3068777 HARNESS AS-CHASSIS Caterpillar parts
320D, 320D FM, 320D GC, 320D L, 323D L
Rating:
Alternative (cross code) number:
CA3068777
306-8777
3068777
CA3068777
306-8777
3068777
Weight: 39 pounds 17 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Chassis Harness 306-8777 3068777 Fikowjs Compatible for CAT C6.4 Engine 320D 323D 320DGC 323DL 320DL 320DFM Excavator
Fikowjs TIP: Please purchase according to the old part number, appearance is not able to judge the accuracy of the product. || Product Name:Chassis harness || Product Number:306-8777 3068777 || Application: Compatible for CAT C6.4 Engine 320D 323D 320DGC 323DL 320DL 320DFM Excavator || NOTE: There are many kinds of products in Fikowjs parts, if you can't find the part number you need, please consult us, we will reply soon!
Fikowjs TIP: Please purchase according to the old part number, appearance is not able to judge the accuracy of the product. || Product Name:Chassis harness || Product Number:306-8777 3068777 || Application: Compatible for CAT C6.4 Engine 320D 323D 320DGC 323DL 320DL 320DFM Excavator || NOTE: There are many kinds of products in Fikowjs parts, if you can't find the part number you need, please consult us, we will reply soon!
IMIFAFTAbT 306-8777 3068777 CA3068777 Chassis harness Fits for Caterpillar CAT C6.4 Engine 320D 323D 320DGC 323DL 320DL 320DFM Excavator
IMIFAFTAbT Product Name: 306-8777 3068777 CA3068777 Chassis harness || Part number: 306-8777 3068777 CA3068777 || Fits for Caterpillar CAT C6.4 Engine 320D 323D 320DGC 323DL 320DL 320DFM Excavator || 1 PCS Chassis harness || Note: Please confirm that the product shown in the part number is what you need. If you cannot confirm you can leave us a message and provide your engine serial number and nameplate
IMIFAFTAbT Product Name: 306-8777 3068777 CA3068777 Chassis harness || Part number: 306-8777 3068777 CA3068777 || Fits for Caterpillar CAT C6.4 Engine 320D 323D 320DGC 323DL 320DL 320DFM Excavator || 1 PCS Chassis harness || Note: Please confirm that the product shown in the part number is what you need. If you cannot confirm you can leave us a message and provide your engine serial number and nameplate
Chassis Harness 306-8777 3068777 Suitable for CAT C6.4 Engine 320D 323D 320DGC 323DL 320DL 320DFM Excavator Electronic Injection Engine
OfkZynodor Part Name:Chassis Harness || Part Number:306-8777 3068777 || Application:Suitable for CAT C6.4 Engine 320D 323D 320DGC 323DL 320DL 320DFM Excavator Electronic Injection Engine || Please make sure to carefully compare the photos and check the part numbers before making the purchase. If you are unable to confirm your engine model or part number, please leave us a message and we will assist you in confirming that the product you purchase is the one you need. || Your order is not merely a single purchase but the beginning of a cooperative journey, aiming to ensure the safe and smooth operation of your vehicle. We are proud to offer you reliable precision engineering components and unparalleled services.
OfkZynodor Part Name:Chassis Harness || Part Number:306-8777 3068777 || Application:Suitable for CAT C6.4 Engine 320D 323D 320DGC 323DL 320DL 320DFM Excavator Electronic Injection Engine || Please make sure to carefully compare the photos and check the part numbers before making the purchase. If you are unable to confirm your engine model or part number, please leave us a message and we will assist you in confirming that the product you purchase is the one you need. || Your order is not merely a single purchase but the beginning of a cooperative journey, aiming to ensure the safe and smooth operation of your vehicle. We are proud to offer you reliable precision engineering components and unparalleled services.
This part in 2 request:
Show.
This information for suppliers only!
2018-02-14
2017-07-06
Number on catalog scheme:
27
For full view, you need register
Compatible equipment models: 3068777:
Information:
Sensor (LIDAR) Inspect
Rotating Parts Hazard! Prior to cleaning the Lidar, ensure that the Lidar is stopped and the engine start switch is in the OFF position. Rotating objects could cause serious injury. Read and follow the Operation and Maintenance Manual for information on operating the engine start switch.
Ensure that the machine key switch is in the OFF position.
Rotate head (1) gently by hand.Note: Head should rotate freely. There should be no bearing noise or rotating resistance. If there is resistance or bearing noise, turn the machine key switch to the ON position and allow LIDAR to spin for several minutes. If noise or spinning resistance persists, then replace sensor.Before proceeding with inspection or cleaning, ensure that the machine key switch is in the OFF position.
Illustration 1 g06203266
Ensure that the mounting bolts are tight.
Ensure that both ground straps are securely fastened.
Ensure that isolation mounts are flexible and not cracked.
