AVSPARE.COM
parts catalog

GUARD AS 3236597 - Caterpillar



3236597 GUARD AS Caterpillar parts GUARD
Rating:
41
Alternative (cross code) number:
CA3236597
323-6597
3236597
Caterpillar 3236597 GUARD AS

Buy GUARD AS 3236597 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00104545Procedure To Bleed the Conveyor Charge Pump
Illustration 2 g06185015
View showing location of hose connection to disconnect
Disconnect the vibratory supply hose at the screed connection. The dash 12 vibratory supply connection has a test port at the tee. Disconnect the hose directly before this tee fitting as indicated in Illustration 2.
Illustration 3 g06184982
View showing the vibratory supply fitting on the paver
Note: Some models do not have a test port as described. Locate the vibratory supply fitting on the paver, as shown in illustration 3. Follow that hose to screed, and disconnect there.
Place the disconnected hose in a suitable container (such as a large bucket).
Illustration 4 g06086358
View showing "Pave" mode
Start the engine. Place machine in the "Pave" mode.
Illustration 5 g06086374
View showing "Parking Brake"
Engage "Parking Brake".
Illustration 6 g06086378
View showing propel lever and propel lever trigger
Squeeze propel lever trigger and place propel lever "Forward".
Illustration 7 g06086384
View showing "Compaction" button
Press "Screed Display" button on the left side of the display to enter "Compaction" screen.
Illustration 8 g06086396
View showing "Screed Vibe" icon on compaction screen
Touch "Screed Vibe" icon on the compaction screen. "Screed Vibe" icon will turn green.
Illustration 9 g06086413
View showing "Manual" buttons
Observe disconnected hose for oil flow.If steady oil flow is present:
turn off "Vibratory" function
shutdown machine
reconnect hose on screed
restart engine and check the conveyor/auger function by holding "Manual" buttonsAugers and conveyors should rotate.After 20 seconds, if steady oil flow is not present:
perform Step 9
Illustration 10 g06086428
View showing throttle switch
Hold throttle switch to slowly increase engine idle, while observing disconnected hose for steady oil flow. When steady oil flow is observed, place engine in low idle and shutdown machine. Reconnect hose on screed. Restart machine and check augers/conveyors for operation.


Parts guard Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.