2356762 HARNESS ASSEMBLY-FRONT Caterpillar parts
561N, D5N, D6N
Rating:
Alternative (cross code) number:
CA2356762
235-6762
2356762
CA2356762
235-6762
2356762
Weight: 1 pounds 0 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Information:
Illustration 7 g00696176
Disconnect the two tires from switch assembly (16). Remove the bolt that holds the wire harness in place.
Disconnect two rod ends (15) from the lever.
Illustration 8 g00696179
Install Tooling (A) on the rear of the transmission, as shown. Fasten a hoist to Tooling (A) .
Install two 5/8 inch - 11 NC forcing screws (18). Tighten the forcing screws evenly and separate the transmission and bevel gear (17) from the main frame case.
Illustration 9 g00696181
Pull the transmission and bevel gear (17) out of the main frame case until the spacers on the plates are at the end of the rail assembly.
Put a two ton floor jack (19) or wood blocks under the transmission in order to support the transmission when the hoist is removed.
Remove the hoist and Tooling (A) .
Illustration 10 g00696183
Fasten a hoist and two forged eyebolts that are 3/4 inch - 10 NC to the transmission and bevel gear (17). Remove the floor jack. Remove the transmission and bevel gear from the machine. The weight of the transmission and bevel gear is 651 kg (1435.0 lb).Removal Procedure (Power Shift)
Table 2
Tools Needed     A     B    
FT-1897 Adapter     1        
5P-9736 Link Bracket     1     2    Start By:
Remove the drive shaft (power shift). Refer to Disassembly and Assembly, "Main Drive Shaft - Remove and Install".
Remove the axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Drain the oil from the transmission and bevel gear case.
Illustration 11 g00696187
Remove the bolts and handhold (1) from the rear of the fuel tank.
Illustration 12 g00696189
Remove bolt (4). Remove the clip and hose (5) from the fuel tank.
Remove bolts (3), cover (2), and the gasket from the rear of the transmission.
Illustration 13 g00696190
Remove the bolts, cover (7) and the gasket from the rear of the transmission.
Remove bolts (6). Disconnect the control linkage from the hydraulic control valve.
Illustration 14 g00696191
Illustration 15 g00696196
Install Tooling (A) on the rear of the transmission, as shown. Fasten a hoist to Tooling (A) .
Remove the bolts that hold the transmission and bevel gear (8) to the main frame case. Pull the transmission and bevel gear out of the main frame case until rollers (9) are at the end of the rail assemblies, as shown.
Illustration 16 g00696197
Put a two ton floor jack (10) or wood blocks under the transmission in order to support the transmission when the hoist is removed.
Remove the hoist from Tooling (A). Fasten the hoist and Tooling (B) to the transmission and bevel gear, as shown. Remove the transmission and bevel gear from the machine. The weight of the transmission and bevel gear is 424 kg (935.0 lb).
Remove the O-ring seal from the transmission and bevel gear.
Remove the three O-ring seals from the rear of main frame case.
Caterpillar SIS machinery equipment:
Caterpillar SIS
D6N TRACK-TYPE TRACTOR /PS XL/ PS LGP/ CBF00001-UP (MACHINE) POWERED BY 3126B ENGINE »
235-6762
HARNESS ASSEMBLY-FRONT
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CBL00001-UP (MACHINE) POWERED BY 3126B ENGINE »
235-6762
HARNESS ASSEMBLY
D5N TRACK-TYPE TRACTOR /XL, LGP, POWER SHIFT/ CFH00001-UP (MACHINE) POWERED BY 3126B ENGINE »
235-6762
HARNESS ASSEMBLY-FRONT
Caterpillar parts catalog:
Parts harness Caterpillar catalog:
1957336
HARNESS AS-ENGINE
120H, 135H, 3126B, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
120H, 135H, 3126B, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
1212844
HARNESS ASSEMBLY-CRANK
561N, 572R II, 583T, 587T, 953C, 963C, 973C, D10R, D10T, D11N, D11R, D5N, D6K2, D6K2 LGP, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D7E, D7R II, D7R XR, D8R, D8R II, D8T, D9R, D9T, PL...
561N, 572R II, 583T, 587T, 953C, 963C, 973C, D10R, D10T, D11N, D11R, D5N, D6K2, D6K2 LGP, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D7E, D7R II, D7R XR, D8R, D8R II, D8T, D9R, D9T, PL...
2236517
HARNESS ASSEMBLY-SENSOR
561N, D5N, D6N
561N, D5N, D6N
2132980
HARNESS ASSEMBLY-PANEL
D5N, D6N
D5N, D6N
2758264
HARNESS ASSEMBLY-PANEL
561N, D5N, D6N
561N, D5N, D6N
2343321
HARNESS ASSEMBLY-LIGHTING
D5N, D6N
D5N, D6N
2197355
HARNESS ASSEMBLY-CONTROL
561N, 953C, 963C, 973C, D5N, D6N
561N, 953C, 963C, 973C, D5N, D6N
2578099
HARNESS AS-CONTROL
D5N, D6N
D5N, D6N
2374487
HARNESS AS-PLATFORM
D5N, D6N
D5N, D6N
2367474
HARNESS AS-PLATFORM
561N, D5N, D6N
561N, D5N, D6N
2782118
HARNESS AS-CAB
561N, D5N, D6N
561N, D5N, D6N
1609147
HARNESS AS-CAB
D5N, D6N
D5N, D6N
2132985
HARNESS ASSEMBLY-PANEL
561N, D5N, D6N
561N, D5N, D6N
2191505
HARNESS AS-SWITCH
AD30, AD45B, AD55, AD55B, AD60
AD30, AD45B, AD55, AD55B, AD60
7V5214
HARNESS AS
950B, 950B/950E, 966D
950B, 950B/950E, 966D
1591178
HARNESS AS-WIRING
3508B, 3512, 3512B
3508B, 3512, 3512B
1263098
HARNESS AS-PANEL
3408, 3508B, 3512B, 3516B, G3304, G3306, G3406, G3408, G3408B, G3412, G3508, G3512, G3516
3408, 3508B, 3512B, 3516B, G3304, G3306, G3406, G3408, G3408B, G3412, G3508, G3512, G3516
1263093
HARNESS AS-PANEL
3508, 3508B, 3512, 3512B, 3516, 3516B
3508, 3508B, 3512, 3512B, 3516, 3516B
1263091
HARNESS AS-PANEL
3508, 3508B, 3512, 3512B, 3516, 3516B
3508, 3508B, 3512, 3512B, 3516, 3516B
4250512
HARNESS AS-ENGINE
834K, 836K, 988K
834K, 836K, 988K
2639234
HARNESS ASSEMBLY
D5N, D6N
D5N, D6N
1746768
HARNESS ASSEMBLY-MAIN
966G, 972G
966G, 972G