3508442 HARNESS AS-CAB Caterpillar parts
336E L, 349E L, 349E L VG
Rating:
Alternative (cross code) number:
CA3508442
350-8442
3508442
CA3508442
350-8442
3508442
Weight: 14 pounds 6 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CoCocina 3Pcs Memory Card Storage Box Case Organizer for Sd Card Tf Card Memory Stick
CoCocina A good partner for photographer || With this storage box, you can organize your memory cards so well || Capacity: 1 x memory Card, 6 x TF Card, 1 x Memory Stick || 3 x Card Case || Only card case, memory cards not included)
CoCocina A good partner for photographer || With this storage box, you can organize your memory cards so well || Capacity: 1 x memory Card, 6 x TF Card, 1 x Memory Stick || 3 x Card Case || Only card case, memory cards not included)
Number on catalog scheme:
24
For full view, you need register
Information:
Installation Procedure
Table 6
Required Tools
Tool Part Number Part Description Qty
A (1) 9U-6198 Crankshaft Turning Tool 1
A (2) 5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C 227-4390 E12 Torx Socket 1
D 8T-3052 Degree Wheel 1
( 1 ) The Crankshaft Turning Tool is used on the front pulley.
( 2 ) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all of the components.
Apply clean engine oil to the cylinder bore, piston rings, outer surface of the piston and the bearing shells for the connecting rod.Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance". Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 12 g02013213
Install Tooling (B) onto piston (4) .Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin.Note: Do not damage the finished surface of the crankshaft pin.
Illustration 13 g02447296
Install connecting rod cap (2) onto connecting rod (1) .Note: Ensure that dot punched number in Position (X) on connecting rod cap (2) matches dot punched number in Position (X) on connecting rod (1). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old bolts in order to secure the connecting rod cap.
Install new bolts (3) to connecting rod (1). Use Tooling (C) in order to tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) and Tooling (D) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft in order to ensure that there is no binding.
Repeat Step 2 through
Table 6
Required Tools
Tool Part Number Part Description Qty
A (1) 9U-6198 Crankshaft Turning Tool 1
A (2) 5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C 227-4390 E12 Torx Socket 1
D 8T-3052 Degree Wheel 1
( 1 ) The Crankshaft Turning Tool is used on the front pulley.
( 2 ) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all of the components.
Apply clean engine oil to the cylinder bore, piston rings, outer surface of the piston and the bearing shells for the connecting rod.Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance". Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 12 g02013213
Install Tooling (B) onto piston (4) .Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin.Note: Do not damage the finished surface of the crankshaft pin.
Illustration 13 g02447296
Install connecting rod cap (2) onto connecting rod (1) .Note: Ensure that dot punched number in Position (X) on connecting rod cap (2) matches dot punched number in Position (X) on connecting rod (1). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old bolts in order to secure the connecting rod cap.
Install new bolts (3) to connecting rod (1). Use Tooling (C) in order to tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) and Tooling (D) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft in order to ensure that there is no binding.
Repeat Step 2 through
Caterpillar parts catalog:
Parts harness Caterpillar catalog:
3690168
HARNESS AS-SENSOR
320E L, 320E LN, 323E L, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E HVG, 336E L, 336E LN, 336F L
320E L, 320E LN, 323E L, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E HVG, 336E L, 336E LN, 336F L
3621505
HARNESS AS-SENSOR
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 730C, 980K, 980K HLG, 980M, 982M, C13, CX31-C13I
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 730C, 980K, 980K HLG, 980M, 982M, C13, CX31-C13I
3508227
HARNESS AS-CHASSIS
336E, 336E HVG, 336E L, 336E LN, 336F L
336E, 336E HVG, 336E L, 336E LN, 336F L
3587858
HARNESS AS-ENGINE
349E L, 349E L VG, C13, C13 XQ350, CX31-C13I
349E L, 349E L VG, C13, C13 XQ350, CX31-C13I
3606291
HARNESS AS-PLATFORM
312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E HVG, 336E L, 336E LN, 336F L, 349E, 349E L, 349E L HVG, 349E L ...
312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E HVG, 336E L, 336E LN, 336F L, 349E, 349E L, 349E L HVG, 349E L ...
3280306
HARNESS AS-SOLENOID
336E, 336E L, 336E LN, 336F L, 568 FM LL
336E, 336E L, 336E LN, 336F L, 568 FM LL
3366347
HARNESS AS-CONTROL
336E, 336E H, 336E L, 336E LH, 336E LN, 336F L
336E, 336E H, 336E L, 336E LH, 336E LN, 336F L
3508314
HARNESS AS-WIRING
336E L
336E L
3640256
HARNESS AS-LIGHTING
349E, 349E L, 349E L VG, 349F L
349E, 349E L, 349E L VG, 349F L
3508136
HARNESS AS-LIGHTING
336E, 336E L, 349E, 374F L, 390F L
336E, 336E L, 349E, 374F L, 390F L
3422843
HARNESS AS-LIGHTING
336E L
336E L
3606177
HARNESS AS-CHASSIS
336E, 336E L
336E, 336E L
3279940
HARNESS AS-CHASSIS
336E L
336E L
3690129
HARNESS AS-CONTROL
336E, 336E H, 336E L, 336E LH, 336E LN, 336F L
336E, 336E H, 336E L, 336E LH, 336E LN, 336F L
3366348
HARNESS AS-CONTROL
336E L, 336E LN
336E L, 336E LN
3508314
HARNESS AS-WIRING
336E L
336E L
3280376
HARNESS AS-CEM
336E L
336E L
4538722
HARNESS AS-CAB
336E L, 336F L
336E L, 336F L
3422907
HARNESS AS-CAB
336E L
336E L
3422906
HARNESS AS-CAB
336E L
336E L
3280104
HARNESS AS-CAB
336E L
336E L