AVSPARE.COM
parts catalog

GUARD GP 3237108 - Caterpillar



3237108 GUARD GP Caterpillar parts C2.2 GUARD
Rating:
71
Alternative (cross code) number:
CA3237108
323-7108
3237108
Caterpillar 3237108 GUARD GP

Buy GUARD GP 3237108 Caterpillar genuine, new aftermarket tractor parts with delivery
GENERATOR SET,

Compatible equipment models: 3237108:

GENERATOR SET  C2.2   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g01984955
Schematic of the Solenoid Valve (Pump Control)This diagnostic code is associated with the Solenoid Valve (Pump Control). The FMI 03 diagnostic code means that the Implement ECM has determined that the voltage of the solenoid circuit is above normal. The possible causes of the diagnostic code are listed below:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This failure is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0499 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:The Implement pump will produce maximum flow. The implements may be jerky. Fuel economy will be reduced. Oil temperatures may be higher.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J1-65 (wire H707-YL) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-65 (H707-YL) and the circuit that has a low resistance measurement. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 0499 FMI 03 diagnostic code is active.Expected Result:The CID 0499 FMI 03 diagnostic code is active.Results:
YES - The CID 0499 FMI 03 diagnostic code is active. The problem has not been corrected. The ECM may have failed.Repair: Failure of the ECM is unlikely. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the Implement ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NO - The CID 0499 FMI 03 diagnostic code is not active. The problem does not exist at this time.Repair: The initial diagnostic code was likely caused by a poor electrical connection or a short at one of the harness connectors that was disconnected. Resume normal machine operation.STOP

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts guard Caterpillar catalog:

2921988 GUARD
3011C, 3013C, 3024C, C1.1, C1.5, C2.2
3039145 GUARD GP-TRACK GUIDE
320D, 320D FM, 320D FM RR
3783791 GUARD GP-TRACK ROLLER
D6T LGP, D6T LGPPAT, D6T XL
1165516 GUARD GP-BELT
3406B, 3406C, G3406
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.