3826282 HARNESS AS-WORK TOOL Caterpillar parts
HM415B
Rating:
Alternative (cross code) number:
CA3826282
382-6282
3826282
CA3826282
382-6282
3826282
Weight: 1 pounds 0 kg.
MULCHING HEAD,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$17.98
18 Dec 2018
Magnum Tuning: Magnum Tuning
PERFORMANCE SPARK PLUG Mercruiser 140 (To 3826282) Stern Drive 4 cyl GM V8 All * S18LR15ZCTRZ83
1. Higher HP and torque by up to 3 % || 2. increased economy by up to 5% || 3. 360° Firing Technology || 4. Improved acceleration by up to 15 % || 5. 25,000 miles - 40,000 km duration
1. Higher HP and torque by up to 3 % || 2. increased economy by up to 5% || 3. 360° Firing Technology || 4. Improved acceleration by up to 15 % || 5. 25,000 miles - 40,000 km duration
$69.99
18 Dec 2018
Magnum Tuning: Magnum Tuning
SET OF 4 PERFORMANCE SPARK PLUG Mercruiser 140 (To 3826282) Stern Drive 4 cyl GM V8 All XD249LR15ZCTRZ83
1. Higher HP and torque by up to 3 % || 2. increased economy by up to 5% || 3. 360° Firing Technology || 4. Improved acceleration by up to 15 % || 5. 5 UP TO 600 HOUR LIFESPAN
1. Higher HP and torque by up to 3 % || 2. increased economy by up to 5% || 3. 360° Firing Technology || 4. Improved acceleration by up to 15 % || 5. 5 UP TO 600 HOUR LIFESPAN
$102.99
02 May 2017
Magnum Tuning: Magnum Tuning
SET OF 6 PERFORMANCE SPARK PLUG Mercruiser 140 (To 3826282) Stern Drive 4 cyl GM V8 All * QY249LR15ZCTRZ83
This part in 8 request:
Show.
This information for suppliers only!
2024-10-09
2024-02-04
2023-06-20
2021-12-13
2021-09-28
2020-03-14
2019-04-01
2018-09-27
Number on catalog scheme:
2
For full view, you need register
Compatible equipment models: 3826282:
Information:
Procedure for the Installation of the New Oil Pan Gasket
Note: Some Machines that are listed above may not have the plate located between the oil pan and the engine block. In these instances, only one replacement oil pan gasket will be used. The installation procedure of the gasket remains the same and the Steps involving the plate are not used.
Table 1
Required Parts
Qty Part Number Part Description
1 141-5831 Silicone Sealant
1 1Y-3904 Adhesive
6 1A-2029 Bolts
6 5M-2894 Hard Washers
1 or 2 (1) 353-5065 Oil Pan Gasket
( 1 ) Some Machines that are listed above may not have the plate located between the oil pan and the engine block. In these instances, only one replacement oil pan gasket will be used.
Drain the engine oil into a suitable container.
Remove the bolts with washers that secure the engine oil pan to the engine block.
Remove the engine oil pan.
Remove the suction tube, bracket, and discharge tube.
Remove the plate with both of the gaskets that are located on both sides of the plate.
Clean the sealing surface of the oil pan, plate, and engine block thoroughly.
Illustration 1 g02476831
Location of the adhesive on the plate (1) Plate
Apply 1Y-3904 Adhesive onto the side of the plate that will contact the engine block. Refer to Illustration 1 for the proper location of the adhesive.
Illustration 2 g02476897
Location of sealant at the joints of the gasket (2) 141-5831 Silicone Sealant
Install one of the new gaskets onto the side of the plate that will contact the engine block. Apply 141-5831 Silicone Sealant at the puzzle joints of the new gasket. Refer to Illustration 2 for the proper location of the sealant.
Illustration 3 g02477451
(A) Location of T-joints
Apply a 3 mm (0.11811 inch) to 5 mm (0.19685 inch) bead of 141-5831 Silicone Sealant at the T-joints of the engine block. Refer to Illustration 4 for the proper location of the sealant.Note: All of the joints must be assembled within 10 minutes of sealant application. After 10 minutes the sealant will begin to harden, and the performance of the sealant is compromised.
Illustration 4 g02477309
(3) 1A-2029 Bolt (4) 5M-2894 Hard Washer
Install plate with gasket onto the engine block. Use location 1 and 2, 3 and 4, or 5 and 6 with bolts (3) with washers (4) for installation.
Install the suction tube, brackets, and discharge tube.
Illustration 5 g02477177
Typical exampleLocation of sealant at the joints of the gasket
Install the new gasket onto the engine oil pan.
Install the engine oil pan with the new gasket onto the engine block. Use the bolts and the washers that were removed in Step 2.
