AVSPARE.COM
parts catalog

HARNESS AS-PANEL 5089000 - Caterpillar



5089000 HARNESS AS-PANEL Caterpillar parts HARNESS
Rating:
71
Alternative (cross code) number:
CA5089000
508-9000
5089000
Caterpillar 5089000 HARNESS AS-PANEL
Weight: 1 pounds 0 kg.

Buy HARNESS AS-PANEL 5089000 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 31
 
  For full view, you need register

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
Clean all 26 head bolt holes on the cylinder block with Tooling (C) .
After cleaning the threads, remove any debris from the head bolt holes on the cylinder block with a vacuum hose.
Visually inspect the head bolt holes on the cylinder block for thread damage.
If a damaged head bolt thread is observed, repair the damaged head bolt thread with a Heli-Coil thread repair kit.
Inspect the cylinder head and the cylinder block for flatness. Refer to Guideline for Reusable Parts and Salvage Operations, SEBF8162, "Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Install the correct cylinder head gasket on the cylinder block.Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to install the cylinder head.
Attach Tooling (A) and a suitable lifting device to the cylinder head. The weight of the cylinder head is approximately 184 kg (405 lb).
Illustration 1 g01801014
Install cylinder head (22) .
Install new cylinder head bolts (20) . If the engine is equipped with a compression brake, then also install new head bolt studs.
Lubricate the bolt threads, the underside of the bolt heads, and the washers with Tooling (B) prior to assembly. Follow Step 12 for the correct tightening procedure.
Illustration 2 g00950659
Tighten the cylinder head bolts according to the following procedure:
Tighten bolt (1) through bolt (26) in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Tighten bolt (1) through bolt (26) again in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Place a mark on bolt (1) through bolt (26) . Rotate bolt (1) through bolt (26) in a numerical sequence for an additional 120 5 degrees (1/3 turn).
Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.
Tighten bolt (1) through bolt (26) in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Tighten bolt (1) through bolt (26) again in a numerical sequence to a torque of 170 10 N m (125 7 lb ft).
Place a mark on bolt (1) through bolt (26) . Rotate bolt (1) through bolt (26) in a numerical sequence for an additional 120 5 degrees (1/3 turn).
Tighten bolt (27) through bolt (34) in a numerical sequence to a torque of 55 10 N m (41 7 lb ft).
Illustration 3 g01018718
View A-ANote: Lubricate the bores for the cup plugs with Tooling (D) prior to installing the cup plugs. The cup plugs are measured from the head face to the top edge of the plug.
Install the cup plugs to a depth (23) of 1.25 0.25 mm (0.049 0.010 inch).Note: The minimum permissible thickness of cylinder head should be the following value 104.35 mm (4.108 inch). The flatness of the cylinder head should be within 0.15 mm

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
797F Off-Highway Truck LTZ00001-UP (MACHINE) POWERED BY C175 Engine
785G Off-Highway Truck RTL00001-UP (MACHINE) POWERED BY 3512E Engine
793F OFF-HIGHWAY TRUCK D3T00001-UP (MACHINE) POWERED BY C175 ENGINE
797F Off-Highway Truck LAJ00001-UP (MACHINE) POWERED BY C175-20 Engine
793F Off-Highway Truck SSP00001-UP (MACHINE) POWERED BY C175-16 Engine
795F-AC Off-Highway Truck ERM00001-UP (MACHINE) POWERED BY C175-16 Engine
793F XQ Off-Highway Truck SND00001-UP (MACHINE) POWERED BY C175-16 Engine
793F CMD Off-Highway Truck (Command for Hauling) RBT00001-UP (MACHINE) POWERED BY C175-16 Engine
793F OEM Off-Highway Truck SXP00003-UP (MACHINE) POWERED BY C175-16 Engine
795F XQ Off-Highway Truck SNT00001-UP (MACHINE) POWERED BY C175-16 Engine


Parts harness Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.