AVSPARE.COM
parts catalog

HARNESS AS-STEERING 4557844 - Caterpillar


4557844 HARNESS AS-STEERING Caterpillar parts
Rating:
36
Alternative (cross code) number:
CA4557844
455-7844
4557844
Caterpillar 4557844 HARNESS AS-STEERING
Weight: 6 pounds 2 kg.

Buy HARNESS AS-STEERING 4557844 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 16
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     9U-6195     Valve Spring Compressor     1    Start By:
Remove the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Before you begin the removal of the valve springs, refer to Specifications, "Cylinder Head Valves" and Testing and Adjusting, "Cylinder Head - Inspect" for appropriate information on the valve springs.
Do not turn the crankshaft while the valve springs are removed.
Ensure that the piston is at the top center position.
Illustration 1 g00825744
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Use Tooling (A) to compress valve springs (1) . Remove valve keepers (2) .
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Release the pressure on Tooling (A) . Remove valve spring retainer (3) and valve springs (1) from the cylinder head.
Do not turn the crankshaft while the valve springs are removed.
Installation Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     9U-6195     Valve Spring Compressor     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00825744
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Place new valve springs (1) into position on the cylinder head.Note: Ensure that the closed damper coils are toward the cylinder head if double valve springs are used.
Install valve spring retainer (3) .
Use Tooling (A) to compress valve springs (1) .
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Install valve keepers (2) in order to lock the valve springs in position.
Release the pressure slowly on Tooling (A) . Remove Tooling (A) . Strike the top of the valves with a soft faced hammer in order to ensure that the valve keepers are properly installed.End By: Install the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
12K Motor Grader JJA00001-UP (MACHINE) POWERED BY C7 Engine
120K Motor Grader SZN00001-UP (MACHINE) POWERED BY C7 Engine
160K Motor Grader JBP00001-UP (MACHINE) POWERED BY C7 Engine
120K Motor Grader JAP00001-UP (MACHINE) POWERED BY C7 Engine
12K Motor Grader SZP00001-UP (MACHINE) POWERED BY C7 Engine
140K Motor Grader SZL00001-UP (MACHINE) POWERED BY C7 Engine
160K Motor Grader SZM00001-UP (MACHINE) POWERED BY C7 Engine
140K Motor Grader JPA00001-UP (MACHINE) POWERED BY C7 Engine
120K Series 2 Motor Grader SZS00001-UP (MACHINE) POWERED BY C7 Engine
140K Series 2 Motor Grader SZW00001-UP (MACHINE) POWERED BY C7 Engine


Parts harness Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.