HARNESS AS-WIRING 4986396 - Caterpillar

"PTO Engine RPM Set Speed Input A"
This parameter configures an input for a PTO engine rpm set speed A switch. This switch is used to control engine speed during PTO operation. The "PTO Configuration" parameter must be programmed to "Cab Switches", to "Remote Switches" or to "Remote Throttle" and the "PTO Engine RPM Set Speed A" parameter must be programmed to a valid speed.
Table 9
Alternative     Default    
"J1P1:46"     "None"    "PTO Engine RPM Speed Input B"
This parameter configures an input for a PTO engine rpm set speed B switch. This switch is used to control engine speed during PTO operation. The "PTO Configuration" parameter must be programmed to "Cab Switches", to "Remote Switches" or to "Remote Throttle" and the "PTO Engine RPM Set Speed B" parameter must be programmed to a valid speed.
Table 10
Alternatives     Default    
"J1/P1:7", "J1P1:23"     "None"    "Diagnostic Enable"
This parameter configures an input for a diagnostic enable switch. The diagnostic enable switch is used to retrieve diagnostic flash codes. Set this parameter to "J1/P1:46" if a switch is wired to this input. Set this parameter to "J1939 Body Controller", to "J1939 Cab Controller", or to "J1939 Instrument Cluster" if a J1939 message is used.
Table 11
Alternative     Default    
"J1/P1:46"
"J1939 Body Controller"
"J1939 Cab Controller"
"J1939 Instrument Cluster"     "None"    "Cruise Control On/Off Switch"
This parameter configures an input for a cruise control on/off switch. Set this parameter to "J1/P1:59" if a switch is wired to this input. Set this parameter to "J1939 Body Controller", to "J1939 Cab Controller", or to "J1939 Instrument Cluster" if a J1939 message is used.
Table 12
Alternative     Default    
"J1939 Body Controller"
"J1939 Cab Controller"
"J1939 Instrument Cluster"     "J1/P1:59"    "Cruise Control Set/Resume Switch"
This parameter configures an input for a cruise control set/resume switch. Set this parameter to "J1/P1:35 & 44" if a switch is wired to this input. Set this parameter to "J1939 Body Controller", to "J1939 Cab Controller", or to "J1939 Instrument Cluster" if a J1939 message is used.
Table 13
Alternative     Default    
"J1939 Body Controller"
"J1939 Cab Controller"
"J1939 Instrument Cluster"     "J1/P1:35 & 44"    "Cruise Control Pause Switch"
This parameter configures an input for use as a cruise control pause switch. This functionality is only available for use over a J1939 data link. This feature affects cruise control, elevated idle, and PTO operation.
Table 14
Alternative     Default    
"J1939 Body Controller"
"J1939 Cab Controller"
"J1939 Instrument Cluster"     "None"    "Clutch Pedal Position Switch"
This switch input is required for some transmission styles. A switch can be wired to this input or a J1939 message may be used as an input.
Table 15
Alternative     Default    
"J1939 Body Controller"
"J1939 Cab Controller"
"J1939 Instrument Cluster"     "J1/P1:22"    "Service Brake Pedal Position Switch #1"
This switch input is required. A switch can be wired to this input or a J1939 message may be used as an input.
Table 16
Alternative     Default    
"J1939 Body Controller"
"J1939 Cab Controller"
"J1939 Instrument Cluster"     "J1/P1:45"    "Accelerator Pedal Position"
The Input for the "Accelerator