AVSPARE.COM
parts catalog

GUARD AS 3237115 - Caterpillar



3237115 GUARD AS Caterpillar parts C2.2 GUARD
Rating:
24
Alternative (cross code) number:
CA3237115
323-7115
3237115
Caterpillar 3237115 GUARD AS
Weight: 4 pounds 1 kg.

Buy GUARD AS 3237115 Caterpillar genuine, new aftermarket tractor parts with delivery
GENERATOR SET,

Compatible equipment models: 3237115:

GENERATOR SET  C2.2   Caterpillar
Number on catalog scheme: 2
 
  For full view, you need register

Information:


Personal injury or death can result from sudden machine movement.Sudden movement of the machine or the release of oil under pressure can cause injury to persons on or near the machine. To prevent possible injury before testing and adjusting the hydraulic system, perform the procedure in the Testing and Adjusting, "General Information" section.
Start the engine. Operate the engine at high idle.
Move the hoist control to the RAISE position. Hold the hoist control in the RAISE position for five seconds after the dump body is fully raised. Then, lower the dump body all the way to the truck frame.
Repeat Step 2 until the temperature of the hydraulic oil is 38 °C (100 °F). Cycle Times for Hoist Cylinders
Lower the dump body to the truck frame.
Operate the engine at high idle.
Raise the dump body to the fully raised position. Use a stopwatch to measure the required time. The required time for full extension of the hoist cylinders is 11 seconds.Cylinder Drift
Note: Perform this test with an empty dump body and hydraulic oil above 38°C (100°F).
Move the hoist control to the RAISE position.
When the first stage of the hoist cylinders is extended by 305 mm (12 inch), move the hoist control to the HOLD position.
The dump body will push the cylinder head of the first stage by 6.35 mm (0.250 inch) onto the second stage of the hoist cylinders. Use a stopwatch and record the required time. The acceptable time for cylinder drift is relative to the temperature of the hydraulic oil in the hoist cylinders. See Table 1 for the acceptable time.
Table 1
Acceptable Cylinder Drift
Minutes Oil Temperature Cylinder Drift
7.0 38° to 48°C (100° to 119°F) 6.35 mm (0.250 inch)
4.1 49° to 64°C (120° to 149°F) 6.35 mm (0.250 inch)
3.0 65 °C (150 °F) 6.35 mm (0.250 inch) Excessive cylinder drift can be caused by the following conditions:
Leaks in the lines between the hydraulic oil tank and the hoist cylinders
Worn control valve spool
Worn seals in the hoist cylinders

Caterpillar parts catalog:

Caterpillar parts catalog
C2.2 Generator Set GBE00001-UP


Parts guard Caterpillar catalog:

2921988 GUARD
3011C, 3013C, 3024C, C1.1, C1.5, C2.2
2667268 GUARD-SWITCH
785C, 785D, 789C, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, C32
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.