1570946 HARNESS AS-LIGHTING Caterpillar parts
325B L, 325C, 345B II, 345B L, 365B, 365C L MH
Rating:
Alternative (cross code) number:
CA1570946
157-0946
1570946
CA1570946
157-0946
1570946
Weight: 1 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 1570946:
Number on catalog scheme:
12
For full view, you need register
Information:
start by:a) remove fuel injection pump housing and governor.1. Loosen alternator mounting bolt and adjustment bolt for belt tension. Push alternator toward engine to loosen belts. 2. Remove accessory drive gear cover, then remove nut (2) and washer (1) from gear. 3. Install tooling (B) on drive gear and loosen it from accessory drive shaft. 4. Remove all lines and hoses (4) from accessory drive housing (3). 5. Turn the engine until the four holes in the drive gear are in alignment with the four bolt heads that hold the accessory drive housing to the engine. Remove these four bolts and the accessory drive housing and shaft. 6. Remove fuel transfer pump (5). Remove sleeve (6). Remove shaft and bearing assembly (7). 7. Remove bearing (8) from shaft with tool (A).Install Accessory Driving Housing And Shaft
1. Install bearing on shaft with a press. Install bearing and shaft assembly (1) into accessory drive housing. 2. Put a new gasket on the fuel transfer pump (2) and in the pump in the housing. Install sleeve (3) on housing. 3. Install a new gasket where the accessory drive housing fastens to the timing gear plate. Put accessory drive housing and shaft in position on the engine. Install the four bolts through the holes in the drive gear. Connect all lines and hoses to accessory drive housing.4. Put No. 1 piston at top center (TC) compression position. For correct method see INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR AS A UNIT.5. Turn accessory drive shaft until tool (A) can be installed. Install washer on drive shaft so outside diameter makes contact with the gear first. Install nut and tighten it to a torque of 100 10 lb.ft. (135 14 N m). Remove tool (A). Install drive gear cover.6. Install belts on pulley. Make an adjustment to the belts so 25 lb. (110 N) force made on the belts half way between the pulleys will cause a restriction of movement between 1/2 to 3/4 in. (12.7 to 19.1 mm) on used belts.end by:a) install fuel injection pump housing and governor as a unit
1. Install bearing on shaft with a press. Install bearing and shaft assembly (1) into accessory drive housing. 2. Put a new gasket on the fuel transfer pump (2) and in the pump in the housing. Install sleeve (3) on housing. 3. Install a new gasket where the accessory drive housing fastens to the timing gear plate. Put accessory drive housing and shaft in position on the engine. Install the four bolts through the holes in the drive gear. Connect all lines and hoses to accessory drive housing.4. Put No. 1 piston at top center (TC) compression position. For correct method see INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR AS A UNIT.5. Turn accessory drive shaft until tool (A) can be installed. Install washer on drive shaft so outside diameter makes contact with the gear first. Install nut and tighten it to a torque of 100 10 lb.ft. (135 14 N m). Remove tool (A). Install drive gear cover.6. Install belts on pulley. Make an adjustment to the belts so 25 lb. (110 N) force made on the belts half way between the pulleys will cause a restriction of movement between 1/2 to 3/4 in. (12.7 to 19.1 mm) on used belts.end by:a) install fuel injection pump housing and governor as a unit
Caterpillar parts catalog:
Parts harness Caterpillar catalog:
120H, 135H, 3126B, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
1160098
HARNESS AS-WIRING
307B, 312B L, 312C, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320C, 322B LN, 322C, 325B L, 325C, 330B L, 330C, 330C L, 345B II, 345B L, 365B, 365B II, 385B, 5090B
307B, 312B L, 312C, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320C, 322B LN, 322C, 325B L, 325C, 330B L, 330C, 330C L, 345B II, 345B L, 365B, 365B II, 385B, 5090B
1986223
HARNESS AS-LIGHTING
312C, 312D, 315C, 315D L, 318C, 319C, 319D, 320C, 322C, 323D L, 323D LN, 324D, 324D LN, 325C, 325D, 325D L, 329D L, 330C, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D L, 336D LN, 345C, 345C L, 345D, 3...
312C, 312D, 315C, 315D L, 318C, 319C, 319D, 320C, 322C, 323D L, 323D LN, 324D, 324D LN, 325C, 325D, 325D L, 329D L, 330C, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D L, 336D LN, 345C, 345C L, 345D, 3...
320B, 322B LN, 325B L
1544847
HARNESS AS
320B, 325B L, 330B L
320B, 325B L, 330B L
1557665
HARNESS AS
320B, 325B L, 330B L
320B, 325B L, 330B L
320D L, 323D L, 324D, 324D L, 324D LN, 325D, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 345C, 345...
1419134
HARNESS AS-LIGHTING
325B L, 330B L, M325C MH, M325D L MH, M325D MH, M330D
325B L, 330B L, M325C MH, M325D L MH, M325D MH, M330D
1617266
HARNESS AS
325B L, 330B L
325B L, 330B L
1419134
HARNESS AS-LIGHTING
325B L, 330B L, M325C MH, M325D L MH, M325D MH, M330D
325B L, 330B L, M325C MH, M325D L MH, M325D MH, M330D
1526974
HARNESS AS-LIGHTING
325B L, 330B L, M325C MH, M325D L MH, M325D MH
325B L, 330B L, M325C MH, M325D L MH, M325D MH
1419132
HARNESS AS
325B L, 330B L
325B L, 330B L
1537412
HARNESS AS
325B L
325B L
1994167
HARNESS AS
325B L, 330B L, 345B II, 345B L
325B L, 330B L, 345B II, 345B L
1419131
HARNESS AS
325B L, 330B L
325B L, 330B L
1994798
HARNESS AS
325B L, 330B L, 345B II, 345B L
325B L, 330B L, 345B II, 345B L
1994797
HARNESS AS
325B L, 330B L, 345B II, 345B L
325B L, 330B L, 345B II, 345B L
1422674
HARNESS AS
325B L, 330B L, 345B L
325B L, 330B L, 345B L
1422673
HARNESS AS
325B L, 330B L, 345B L
325B L, 330B L, 345B L
2049044
HARNESS AS-LIGHTING
325B L, 365B
325B L, 365B
2030020
HARNESS AS
325B L, 365B
325B L, 365B