1974411 HARNESS AS-CHASSIS Caterpillar parts
330C, 330C FM, 330C L, 330C MH
Rating:
Alternative (cross code) number:
CA1974411
197-4411
1974411
CA1974411
197-4411
1974411
Weight: 2 pounds 1 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
You can buy:
US$284.00
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Artemisia 197-4411 Hydraulic Pump Wiring Harness 1974411 for E330C Excavator Wire
Artemisia 197-4411 Hydraulic Pump Wiring Harness 1974411 For E330C Excavator Wire Harness
Artemisia 197-4411 Hydraulic Pump Wiring Harness 1974411 For E330C Excavator Wire Harness
1974411 197-4411 C13/C9/C7 Engine E345B 330D 336D 325D 324D Hydraulic Pump Wire Harness Excavator Parts
NDVQMULGW High temperature resistance, high precision, low resistance, better conductivity, and strong adaptability. || Strong antioxidant capacity, stable voltage without overheating, stable conductivity, energy-saving and power-saving. || Stable output current, less prone to short circuits, flame retardant, uniform thickness of insulation layer outer skin, ensuring safety. || The original car data is integrated and sturdy, with simple and convenient replacement of original components and precise positioning. || Good quality, strong tensile, wear-resistant, waterproof, and sun protection toughness, not easily damaged, strong abrasion resistance, good effect, and long service life.
NDVQMULGW High temperature resistance, high precision, low resistance, better conductivity, and strong adaptability. || Strong antioxidant capacity, stable voltage without overheating, stable conductivity, energy-saving and power-saving. || Stable output current, less prone to short circuits, flame retardant, uniform thickness of insulation layer outer skin, ensuring safety. || The original car data is integrated and sturdy, with simple and convenient replacement of original components and precise positioning. || Good quality, strong tensile, wear-resistant, waterproof, and sun protection toughness, not easily damaged, strong abrasion resistance, good effect, and long service life.
1974411 197-4411 C13 C9 C7 Engine E345B 330D 336D 325D 324D Hydraulic Pump Wire Harness Excavator Parts
QZXUIGIZ Integrated design of wiring harness, simple installation and convenient use. || Solve the problems of aging, peeling and short circuit of the wiring harness inside the vehicle. || Wiring harness ensures the stable operation of the vehicle electrical system and reduces vehicle failures. || Wiring harness has strong durability and can work stably in various environments such as high temperature and vibration. || 1974411 197-4411 C13 C9 C7 Engine E345B 330D 336D 325D 324D Hydraulic Pump Wire Harness Excavator Parts
QZXUIGIZ Integrated design of wiring harness, simple installation and convenient use. || Solve the problems of aging, peeling and short circuit of the wiring harness inside the vehicle. || Wiring harness ensures the stable operation of the vehicle electrical system and reduces vehicle failures. || Wiring harness has strong durability and can work stably in various environments such as high temperature and vibration. || 1974411 197-4411 C13 C9 C7 Engine E345B 330D 336D 325D 324D Hydraulic Pump Wire Harness Excavator Parts
Number on catalog scheme:
17
For full view, you need register
Compatible equipment models: 1974411:
Information:
Introduction
The following information describes the procedure for Removing and Replacing the Position Sensor (Tilt Linkage).Test Preparation
Reference: For additional information about preparing the machine for troubleshooting the machine, refer to the Service Manual module Troubleshooting, "Machine Preparation for Troubleshooting" for the machine that is being serviced.Test Procedure
Tilt the bucket to a position level with the ground. Lower the bucket to the ground.
Connect the steering frame lock link.
Engage the parking brake.
Stop the engine and leave the key start switch in the OFF position.
Illustration 1 g03671990
Right side of lift arm crossmember
(52) Tilt linkage position sensor
Disconnect the harness connector from the sensor connector.
Remove the fork from the Tilt Linkage Position Sensor.
Remove the guard from the tilt lever.
Remove the bracket from the lift arm crossmember.
Remove the Tilt Linkage Position Sensor from the bracket
Install the new Tilt Linkage Position Sensor on the bracket.