Illustration 6 g02477317
Tighten the bolts 1 through 40 to the following torque: 40 5 N m (30 4 lb ft). Refer to Illustration 6 for the proper tightening sequence.
Illustration 7 g02477373
Retighten bolts 1 through 40 to the following torque: 47 5 N m (35 4 lb ft). Refer to Illustration
Note: Some Machines that are listed above may not have the plate located between the oil pan and the engine block. In these instances, only one replacement oil pan gasket will be used. The installation procedure of the gasket remains the same and the Steps involving the plate are not used.
Table 1
Required Parts
Qty Part Number Part Description
1 141-5831 Silicone Sealant
1 1Y-3904 Adhesive
6 1A-2029 Bolts
6 5M-2894 Hard Washers
1 or 2 (1) 353-5065 Oil Pan Gasket
( 1 ) Some Machines that are listed above may not have the plate located between the oil pan and the engine block. In these instances, only one replacement oil pan gasket will be used.
Drain the engine oil into a suitable container.
Remove the bolts with washers that secure the engine oil pan to the engine block.
Remove the engine oil pan.
Remove the suction tube, bracket, and discharge tube.
Remove the plate with both of the gaskets that are located on both sides of the plate.
Clean the sealing surface of the oil pan, plate, and engine block thoroughly.
Illustration 1 g02476831
Location of the adhesive on the plate (1) Plate
Apply 1Y-3904 Adhesive onto the side of the plate that will contact the engine block. Refer to Illustration 1 for the proper location of the adhesive.
Illustration 2 g02476897
Location of sealant at the joints of the gasket (2) 141-5831 Silicone Sealant
Install one of the new gaskets onto the side of the plate that will contact the engine block. Apply 141-5831 Silicone Sealant at the puzzle joints of the new gasket. Refer to Illustration 2 for the proper location of the sealant.
Illustration 3 g02477451
(A) Location of T-joints
Apply a 3 mm (0.11811 inch) to 5 mm (0.19685 inch) bead of 141-5831 Silicone Sealant at the T-joints of the engine block. Refer to Illustration 4 for the proper location of the sealant.Note: All of the joints must be assembled within 10 minutes of sealant application. After 10 minutes the sealant will begin to harden, and the performance of the sealant is compromised.
Illustration 4 g02477309
(3) 1A-2029 Bolt (4) 5M-2894 Hard Washer
Install plate with gasket onto the engine block. Use location 1 and 2, 3 and 4, or 5 and 6 with bolts (3) with washers (4) for installation.
Install the suction tube, brackets, and discharge tube.
Illustration 5 g02477177
Typical exampleLocation of sealant at the joints of the gasket
Install the new gasket onto the engine oil pan.
Install the engine oil pan with the new gasket onto the engine block. Use the bolts and the washers that were removed in Step 2.
Illustration 6 g02477317
Tighten the bolts 1 through 40 to the following torque: 40 5 N m (30 4 lb ft). Refer to Illustration 6 for the proper tightening sequence.
Illustration 7 g02477373
Retighten bolts 1 through 40 to the following torque: 47 5 N m (35 4 lb ft). Refer to Illustration
Caterpillar parts catalog:
Parts harness Caterpillar catalog:
HM312, HM315, HM415B, PC206, PC310B, SG16B, SW345B, SW60, T9B
3826281
HARNESS AS-WORK TOOL
HM415B
HM415B
3826281
HARNESS AS-WORK TOOL
HM415B
HM415B
3959921
HARNESS AS-HEATER & AIR COND
MH3037, MH3049, MH3059
MH3037, MH3049, MH3059
3955422
HARNESS AS-SOLENOID
MH3037
MH3037
3959663
HARNESS-MONITOR
MH3037, MH3049, MH3059
MH3037, MH3049, MH3059
3803081
HARNESS AS-FRONT
12M 3 AWD, 140M 3 AWD, 160M 3 AWD
12M 3 AWD, 140M 3 AWD, 160M 3 AWD
3803042
HARNESS AS-SENSOR
12M 3 AWD, 140M 3 AWD, 160M 3 AWD
12M 3 AWD, 140M 3 AWD, 160M 3 AWD
3798366
HARNESS AS-SWITCH
336E HVG, 349E L HVG
336E HVG, 349E L HVG
3798365
HARNESS AS-CAB
336E HVG, 349E L HVG
336E HVG, 349E L HVG
4181911
HARNESS AS-CAB
336E HVG, 349E L HVG
336E HVG, 349E L HVG
4181910
HARNESS AS-CAB
336E HVG, 349E L HVG
336E HVG, 349E L HVG
3866097
HARNESS AS-CAB
336E HVG
336E HVG
3798367
HARNESS AS-CAB
336E HVG
336E HVG