Inspect IMU is straight and level.
Inspect electrical connections are tight, secure, and free of cracks and corrosion.
Check the LIDAR for an excessive amount of mud or other materials.Note: When the LIDAR is covered with mud or other debris, clean the LIDAR and remove debris.
If the LIDAR has been moved, removed, or replaced, then refer to Operation and Maintenance Manual, "Calibrations for Maintenance"Autonomy Camera Inspect
Illustration 2 g06203267
Check cameras for proper alignment. Check for paint pen marks to verify that all cameras are positioned correctly.
If paint pen markings are not aligned or are not visible, then verify camera alignment using the Operator Control Station (OCS). Refer to Operation and Maintenance Manual, "Camera - Adjust" for proper camera alignment.Sensor (LIDAR) and Cameras Cleaning Instructions
Rotating Parts Hazard! Prior to cleaning the Lidar, ensure that the Lidar is stopped and the engine start switch is in the OFF position. Rotating objects could cause serious injury. Read and follow the Operation and Maintenance Manual for information on operating the engine start switch.
Use a damp cloth with non-abrasive soap to clean the glass of the LIDAR sensors and cameras.
Perform a perception system calibration if glass is scratched. Refer to Special Instruction, REHS8845, "Autonomous Calibration Procedure".
Rotating Parts Hazard! Prior to cleaning the Lidar, ensure that the Lidar is stopped and the engine start switch is in the OFF position. Rotating objects could cause serious injury. Read and follow the Operation and Maintenance Manual for information on operating the engine start switch.
Ensure that the machine key switch is in the OFF position.
Rotate head (1) gently by hand.Note: Head should rotate freely. There should be no bearing noise or rotating resistance. If there is resistance or bearing noise, turn the machine key switch to the ON position and allow LIDAR to spin for several minutes. If noise or spinning resistance persists, then replace sensor.Before proceeding with inspection or cleaning, ensure that the machine key switch is in the OFF position.
Illustration 1 g06203266
Ensure that the mounting bolts are tight.
Ensure that both ground straps are securely fastened.
Ensure that isolation mounts are flexible and not cracked.
Inspect IMU is straight and level.
Inspect electrical connections are tight, secure, and free of cracks and corrosion.
Check the LIDAR for an excessive amount of mud or other materials.Note: When the LIDAR is covered with mud or other debris, clean the LIDAR and remove debris.
If the LIDAR has been moved, removed, or replaced, then refer to Operation and Maintenance Manual, "Calibrations for Maintenance"Autonomy Camera Inspect
Illustration 2 g06203267
Check cameras for proper alignment. Check for paint pen marks to verify that all cameras are positioned correctly.
If paint pen markings are not aligned or are not visible, then verify camera alignment using the Operator Control Station (OCS). Refer to Operation and Maintenance Manual, "Camera - Adjust" for proper camera alignment.Sensor (LIDAR) and Cameras Cleaning Instructions
Rotating Parts Hazard! Prior to cleaning the Lidar, ensure that the Lidar is stopped and the engine start switch is in the OFF position. Rotating objects could cause serious injury. Read and follow the Operation and Maintenance Manual for information on operating the engine start switch.
Use a damp cloth with non-abrasive soap to clean the glass of the LIDAR sensors and cameras.
Perform a perception system calibration if glass is scratched. Refer to Special Instruction, REHS8845, "Autonomous Calibration Procedure".
Caterpillar parts catalog:
Parts harness Caterpillar catalog:
311D LRR, 311F LRR, 312D, 312D L, 312D2, 314D CR, 314D LCR, 315D L, 318D2 L, 319D L, 319D LN, 320D, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325D,...
320D, 323D L
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
3640229
HARNESS AS-CONTROL
320D, 320D L, 323D L
320D, 320D L, 323D L
320D, 320D GC, 320D L, 320D LN, 323D L
3068362
HARNESS AS-CONTROL
320D, 345C
320D, 345C
3068502
HARNESS AS-SENSOR
320D, 320D L
320D, 320D L
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 323D L
3025688
HARNESS AS-SWITCH
320D FM RR
320D FM RR
3347972
HARNESS AS-CHASSIS
320D FM RR
320D FM RR
3191359
HARNESS AS-PANEL
320D, 320D FM, 320D FM RR
320D, 320D FM, 320D FM RR
2832971
HARNESS AS-PANEL
320D, 320D FM, 320D FM RR
320D, 320D FM, 320D FM RR
3078199
HARNESS AS-FRONT LIGHTING
320D FM RR
320D FM RR
3025676
HARNESS AS-WIRING
320D FM RR
320D FM RR
320D, 320D FM, 320D L, 320D2 L, 323D L, 323D LN
2580729
HARNESS AS-LIGHTING
320C, 320D, 320D L, 330D
320C, 320D, 320D L, 330D
320D, 320D FM, 320D GC, 323D L