3423034 HARNESS AS-CHASSIS Caterpillar parts
315D L, 319D L, 319D LN
Rating:
Alternative (cross code) number:
CA3423034
342-3034
3423034
CA3423034
342-3034
3423034
Weight: 30 pounds 13 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Technical Precision Replacement for EZGO/Cushman/TEXTRON 3423-034
Technical Precision Replacement For EZGO / CUSHMAN / TEXTRON 3423-034 || Unit per sale:1
Technical Precision Replacement For EZGO / CUSHMAN / TEXTRON 3423-034 || Unit per sale:1
Number on catalog scheme:
40
For full view, you need register
Information:
START BY:a. remove timing gear coverb. remove valve lifters 1. Remove turbocharger drain tube (1) from the flywheel housing. Remove two studs (2) with tool (C). 2. Turn the engine with tool (B) until the bolts in camshaft rear gear (3) are visible. Remove the four bolts.
Tooling (A) must be used to prevent the loss of timing of the rear balance weight gear and to keep the rear camshaft gear in place when the camshaft is removed.
3. Turn the engine until the "V" marks on the front timing gears are in alignment. Install tooling (A) through the flywheel housing and into gear (3).4. Tighten tooling (A) evenly to free the rear camshaft gear from the camshaft. 5. Remove two bolts (4) and plate (5).
Be careful not to cause damage to the camshaft bearings as the camshaft is removed.
6. Remove the camshaft and gear from the cylinder block. 7. If necessary, remove the camshaft gear with tool (D). Remove the dowel on the taper end of the camshaft with tooling (E).Install Camshaft
Make sure the key for gear (1) is in position on camshaft (2) before gear (1) in installed.1. Heat gear (1) to a maximum temperature of 600°F (315°C). Install gear (1) on camshaft (2).2. Install pin (3) until it is extended 8.76 0.25 mm (.345 .010 in.) from the end of the camshaft. 3. Put clean engine oil on the lobes and journals of camshaft (2) and on the camshaft bearings in the cylinder block. Install the camshaft with the "V" mark on gear (1) in alignment with the "V" mark on gear (5).4. Install plate (4) and the bolts. 5. Loosen bolts (6) of tooling (A) to align pin (3) and gear (7). Install one bolt in the gear to hold it in position. Remove tooling (A).6. Turn the engine with tool (B) until all of bolts (9) are installed. Tighten bolts (9) evenly to a torque of 25 4 N m (20 3 lb.ft.). Tighten the bolts again to a torque of 25 4 N m (18 3 lb.ft.).7. Check the camshaft end play with tool (D). End play must be 0.10 to 0.25 mm (.004 to .010 in.).8. Install two studs (8) with tool (C) until they are extended 25.4 1.5 mm (1.00 .06 in.) from the surface of the flywheel housing.9. Install the oil drain tube for the turbocharger.END BY:a. install valve liftersb. install timing gear cover
Tooling (A) must be used to prevent the loss of timing of the rear balance weight gear and to keep the rear camshaft gear in place when the camshaft is removed.
3. Turn the engine until the "V" marks on the front timing gears are in alignment. Install tooling (A) through the flywheel housing and into gear (3).4. Tighten tooling (A) evenly to free the rear camshaft gear from the camshaft. 5. Remove two bolts (4) and plate (5).
Be careful not to cause damage to the camshaft bearings as the camshaft is removed.
6. Remove the camshaft and gear from the cylinder block. 7. If necessary, remove the camshaft gear with tool (D). Remove the dowel on the taper end of the camshaft with tooling (E).Install Camshaft
Make sure the key for gear (1) is in position on camshaft (2) before gear (1) in installed.1. Heat gear (1) to a maximum temperature of 600°F (315°C). Install gear (1) on camshaft (2).2. Install pin (3) until it is extended 8.76 0.25 mm (.345 .010 in.) from the end of the camshaft. 3. Put clean engine oil on the lobes and journals of camshaft (2) and on the camshaft bearings in the cylinder block. Install the camshaft with the "V" mark on gear (1) in alignment with the "V" mark on gear (5).4. Install plate (4) and the bolts. 5. Loosen bolts (6) of tooling (A) to align pin (3) and gear (7). Install one bolt in the gear to hold it in position. Remove tooling (A).6. Turn the engine with tool (B) until all of bolts (9) are installed. Tighten bolts (9) evenly to a torque of 25 4 N m (20 3 lb.ft.). Tighten the bolts again to a torque of 25 4 N m (18 3 lb.ft.).7. Check the camshaft end play with tool (D). End play must be 0.10 to 0.25 mm (.004 to .010 in.).8. Install two studs (8) with tool (C) until they are extended 25.4 1.5 mm (1.00 .06 in.) from the surface of the flywheel housing.9. Install the oil drain tube for the turbocharger.END BY:a. install valve liftersb. install timing gear cover
Caterpillar parts catalog:
Parts harness Caterpillar catalog:
2756842
HARNESS AS-CONTROL
312D, 312D L, 315D L, 319D L, 319D LN, 320D, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 L, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324D LN, 325D, 325D L, 329D, 329D L, 329D LN, 330D L, ...
