HARNESS AS-WIRING 2537501 - Caterpillar

2537501 HARNESS AS-WIRING Caterpillar parts C11, C13

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2537501
253-7501
2537501

Weight: 0.65 pounds 0 kg.

Buy HARNESS AS-WIRING 2537501 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

239-5523 249-0093 249-8681 253-7501 240-9996 229-2919 Truck Engine Wiring Harness Fits for C11 C13 Excavator Single Injector Replace Parts

$748.44

26 Jun 2025

CN: Tree Parts Stro

239-5523 249-0093 249-8681 253-7501 240-9996 229-2919 Truck Engine Wiring Harness Fits for C11 C13 Excavator Single Injector Replace Parts
WEZHYJPAS Part Name: Truck Engine Wiring Harness || Part Number:239-5523 249-0093 249-8681 253-7501 240-9996 229-2919 || Application:Fits for C11 C13 Excavator Single Injector

$747.29

26 Jun 2025

CN: Spring PARTS ST

239-5523 249-0093 249-8681 253-7501 240-9996 229-2919 Truck Engine Wiring Harness Fits for C11 C13 Excavator Single Injector Replace Parts
ABCGTDLPAS Part Name: Truck Engine Wiring Harness || Part Number:239-5523 249-0093 249-8681 253-7501 240-9996 229-2919 || Application:Fits for C11 C13 Excavator Single Injector

$734.83

26 Jun 2025

CN: Lawn Mower Part

239-5523 249-0093 249-8681 253-7501 240-9996 229-2919 Truck Engine Wiring Harness Fits for C11 C13 Excavator Single Injector Replace Parts
GevLtty Part Name: Truck Engine Wiring Harness || Part Number:239-5523 249-0093 249-8681 253-7501 240-9996 229-2919 || Application:Fits for C11 C13 Excavator Single Injector

Show more prices Caterpillar parts

This part in 1 request: Show. This information for suppliers only!

#1206946 253-7501

2023-09-14

Number on catalog scheme: 4

Caterpillar 2537501 Parts scheme HARNESS AS-WIRING

For full view, you need register

Compatible equipment models: 2537501:

TRUCK ENGINE C11 C13 Caterpillar

Information:

Illustration 1 g06262353
Schematic of the transmission lockup clutch solenoid
This diagnostic trouble code is associated with the transmission lockup clutch solenoid. The FMI 3 means that the ECM has determined that the voltage of the solenoid circuit is above normal.The possible causes of the diagnostic trouble code are listed:
The solenoid has failed
The energize circuit of the solenoid is shorted to the +battery circuit
The ECM has failed. This is unlikelyNote: The following test procedure may create other diagnostic trouble codes. Ignore these created diagnostic trouble codes and clear these diagnostic trouble codes when the original diagnostic trouble code has been corrected. Ensure that the diagnostic trouble code of SPN 740 FMI 3 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.System Response:The solenoid is engaged in a direct drive state.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J1-62 (wire 705-PK(Pink)) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-62 (705-PK(Pink)) and the circuit that has a low resistance measurement.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK IF THE DIAGNOSTIC TROUBLE CODE IS STILL ACTIVE.
Inspect