AVSPARE.COM
parts catalog

HARNESS AS-VALVE 3905124 - Caterpillar



3905124 HARNESS AS-VALVE Caterpillar parts HARNESS
Rating:
81
Alternative (cross code) number:
CA3905124
390-5124
3905124
Caterpillar 3905124 HARNESS AS-VALVE
Weight: 0.80 pounds 0 kg.

Buy HARNESS AS-VALVE 3905124 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 6
 
  For full view, you need register

Information:


Fuel injection lines MUST only be used once. Discard all fuel injection lines after use.
Fuel Line Removal and Installation Procedures
Required Parts
Table 1
Fuel Line Part Number     Description     Replacement Kit Part Number     Description    
292-3739     Fuel Line Tube Assembly for Pump line     310-6027     Fuel Lines Kit    
284-9405     Fuel Line Tube Assembly for Line 1     310-6029     Fuel Lines Kit    
284-9407     Fuel Line Tube Assembly for Line 6     352-8533     Fuel Lines Kit    
284-9406     Fuel Line Tube Assembly for Line 5     352-8532     Fuel Lines Kit    
310-8219     Clamp     347-5556     Fuel Lines Kit    Replace the removed high-pressure fuel line with the corresponding Fuel Lines Kit. The clamp, the grommet, and the new fuel line that is supplied with the Fuel Lines Kit must be used as the replacements for the old parts. Refer to Table 1.Note: Do not reuse the old clamp, the old grommet, and the old fuel line.Removal Procedure
Turn the fuel supply to the OFF position.
Disconnect the battery. Refer to Operation and Maintenance Manual, "Battery or Battery Cable - Disconnect".
Illustration 1 g01444637
Illustration 2 g01635754
Illustration 3 g01687853
Remove bolts (10) and clamps (9) at Locations (1), (2), (3), and (5). Take note of rubber grommets (8) in clamps (9) at Locations (1), (2), (3), and (5) .
Remove screw (11) and clamps (12) at Location (4). Discard the screw and the clamps. Do not reuse.
Loosen nut (7) on each end of fuel injection line (6). Remove fuel injection line (6). Repeat for the remaining fuel injection lines. Discard the fuel injection lines.Installation Procedure
Note: For installation of the bracket for Line 5, refer to Special Instruction, REHS4835.
Illustration 4 g02042205
Illustration 5 g01635754
Illustration 6 g02042206
Install a new fuel injection line (6). Hand tighten nut (7) on each end of the fuel injection line. Repeat for the remaining fuel injection lines.
Install clamps (9) at Locations (1), (2), (3), and (5). Make sure that rubber grommets (8) are placed correctly in clamps (9) at Locations (1), (2), (3), and (5). Failure to correctly place the grommet in the clamp could result in a failed fuel line. Install bolts (10) for clamps (9) hand tight.
Install the new 310-8219 Clamp (12) and screw (11) at Location (4) .Note: Ensure that the fuel injection lines are centered in the nuts prior to tightening. Do not use excessive force or bending in order to assemble the fuel injection lines.
Tighten nuts (7) at the fuel rail for the fuel injection lines to a torque of 27 3 N m (20 2 lb ft).
Tighten nuts (7) at the quill tube to a torque of 15 3 N m (135 27 lb in). Turn nuts (7) at the quill tube for an additional 60 5 degrees.
Tighten bolts (10) for clamps (9) at Locations (1), (2), (3), and (5) to a torque of 12 3 N m (105 27 lb in). Tighten screw (11)

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
963K Track-Type Loader YDR00001-UP (MACHINE) POWERED BY C7.1 Engine
963K TRACK-TYPE LOADER LBL00001-UP (MACHINE) POWERED BY C7.1 Engine


Parts harness Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.