Install the bracket on the lift arm crossmember.
Install the guard on the tilt lever casting.
Install the fork on the new Tilt Linkage Position Sensor
Connect the harness connector to the sensor connector.
The Tilt Linkage Position Sensor must be calibrated before the machine is returned to use. Adjustment Procedure
Reference: For the correct procedure in order to calibrate the Tilt Linkage Position Sensor, refer to Testing and Adjusting, UENR3849 , "Calibrations (Cat ET)" for the correct calibration procedure.
The following information describes the procedure for Removing and Replacing the Position Sensor (Tilt Linkage).Test Preparation
Reference: For additional information about preparing the machine for troubleshooting the machine, refer to the Service Manual module Troubleshooting, "Machine Preparation for Troubleshooting" for the machine that is being serviced.Test Procedure
Tilt the bucket to a position level with the ground. Lower the bucket to the ground.
Connect the steering frame lock link.
Engage the parking brake.
Stop the engine and leave the key start switch in the OFF position.
Illustration 1 g03671990
Right side of lift arm crossmember
(52) Tilt linkage position sensor
Disconnect the harness connector from the sensor connector.
Remove the fork from the Tilt Linkage Position Sensor.
Remove the guard from the tilt lever.
Remove the bracket from the lift arm crossmember.
Remove the Tilt Linkage Position Sensor from the bracket
Install the new Tilt Linkage Position Sensor on the bracket.
Install the bracket on the lift arm crossmember.
Install the guard on the tilt lever casting.
Install the fork on the new Tilt Linkage Position Sensor
Connect the harness connector to the sensor connector.
The Tilt Linkage Position Sensor must be calibrated before the machine is returned to use. Adjustment Procedure
Reference: For the correct procedure in order to calibrate the Tilt Linkage Position Sensor, refer to Testing and Adjusting, UENR3849 , "Calibrations (Cat ET)" for the correct calibration procedure.
Cat SIS web machinery list:
Parts harness Caterpillar catalog:
140M, 140M 2, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521, 521B, 522, 5...
12H, 140M, 140M 2, 160M, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 340D L, 511, 521, 521B, 522, 522B, 532, 541, 541 ...
12H, 330C, 330C FM, 330C L, 330C MH, 627G, 637G, C-9, D6R II, MTC735, TK711, TK721, TK722, TK732
12H, 330C, 330C FM, 330C L, 330C MH, 627G, 637D, 637G, C-9, D6R II, MTC735, TK711, TK721, TK722, TK732, TK741, TK751, TK752
320C, 322C, 325C, 330C, 330C L
2335018
HARNESS AS
330C
330C
2041829
HARNESS AS
330C L
330C L
2041830
HARNESS AS
330C L
330C L
8X9386
HARNESS AS
120G, 12G, 130G, 140G, 14G, 160G, 16G
120G, 12G, 130G, 140G, 14G, 160G, 16G
8W2865
HARNESS AS
140G
140G
8W1486
HARNESS AS
120G, 12G, 130G, 140G, 14G, 16G
120G, 12G, 130G, 140G, 14G, 16G
8W1978
HARNESS AS
120G, 12G, 130G, 140G, 14G, 160G, 16G
120G, 12G, 130G, 140G, 14G, 160G, 16G
9W3160
HARNESS AS-HEATER
120G, 12G, 130G, 140G, 14G, 16G
120G, 12G, 130G, 140G, 14G, 16G
120G, 12G, 130G, 140G, 14G, 16G
8W3022
HARNESS AS
120G, 12G, 130G, 140G, 14G, 160G
120G, 12G, 130G, 140G, 14G, 160G
8W1744
HARNESS AS
120G, 12G, 140G, 14G
120G, 12G, 140G, 14G
120G, 12G, 130G, 140G
6G4417
HARNESS ASSEMBLY
120G, 12G, 130G, 140G, 14G, 16G
120G, 12G, 130G, 140G, 14G, 16G
2677588
HARNESS AS-CHASSIS
330C, 330C L
330C, 330C L
2510140
HARNESS AS-CHASSIS
330C, 330C L
330C, 330C L