1703519 HARNESS AS-WIRING Caterpillar parts
3126B
Rating:
Alternative (cross code) number:
CA1703519
170-3519
1703519
CA1703519
170-3519
1703519
Weight: 0.05 pounds 0 kg.
TRUCK ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
This part in 2 request:
Show.
This information for suppliers only!
2021-04-03
2019-04-01
Compatible equipment models: 1703519:
Information:
Marine Engines:
3508B (S/N: 2BM; 3DM; 7SM; 1TW; 3DW)
3508 (S/N: 3PS; 3TS)
3512B (S/N: 7HM; 8EM; 4TN; 1PW; 2GW)
3512 (S/N: 3RS; 3WS)
3516B (S/N: 8CN; 8KN; 9AN; 2FW; 3CW)
3516 (S/N: 3SS; 3XS)
Generator Set Engines:
3508B (S/N: 4GM; 6PN; 2HW)
3508 (S/N: 1ZF; 5XM; 3LS)
3512B (S/N: 8RM; 6WN; 4AW)
3512 (S/N: 6PM; 3MS)
3516B (S/N: 6HN; 7RN)
3616 (S/N: 7KM; 3NS)
Gas Engines:
G3508 (S/N: 4WD; 2JF; 9TG; 9AW)
G3512 (S/N: 4KC; 5JD; 7NJ; 6JW)
G3516 (S/N: 3RC; 8LD; 4EK; 5PN; 8PW)
Engine News SEBD9268, July 1998, "114-2410 Digital Pyrometer Battery Shelf Life Extender". Disregard this article. The article has been replaced by the following article:A modification to the 114-2410 Pyrometer has increased the shelf life of the digital pyrometer battery from 1.5 years to 5 years. The battery shelf life will decrease with an increase in ambient temperatures. This modification is effective with 114-2410 Pyrometer serial numbers 4018 and Up.A Field Modification Procedure has been developed in order to provide increased shelf life to earlier pyrometers. This field modification is adaptable to 114-2410 Pyrometer serial numbers 3001 through 4017. This field modification can be performed when the pyrometer batteries are changed.Field Modification Procedure
Loosen the four screws that go through the front keypad so that the device comes apart.
Remove the three batteries.
Remove the three small screws that fasten the circuit board to the front keypad plate. Do NOT LOSE these screws.
Find the location of the resistor "R11B" on the display side of the circuit board. "R11B" is on the lower left corner of the circuit board. Use small wire cutters to carefully cut the leads at each end of the resistor "R11B". Use care not to damage the resistor "R11C". Resistor "R11C" is located immediately above resistor "R11B".
Use the three small screws that were retained in Step 3 to install the circuit board on the keypad plate.
Install three new batteries. The following batteries are recommended: Duracell PX28L, Sanyo 2CR-1/3N and Altronic 601258. Take note of the battery polarity during installation.
Reassemble the pyrometer and install the four screws that were removed in Step 2.
3508B (S/N: 2BM; 3DM; 7SM; 1TW; 3DW)
3508 (S/N: 3PS; 3TS)
3512B (S/N: 7HM; 8EM; 4TN; 1PW; 2GW)
3512 (S/N: 3RS; 3WS)
3516B (S/N: 8CN; 8KN; 9AN; 2FW; 3CW)
3516 (S/N: 3SS; 3XS)
Generator Set Engines:
3508B (S/N: 4GM; 6PN; 2HW)
3508 (S/N: 1ZF; 5XM; 3LS)
3512B (S/N: 8RM; 6WN; 4AW)
3512 (S/N: 6PM; 3MS)
3516B (S/N: 6HN; 7RN)
3616 (S/N: 7KM; 3NS)
Gas Engines:
G3508 (S/N: 4WD; 2JF; 9TG; 9AW)
G3512 (S/N: 4KC; 5JD; 7NJ; 6JW)
G3516 (S/N: 3RC; 8LD; 4EK; 5PN; 8PW)
Engine News SEBD9268, July 1998, "114-2410 Digital Pyrometer Battery Shelf Life Extender". Disregard this article. The article has been replaced by the following article:A modification to the 114-2410 Pyrometer has increased the shelf life of the digital pyrometer battery from 1.5 years to 5 years. The battery shelf life will decrease with an increase in ambient temperatures. This modification is effective with 114-2410 Pyrometer serial numbers 4018 and Up.A Field Modification Procedure has been developed in order to provide increased shelf life to earlier pyrometers. This field modification is adaptable to 114-2410 Pyrometer serial numbers 3001 through 4017. This field modification can be performed when the pyrometer batteries are changed.Field Modification Procedure
Loosen the four screws that go through the front keypad so that the device comes apart.
Remove the three batteries.
Remove the three small screws that fasten the circuit board to the front keypad plate. Do NOT LOSE these screws.
Find the location of the resistor "R11B" on the display side of the circuit board. "R11B" is on the lower left corner of the circuit board. Use small wire cutters to carefully cut the leads at each end of the resistor "R11B". Use care not to damage the resistor "R11C". Resistor "R11C" is located immediately above resistor "R11B".
Use the three small screws that were retained in Step 3 to install the circuit board on the keypad plate.
Install three new batteries. The following batteries are recommended: Duracell PX28L, Sanyo 2CR-1/3N and Altronic 601258. Take note of the battery polarity during installation.
Reassemble the pyrometer and install the four screws that were removed in Step 2.
Caterpillar SIS machinery equipment:
Parts harness Caterpillar catalog:
1617153
HARNESS AS
3126B
3126B
1593487
HARNESS AS-SENSOR
3126B, 3126E
3126B, 3126E
1605482
HARNESS AS-SENSOR
3126B, 3126E
3126B, 3126E
2780086
HARNESS AS-MONITOR
3024, 3116, 3126, 3126B, 3126E, 3176B, 3406E, C-10, C-12, C-15, C-16, C-9, C11, C13, C15, C7, C9, DEUCE
3024, 3116, 3126, 3126B, 3126E, 3176B, 3406E, C-10, C-12, C-15, C-16, C-9, C11, C13, C15, C7, C9, DEUCE
1436565
HARNESS-POWER
3116, 3126, 3126B, 3176, 3306, 3406B, 3406C, D350E, D400E
3116, 3126, 3126B, 3176, 3306, 3406B, 3406C, D350E, D400E
1487409
HARNESS-RELAY
3116, 3126, 3126B
3116, 3126, 3126B
2051251
HARNESS AS
3126B, 3126E
3126B, 3126E
2051252
HARNESS AS
3126, 3126B, 3126E
3126, 3126B, 3126E
2051253
HARNESS AS
3126, 3126B, 3126E
3126, 3126B, 3126E
1593488
HARNESS AS-WIRING
3126B, 3126E
3126B, 3126E
1605482
HARNESS AS-SENSOR
3126B, 3126E
3126B, 3126E
1593487
HARNESS AS-SENSOR
3126B, 3126E
3126B, 3126E
1617153
HARNESS AS
3126B
3126B
4370266
HARNESS AS-PANEL
3406B
3406B
2466531
HARNESS AS-SENSOR
3512, 3512B
3512, 3512B
3478326
HARNESS AS-CONTROL
3512, 3512B, 3516, 3516B
3512, 3512B, 3516, 3516B
2342201
HARNESS AS-CONTROL
3512B, 3516B
3512B, 3516B
1488021
HARNESS GP-WIRING
3508, 3508B, PM3508
3508, 3508B, PM3508
2466530
HARNESS AS-WIRING
3508, 3508B
3508, 3508B