HARNESS AS-WIRING 2495179 - Caterpillar

Table 4
Required Parts of the963D    
Item    Part Number    Description    Qty    
8     304-9366     Enclosure Panel As     1    
9     304-9369     Enclosure Panel As     1    
6     8T-4193     Bolt     4    
7     198-4780     Hard Washer     4    Procedure for Installing New Panels
Remove the engine enclosure.ReferenceRefer to Disassembly and Assembly, KENR5171, "Engine Enclosure - Remove" for instructions on removing the engine enclosure on a 953D.ReferenceRefer to Disassembly and Assembly, KENR6063, "Engine Enclosure - Remove" for instructions on removing the engine enclosure on a 963D.
Illustration 9 g02083793
Remove seal (2) .
Illustration 10 g02106634
Remove rear brackets (10). Discard rear brackets (10) .
Complete Steps 4.a through 4.b for 953D machines.
Illustration 11 g02106638
Right frame assembly for the 953D (11) 14.25 mm (0.561 inch) hole (U) 169 mm (6.65 inch) (V) 109 mm (4.29 inch) (W) 110.5 mm (4.35 inch) (X) 203.5 mm (8.01 inch)
Drill holes (11) in the right frame assembly. Tap holes (11) with a M16 x 2 tap. Refer to Illustration 11 for the location of holes (11) .
Illustration 12 g02106640
Left frame assembly for the 953D (12) 14.25 mm (0.561 inch) hole (Y) 50 mm (1.97 inch) (Z) 256 mm (10.09 inch) (AB) 112 mm (4.41 inch)
Drill holes (12) in the left frame assembly. Tap holes (12) with a M16 x 2 tap. Refer to Illustration 12 for the location of holes (12) .
Complete Steps 5.a through 5.b for 963D machines.
Illustration 13 g02106642
Right frame assembly for the 963D (13) 14.25 mm (0.561 inch) hole (AC) 297 mm (11.69 inch) (AD) 225 mm (8.86 inch) (AE) 138.3 mm (5.44 inch) (AF) 263.3 mm (10.37 inch)
Drill holes (13) in the right frame assembly. Tap holes (13) with a M16 x 2 tap. Refer to Illustration 13 for the location of holes (13) .
Illustration 14 g02106644
Left frame assembly for the 963D (14) 14.25 mm (0.561 inch) hole (AG) 47 mm (1.85 inch) (AH) 292.3 mm (11.51 inch) (AJ) 116.3 mm (4.58 inch)
Drill holes (14) in the left frame assembly. Tap holes (14) with a M16 x 2 tap. Refer to Illustration 14 for the location of holes (14) .
Assemble seal (2) to the engine enclosure.
Illustration 15 g02107714
Centering the engine enclosures with the cabSpacing should be equal distance on both sides of the machine.
Illustration 16 g02107713
Example of a muffler that is not centered
Install the engine enclosure. Ensure that the engine enclosures are centered with the cab. Also, make sure that the muffler is properly adjusted.ReferenceRefer to Disassembly and Assembly, KENR5171, "Engine Enclosure - Install" for instructions on installing the engine enclosure on a 953D.ReferenceRefer to Disassembly and Assembly, KENR6063, "Engine Enclosure - Install" for instructions on installing the engine enclosure on a 963D.