1627487 HEAD Caterpillar parts
824G II, 824H, D10R, D10T
Rating:
Alternative (cross code) number:
CA1627487
162-7487
1627487
CA1627487
162-7487
1627487
Weight: 41 pounds 18 kg.
Information:
FLANGE SIZE
270.6
INSERT DIAMETER
158.67
INSERT LENGTH
32
INSIDE DIAMETER
89.18
PORT LOCATION
130.18
QUANTITY OF HOLES
6
PORT SIZE
32.00
TRACK-TYPE TRACTOR, WHEEL DOZER,
This part in 2 request:
Show.
This information for suppliers only!
2019-08-02
2018-04-05
Compatible equipment models: 1627487:
Information:
The spring of the recoil spring assembly is compressed under several tons of force.Do not attempt to compress or release the tension of the spring with the nut on the end of the retaining rod.Damaged threads on the retaining rod or nut can cause the assembly to come apart with force, resulting in injury or death.
Note: Prior to assembling the recoil spring assembly, make sure that Tooling (A) is on a level surface.
Illustration 1 g00859172
Check the condition of the threads on recoil spring retaining rod (13) and nut (6) . If the threads are worn or damaged, use new parts for replacement.
Check the inside of support assembly (11) . Make sure that the support assembly is clean and free of dirt.
Assemble the recoil spring assembly loosely. Install spring (10) in support assembly (11) . Install recoil spring retaining rod (13) and support (9) .
Illustration 2 g00859362
Note: The use of a pry bar might be necessary to line up support (9) with support assembly (11) . Place the pry bar between the recoil spring assembly and movable plate (3) of Tooling (A) to line up the support with the support assembly.
Illustration 3 g00858995
The weight of the recoil spring assembly is approximately 590 kg (1300 lb). Use a suitable lifting device in order to position the recoil spring assembly on adjustable supports (1) in Tooling (A) . Adjust the adjustable supports in order to align the centerline of the recoil spring assembly with the centerline of Tooling (A) .
Illustration 4 g00859150
Illustration 5 g00859153
Note: The suitable lifting device has been removed from the recoil spring assembly in order to provide a better illustration of level gauge (4) .
Put a level gauge (4) on the recoil spring assembly. Reposition the recoil spring assembly until the recoil spring assembly is level. Reposition the recoil spring assembly until the retaining rod and nut (6) are centered in the hole in reaction plate (2) . The recoil spring assembly is leveled by moving adjustable supports (1) higher or lower. After the recoil spring assembly is leveled and centered, install two pins (5) on the back side of reaction plate (2) , as shown.
Illustration 6 g00858923
Install Tooling (C) on Tooling (B) .
Operate Tooling (B) in order to hold the recoil spring assembly in position between reaction plate (2) and movable plate (3) . Make sure that the recoil spring assembly is level and centered in Tooling (A) .
Illustration 7 g00859769
Illustration 8 g00859159
Close covers (7) on Tooling (A) . Compress the recoil spring assembly with Tooling (B) . Open the covers on Tooling (A) , and measure the assembled length of the recoil spring assembly. Measure the distance from the end of the support assembly to the mark on support (9) , as shown. Dimension (X) is the assembled length of the recoil spring assembly. The assembled length must be 1194.0 1.0 mm (47.0 0.04 inch). If the assembled length is not correct, close covers (7) on Tooling (A) , and use Tooling (B) to adjust the spring length. If the assembled length
Caterpillar parts catalog:
Parts head Caterpillar catalog:
1926447
HEAD
854G, D10R, D10T
854G, D10R, D10T
1009965
HEAD
854G, D10N, D10R, D10T, D9N
854G, D10N, D10R, D10T, D9N
1422723
HEAD
D10N, D10R
D10N, D10R
6E3667
HEAD
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
6E6199
HEAD
D10N, D10R
D10N, D10R
9T4447
HEAD AS
D10N, D10R, D10T, D9L
D10N, D10R, D10T, D9L
1170111
HEAD
824G, 824G II, 824H
824G, 824G II, 824H
2110885
HEAD
824G II, 824H
824G II, 824H
3989666
HEAD
D10T
D10T
2476304
HEAD AS
D10N, D10R, D10T
D10N, D10R, D10T
2476306
HEAD
D10N, D10R, D10T
D10N, D10R, D10T
2476402
HEAD-MOTOR
D10N, D10R, D10T, D11R, D11T
D10N, D10R, D10T, D11R, D11T
1636474
HEAD
D8R, D8R II, D8T
D8R, D8R II, D8T
1913583
HEAD
D8N, D8R, D8R II, D8T
D8N, D8R, D8R II, D8T
1096779
HEAD
844, 844H, 844K, D9R, D9T
844, 844H, 844K, D9R, D9T
1238096
HEAD
D9R
D9R
1238095
HEAD
D9R
D9R
1646403
HEAD
D8L, D9N, D9R, D9T
D8L, D9N, D9R, D9T
1009965
HEAD
854G, D10N, D10R, D10T, D9N
854G, D10N, D10R, D10T, D9N
1926447
HEAD
854G, D10R, D10T
854G, D10R, D10T
2481381
HEAD
834H
834H
1627757
HEAD
844, 844H, 854G, 854K, D11N, D11R, D11T
844, 844H, 854G, 854K, D11N, D11R, D11T
6E5702
HEAD
D11N, D11R, D11T
D11N, D11R, D11T
3342648
HEAD
D11N, D11R, D11T
D11N, D11R, D11T