7G8389 GUARD Caterpillar parts
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
Rating:
Alternative (cross code) number:
CA7G8389
7G-8389
7G8389
CA7G8389
7G-8389
7G8389
Weight: 6 pounds 2 kg.
TRACK-TYPE TRACTOR,
Related part:
7G8389
GUARD-YM
5404302
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 7G8389 Guard for Model D6D/D6E/D6E SR/D6G/D6G SR/D6G2 XL
CTP For Model D6D/D6E/D6E SR/D6G/D6G SR/D6G2 XL || Sold in each || Easy in-and-out fit
CTP For Model D6D/D6E/D6E SR/D6G/D6G SR/D6G2 XL || Sold in each || Easy in-and-out fit
CTP 7G8389 Guard for Model D6D/D6E/D6E SR/D6G/D6G SR/D6G2 XL
CTP For Model D6D/D6E/D6E SR/D6G/D6G SR/D6G2 XL || Sold in each || Easy in-and-out fit
CTP For Model D6D/D6E/D6E SR/D6G/D6G SR/D6G2 XL || Sold in each || Easy in-and-out fit
Compatible equipment models: 7G8389:
Information:
Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
B     5P-1733     Seal Locator     1    
C     5P-1737     Bolt     3    
D     9S-8858     Nut (Seal Installer)     1    
E     6V-6143     Seal Installer     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft rear seal and the wear sleeve must be replaced at the same time. Once the crankshaft rear seal and the wear sleeve are separated, these components cannot be used again.
Illustration 1 g01007913
Note: Do not use any type of lubricant during the installation of the crankshaft seal and wear sleeve.
Before installation of the crankshaft seal and the wear sleeve, inspect the crankshaft for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to an out of round condition. Use a polishing cloth in order to remove any imperfections on the crankshaft.
Clean the outside diameter of the crankshaft and the inside diameter of the wear sleeve.
Fasten Tooling (B) to the crankshaft with Tooling (C) .Note: Install the crankshaft rear seal with the arrow that shows the direction of crankshaft rotation toward the rear of the engine.
Position wear sleeve (2) and crankshaft rear seal (1) on Tooling (B). Install Tooling (E) on Tooling (B). Lubricate the face of the washer on Tooling (D). Install Tooling (D) on Tooling (B) .
Tighten Tooling (D) until Tooling (E) contacts Tooling (B) .
Remove Tooling (D) and Tooling (E) from Tooling (B) .
Remove Tooling (C) and Tooling (B) from the crankshaft.
Check the crankshaft rear seal and the wear sleeve for the correct installation.End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
B     5P-1733     Seal Locator     1    
C     5P-1737     Bolt     3    
D     9S-8858     Nut (Seal Installer)     1    
E     6V-6143     Seal Installer     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft rear seal and the wear sleeve must be replaced at the same time. Once the crankshaft rear seal and the wear sleeve are separated, these components cannot be used again.
Illustration 1 g01007913
Note: Do not use any type of lubricant during the installation of the crankshaft seal and wear sleeve.
Before installation of the crankshaft seal and the wear sleeve, inspect the crankshaft for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to an out of round condition. Use a polishing cloth in order to remove any imperfections on the crankshaft.
Clean the outside diameter of the crankshaft and the inside diameter of the wear sleeve.
Fasten Tooling (B) to the crankshaft with Tooling (C) .Note: Install the crankshaft rear seal with the arrow that shows the direction of crankshaft rotation toward the rear of the engine.
Position wear sleeve (2) and crankshaft rear seal (1) on Tooling (B). Install Tooling (E) on Tooling (B). Lubricate the face of the washer on Tooling (D). Install Tooling (D) on Tooling (B) .
Tighten Tooling (D) until Tooling (E) contacts Tooling (B) .
Remove Tooling (D) and Tooling (E) from Tooling (B) .
Remove Tooling (C) and Tooling (B) from the crankshaft.
Check the crankshaft rear seal and the wear sleeve for the correct installation.End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar parts catalog:
Parts guard Caterpillar catalog:
9W1669
GUARD
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
8M7207
GUARD AS-FRAME-RH
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
8M7208
GUARD AS-FRAME
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
4S5049
GUARD AS
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
4S5050
GUARD AS
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
8M6217
GUARD-IDLER
955K, 955L, D6C, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
955K, 955L, D6C, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
8M6218
GUARD-IDLER
955K, 955L, D6C, D6D, D6E, D6E SR, D6G SR, D6G2 LGP, D6G2 XL
955K, 955L, D6C, D6D, D6E, D6E SR, D6G SR, D6G2 LGP, D6G2 XL
9W1668
GUARD
D6D, D6E
D6D, D6E
7M2523
GUARD
D6C, D6D
D6C, D6D
9S8258
GUARD ASSEM.
D5, D5B, D6C, D6D
D5, D5B, D6C, D6D
7M0457
GUARD
D6C, D6D, D6F SR
D6C, D6D, D6F SR
2S6263
GUARD GROUP
D6C, D6D, D6F SR
D6C, D6D, D6F SR
5Y2027
GUARD AS-RADIATOR
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
9M5045
GUARD AS-WEAR
D6C, D6D, D6E SR, D6G2 LGP, D6G2 XL
D6C, D6D, D6E SR, D6G2 LGP, D6G2 XL
9M3435
GUARD AS
D6C, D6D, D6E SR, D6G SR
D6C, D6D, D6E SR, D6G SR
5Y1970
GUARD AS-CRANKCASE
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
5Y2065
GUARD AS-CRANKCASE
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
5Y2568
GUARD AS-RADIATOR
D6E, D6E SR, D6G SR
D6E, D6E SR, D6G SR
8M7208
GUARD AS-FRAME
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
8M7207
GUARD AS-FRAME-RH
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
9W1669
GUARD
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
7G8400
GUARD AS-TRACK ROLLER
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP
7G8513
GUARD AS
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP
7G8517
GUARD AS
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP
D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP