3443444 HANDRAIL AS Caterpillar parts
10-20B, AP-1055D, BG-2455D, BG-260D
Rating:
Alternative (cross code) number:
CA3443444
344-3444
3443444
CA3443444
344-3444
3443444
ASPHALT PAVER, ASPHALT SCREED,
Compatible equipment models: 3443444:
Number on catalog scheme:
1
For full view, you need register
Caterpillar parts catalog:
Information:
Specification
Table 1
"Travel on Level Ground - Test (Optional Test)"
Time for Three Revolutions (time in seconds)
Undercarriage Travel Speed New Service Limit Actual
Right Left
Long HIGH Forward 18.4 1.0 23.9 or less
Reverse
LOW Forward 30.5 1.5 39.7 or less
Reverse Introduction
When the procedure for the Travel on Level Ground cannot be performed, this test may be used as a substitute.Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".Required Tools
Table 2
Required Tools
Description Qty
Stopwatch 1 Test Procedure
Start the engine.
Position the machine on level ground.
Place the hydraulic activation control lever in the UNLOCKED position.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Illustration 1 g00297292
Raise a track off the ground. Refer to Illustration 1.
Put a mark on a shoe of the raised track.
Place the machine controls at the following settings: Engine speed dial "10" and AEC switch OFF.
Place the travel speed control switch in HIGH position.
Move the travel lever of the raised track to full travel position.
Measure the time that is required for the raised track to make three complete revolutions. Measure the time that is required in each direction.Note: The difference in times between forward and reverse should not exceed 0.5 seconds for HIGH travel speed and 1.0 seconds for LOW travel speed.
Place the travel speed control switch in the LOW position and repeat Steps 9 through 10.
Table 1
"Travel on Level Ground - Test (Optional Test)"
Time for Three Revolutions (time in seconds)
Undercarriage Travel Speed New Service Limit Actual
Right Left
Long HIGH Forward 18.4 1.0 23.9 or less
Reverse
LOW Forward 30.5 1.5 39.7 or less
Reverse Introduction
When the procedure for the Travel on Level Ground cannot be performed, this test may be used as a substitute.Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".Required Tools
Table 2
Required Tools
Description Qty
Stopwatch 1 Test Procedure
Start the engine.
Position the machine on level ground.
Place the hydraulic activation control lever in the UNLOCKED position.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Illustration 1 g00297292
Raise a track off the ground. Refer to Illustration 1.
Put a mark on a shoe of the raised track.
Place the machine controls at the following settings: Engine speed dial "10" and AEC switch OFF.
Place the travel speed control switch in HIGH position.
Move the travel lever of the raised track to full travel position.
Measure the time that is required for the raised track to make three complete revolutions. Measure the time that is required in each direction.Note: The difference in times between forward and reverse should not exceed 0.5 seconds for HIGH travel speed and 1.0 seconds for LOW travel speed.
Place the travel speed control switch in the LOW position and repeat Steps 9 through 10.
Parts handrail Caterpillar catalog:
2511577
HANDRAIL AS
10-20B, AP-1055D, BG-2455D, BG-260D
10-20B, AP-1055D, BG-2455D, BG-260D
2511576
HANDRAIL AS
10-20B, AP-1055D, BG-2455D, BG-260D
10-20B, AP-1055D, BG-2455D, BG-260D
1084620
HANDRAIL AS
SM-350
SM-350
2324641
HANDRAIL AS
8-16B, AP-800C, AP-800D, AS2251, BG-225B
8-16B, AP-800C, AP-800D, AS2251, BG-225B
2316635
HANDRAIL AS
8-16B, AP-800C, AP-800D, AS2251, BG-225B
8-16B, AP-800C, AP-800D, AS2251, BG-225B
8I0981
HANDRAIL AS
10 FT, 10-20B, AP-1055D, BG-2455D, BG-260D
10 FT, 10-20B, AP-1055D, BG-2455D, BG-260D
1196193
HANDRAIL AS
CB-434B
CB-434B
1168544
HANDRAIL AS
CB-434B, CB-434C
CB-434B, CB-434C
1261864
HANDRAIL AS
PF-300C, PS-300B
PF-300C, PS-300B
1362997
HANDRAIL AS
CB-434B, CB-434C, CB-534B, CB-534C, CB-535B
CB-434B, CB-434C, CB-534B, CB-534C, CB-535B
1266039
HANDRAIL AS
CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, PF-300C, PS-300B
CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, PF-300C, PS-300B
1198826
HANDRAIL AS
CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545
CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545