312D, 312D L, 315D L, 319D L, 319D LN, 320D, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 L, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324D LN, 325D, 325D L, 329D, 329D L, 329D LN, 330D L, ...
2992838
HARNESS AS-VALVE
315D L, 318D2 L, 319D L, 319D LN
315D L, 318D2 L, 319D L, 319D LN
2677672
HARNESS AS-WIRING
311D LRR, 312D, 312D L, 315D L, 319D, 319D L, 319D LN, 320D, 320D L, 320D LN, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324D LN, 325D, 325D L, 329D, 329D L, 329D LN, 330D L, 330D LN, 336D, 336D...
311D LRR, 312D, 312D L, 315D L, 319D, 319D L, 319D LN, 320D, 320D L, 320D LN, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324D LN, 325D, 325D L, 329D, 329D L, 329D LN, 330D L, 330D LN, 336D, 336D...
2992701
HARNESS AS-CAB
311D LRR, 312D, 312D L, 315D L, 319D L, 345D, 345D L, 349D, 349D L
311D LRR, 312D, 312D L, 315D L, 319D L, 345D, 345D L, 349D, 349D L
3279998
HARNESS AS-AUXILIARY
311D LRR, 312D, 312D L, 312D2, 315D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 321D LCR, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325D, 325D L, 325D ...
311D LRR, 312D, 312D L, 312D2, 315D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 321D LCR, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325D, 325D L, 325D ...
2677705
HARNESS AS-VALVE
315D L, 319D L, 319D LN
315D L, 319D L, 319D LN
2832914
HARNESS AS-RADIO
311D LRR, 315D L, 320D, 320D LRR, 320D RR, 320D2 L, 323D L, 323D LN, 324D, 324D L, 325D L, 329D L, 330D L, 336D, 336D L, 336D2, 345C, 345D L, 349D L
311D LRR, 315D L, 320D, 320D LRR, 320D RR, 320D2 L, 323D L, 323D LN, 324D, 324D L, 325D L, 329D L, 330D L, 336D, 336D L, 336D2, 345C, 345D L, 349D L
3068456
HARNESS AS-WIRING
315D L, 319D, 319D L
315D L, 319D, 319D L
3423122
HARNESS AS-POWER
312D L, 315D L, 319D L, 319D LN, 324D L, 329D, 336D, 345D L, 349D L
312D L, 315D L, 319D L, 319D LN, 324D L, 329D, 336D, 345D L, 349D L
3423242
HARNESS AS-CONTROL
314D CR, 314D LCR
314D CR, 314D LCR
3423042
HARNESS AS-CAB
314D CR, 314D LCR, 321D LCR
314D CR, 314D LCR, 321D LCR
3508121
HARNESS AS-SOLENOID
314D CR, 314D LCR
314D CR, 314D LCR
3050318
HARNESS AS-SENSOR
314D CR, 314D LCR, 321D LCR, 328D LCR
314D CR, 314D LCR, 321D LCR, 328D LCR
3423284
HARNESS AS-SENSOR
314D LCR
314D LCR
3423056
HARNESS AS-POWER
314D LCR
314D LCR
3423130
HARNESS AS-SOLENOID
315D L, 319D L, 319D LN
315D L, 319D L, 319D LN
3423129
HARNESS AS-SOLENOID
315D L, 319D L, 319D LN
315D L, 319D L, 319D LN
3423132
HARNESS AS-PUMP
315D L, 319D L, 319D LN
315D L, 319D L, 319D LN
3508043
HARNESS AS-CHASSIS
315D L, 319D L, 319D LN
315D L, 319D L, 319D LN
3508487
HARNESS AS-CAB
315D L, 319D L, 319D LN
315D L, 319D L, 319D LN
3508466
HARNESS AS-CHASSIS
315D L, 319D L, 319D LN
315D L, 319D L, 319D LN