ejector systems. This Special Instruction includes the following topics:
a general procedure for removing the existing parts
instructions for assembling the installation kit and precleaner
a checklist for testing the restriction after installing the precleanerDo not perform any of the procedures until you thoroughly read the information in this Special Instruction.Refer to the appropriate module of the Service Manual for complete disassembly and assembly information.Refer to PELE0844, "TURBINE PRE-CLEANER ADAPTER KITS AVAILABLE FOR MACHINES WITH DUST EJECTORS" for the diameter of the air inlet pipe and the diameter of the air cleaner inlet.Removal of Existing Parts
Remove the dust ejector hose from the dust ejector system. Remove the dust ejector hose from the muffler.Note: If the dust ejector hose connects to the exhaust extension, proceed with Step 2. If the dust ejector hose connects to the muffler, proceed with Step 4.
Remove the exhaust extension which has the port for the dust ejector hose. Replace the exhaust extension with a length of straight tubing. The installation kit does not include the straight tubing.
Remove the rain cap from the original exhaust extension. Install the rain cap on the new exhaust extension.
Illustration 1 g00791596
(1) Bolt
(2) Washer
(3) Cap
(4) Gasket
(5) Flange
Close the port in the muffler. The port will be either a flange with a hole, or the port will be a round hole. If the port has a flange, cap the port with the bolts (1), washers (2), cap (3), and gasket (4). The installation kit includes the parts. Refer to Illustration 1. If the port is a round hole, use an appropriate plug to close the hole.
Loosen the clamp that secures the dust ejector to the air filter housing. Remove the dust ejector from the machine.Installation Instructions for 206-7515 Installation Kits and 206-7517 Installation Kits
Illustration 2 g00791588
(1) Rubber Insert
(2) Clamp
(3) Air Inlet Pipe
(4) Dust Boot
(5) Rubber Insert
(6) Clamp
(7) Turbine Precleaner
Compare the diameter of the new air inlet pipe (3) to the diameter of the air cleaner inlet. If necessary, install the rubber insert (1) on the air cleaner inlet.
Install the new air inlet pipe (3) on the air cleaner inlet or on the rubber insert (1). Tighten the clamp (2) to secure the air inlet pipe.
Install the dust boot (4) on the air inlet pipe (3). Allow the dust boot to rest on the hood.Note: If you are installing a 206-7515