AVSPARE.COM
parts catalog

HARNESS AS 8X9205 - Caterpillar


8X9205 HARNESS AS Caterpillar parts 621F, 623E, 623F, 627F
Rating:
42
Alternative (cross code) number:
CA8X9205
8X-9205
8X9205
Caterpillar 8X9205 HARNESS AS
Weight: 3 pounds 1 kg.

Buy HARNESS AS 8X9205 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SCRAPER, WHEEL TRACTOR,

Compatible equipment models: 8X9205:

WHEEL SCRAPER  623E   623F  
WHEEL TRACTOR  621F   627F   Caterpillar
Number on catalog scheme: 12
  For full view, you need register

Information:


In the stalled position, damage to the auger or damage to the auger hydraulic system can occur if the auger is operated for more than 10 seconds. Do not operate the auger continuously for more than 10 seconds when the auger is locked in the stalled position.
Refer to Testing and Adjusting, "Machine Preparation for Troubleshooting".Some of the adjustments on the piston pump and the piston motor require the auger to be stalled. The following procedure provides a safe method for stalling the auger.Procure the following materials:
Procure one square tubing that is at least 10.2 cm (4.00 inch) wide, 10.2 cm (4.00 inch) tall and 9.4 mm (.37 inch).
Procure one plate that is 12.7 cm (5.00 inch) wide, 12.7 cm (5.00 inch) tall and 1.3 cm (.50 inch) thick.
Make sure that the scraper bowl has a slight downward pressure on the ground. Raise the apron.
Illustration 1 g00566893
Typical Example (1) Apron locking pin
Install apron locking pin (1). Installation of apron locking pin (1) ensures that the apron stays in the UP position. This keeps the work area safe while the work is being performed in the scraper bowl.
Move the ejector control to the rear. Remove any loose dirt and loose debris from the left side of the floor of the scraper bowl. Remove any loose dirt and loose debris from the left side of the scraper bowl.
Illustration 2 g00566894
Typical Example (2) Location of weld (3) Location of weld (4) Leading edge of the auger (5) Square tubing (6) Left wall of the scraper bowl
Align leading edge (4) of the auger parallel with the left side of scraper bowl (6) .
Cut square tubing (5) to an approximate length. The tubing must fit between the leading edge of the auger (4) and left side of the scraper bowl (6) .
Weld the plate to one end of square tubing (5) .
Lay square tubing (5) in the scraper bowl between leading edge (4) and left wall (6). Place the end of square tubing (5) with the plate end against leading edge (4) .
Lay down a 8 cm (3 inch) weld at location (2). Lay down the same weld on the other side of square tubing (5). Lay down a 8 cm (3 inch) weld at location (3). Lay down the same weld on the other side of square tubing (5) .
Close the apron.
After you complete the adjustment procedures, cut square tubing (5) from the scraper bowl. Grind the welds smooth.

Caterpillar parts catalog:

Caterpillar parts catalog
621F Wheel Tractor Scraper 4SK00001-UP (MACHINE) POWERED BY 3406 Engine
621F Wheel Tractor-Scraper 8PL00001-UP (MACHINE) POWERED BY 3406C Engine
627F Wheel Tractor Scraper 1DL00001-UP (MACHINE)
623F Wheel Tractor-Scraper 5SG00480-UP (MACHINE) POWERED BY 3406C Engine
623F Wheel Tractor-Scraper 3XW00001-UP (MACHINE) POWERED BY 3406C Engine


Parts harness Caterpillar catalog:

8X7550 HARNESS AS
621F, 623E, 623F, 627F
8X7794 HARNESS AS
621F, 623E, 623F, 627F
8X7550 HARNESS AS
621F, 623E, 623F, 627F
8X9692 HARNESS AS
621F, 623E, 623F, 627F
1605742 HARNESS AS-CHASSIS
621F, 623E, 623F, 627F
1572441 HARNESS AS-CHASSIS
621F, 623E, 623F, 627F
1446277 HARNESS AS-ENGINE
621F, 623E, 623F, 627F
8X7794 HARNESS AS
621F, 623E, 623F, 627F
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.