2477986 HARNESS AS-CHASSIS Caterpillar parts
M325C MH  
 
 
Rating:
 Alternative (cross code) number:
CA2477986
247-7986
2477986
 
CA2477986
247-7986
2477986
 
 
  Weight: 43 pounds 19 kg. 
  WHEELED EXCAVATOR,
Compatible equipment models: 2477986:
Information:
 Removal Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     185-3630     Strap Wrench As     1    
ZZ     6V-9509     Face Seal Plug     2    
6V-9830 Cap As     2    Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g01034596
Drain filter assembly (1) into a suitable container for storage or disposal.
Use Tooling (A) in order to remove filter assembly (1) .
Disconnect tube assemblies (2) .
Remove bolts (3) in order to remove fuel filter base assembly (4) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 2 g01034596
Install fuel filter base assembly (4) and install bolts (3) .
Connect tube assemblies (2) .
Install filter assembly (1) .
 Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     185-3630     Strap Wrench As     1    
ZZ     6V-9509     Face Seal Plug     2    
6V-9830 Cap As     2    Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g01034596
Drain filter assembly (1) into a suitable container for storage or disposal.
Use Tooling (A) in order to remove filter assembly (1) .
Disconnect tube assemblies (2) .
Remove bolts (3) in order to remove fuel filter base assembly (4) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 2 g01034596
Install fuel filter base assembly (4) and install bolts (3) .
Connect tube assemblies (2) .
Install filter assembly (1) .
Caterpillar parts catalog:
Parts harness Caterpillar catalog:
 1957336
HARNESS AS-ENGINE
 
120H, 135H, 3126B, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
 
120H, 135H, 3126B, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
 1955663
HARNESS AS-LIGHTING
 
M313C, M313D, M315C, M315D, M316C, M316D, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH, M325C MH
 
M313C, M313D, M315C, M315D, M316C, M316D, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH, M325C MH
 2010898
HARNESS AS-LIGHTING
 
M313C, M313D, M315C, M315D, M316C, M316D, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH, M325C MH, M325D L MH, M325D MH, M330D
 
M313C, M313D, M315C, M315D, M316C, M316D, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH, M325C MH, M325D L MH, M325D MH, M330D
 2151182
HARNESS AS-RADIO
 
320C, 322C, 325C, 330C, 330C L, 345B II, 365B, 365B II, 385B, 5090B, 938G, 938G II, 938H, 950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT38G, M325C MH
 
320C, 322C, 325C, 330C, 330C L, 345B II, 365B, 365B II, 385B, 5090B, 938G, 938G II, 938H, 950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT38G, M325C MH
 3179128
HARNESS AS-BOX
 
325B L, 325C, 325D MH, 330B L, 330C MH, 330D MH, 345B, 345B II MH, 345C MH, 365B, 365B II, 365C L MH, 375 L, 385C L MH, M325B, M325C MH, M325D L MH, M325D MH, M330D, W330B, W345B II, W345C MH
 
325B L, 325C, 325D MH, 330B L, 330C MH, 330D MH, 345B, 345B II MH, 345C MH, 365B, 365B II, 365C L MH, 375 L, 385C L MH, M325B, M325C MH, M325D L MH, M325D MH, M330D, W330B, W345B II, W345C MH
 1526974
HARNESS AS-LIGHTING
 
325B L, 330B L, M325C MH, M325D L MH, M325D MH
 
325B L, 330B L, M325C MH, M325D L MH, M325D MH
 2354212
HARNESS AS-WIRING
 
M325C MH
 
M325C MH
 2409635
HARNESS AS-WIRING
 
M325C MH
 
M325C MH
 2939315
HARNESS AS-LIGHTING
 
M325C MH, M325D L MH, M325D MH
 
M325C MH, M325D L MH, M325D MH
 2364353
HARNESS AS
 
M325C MH
 
M325C MH
 2621888
HARNESS AS-CONTROL
 
M325C MH
 
M325C MH
 2637951
HARNESS AS-PANEL
 
M325C MH
  
M325C MH
 2427052
HARNESS AS-ALARM
 
M325C MH
 
M325C MH
 2444435
HARNESS AS-PLATFORM
 
365B II
 
365B II
 2444436
HARNESS AS-AUXILIARY
 
365B II
 
365B II
 2391333
HARNESS AS-PLATFORM
 
365B II
 
365B II
 2389652
HARNESS AS-AUXILIARY
 
365B II
 
365B II
 2467914
HARNESS AS-LIGHTING
 
365B II, 365C, 365C L
  
365B II, 365C, 365C L
 2409635
HARNESS AS-WIRING
 
M325C MH
 
M325C MH
 2354212
HARNESS AS-WIRING
 
M325C MH
 
M325C MH
 2354210
HARNESS AS-WIRING
 
M325C MH
 
M325C MH
 2633134
HARNESS AS-CHASSIS
 
M325C MH
 
M325C MH
 2601739
HARNESS AS-CHASSIS
 
M325C MH
 
M325C MH
 2387449
HARNESS AS-WIRING
 
M325C MH
 
M325C MH
 
 
