1646403 HEAD Caterpillar parts
D8L, D9N, D9R, D9T
Rating:
Alternative (cross code) number:
CA1646403
164-6403
1646403
CA1646403
164-6403
1646403
Weight: 9 pounds 4 kg.
Information:
FLANGE DIAMETER
152
mm
INSERT DIAMETER
125.25
INSERT LENGTH
79
INSIDE DIAMETER
76.53
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Scepter 6 Gallon Under Seat Portable Marine Tank with 2-Way Vented Cap, EPA CARB Fuel Can Container for Boats and Watercraft, 19.3"L x 12.2"W x 10.2"H
Scepter Portable Size Tank: 6 Gallon capacity measures 19.3"L x 12.2"W x 10.2"H and is great for marine vehicles || Vented Cap: Unique 2-way vented cap allows air to enter the tank during operation and pressure to be released above 5 PSI || Under-the-Seat Design: Compact design for convenient under-seat storage in your boat or watercraft and easy transport || Convenient Gauge: Combination fuel pick-up/sight gauge accepts standard 1/4 NPT marine tank fittings || Reliable Construction: Made of HDPE which is Ultra violet stabilized and resists rust and corrosion for maximum durability
Scepter Portable Size Tank: 6 Gallon capacity measures 19.3"L x 12.2"W x 10.2"H and is great for marine vehicles || Vented Cap: Unique 2-way vented cap allows air to enter the tank during operation and pressure to be released above 5 PSI || Under-the-Seat Design: Compact design for convenient under-seat storage in your boat or watercraft and easy transport || Convenient Gauge: Combination fuel pick-up/sight gauge accepts standard 1/4 NPT marine tank fittings || Reliable Construction: Made of HDPE which is Ultra violet stabilized and resists rust and corrosion for maximum durability
Scepter 6 Gallon Under Seat Portable Marine Tank with 2-Way Vented Cap, EPA CARB Fuel Can Container for Boats and Watercraft, 19.3"L x 12.2"W x 10.2"H
Scepter Portable Size Tank: 6 Gallon capacity measures 19.3"L x 12.2"W x 10.2"H and is great for marine vehicles || Vented Cap: Unique 2-way vented cap allows air to enter the tank during operation and pressure to be released above 5 PSI || Under-the-Seat Design: Compact design for convenient under-seat storage in your boat or watercraft and easy transport || Convenient Gauge: Combination fuel pick-up/sight gauge accepts standard 1/4 NPT marine tank fittings || Reliable Construction: Made of HDPE which is Ultra violet stabilized and resists rust and corrosion for maximum durability
Scepter Portable Size Tank: 6 Gallon capacity measures 19.3"L x 12.2"W x 10.2"H and is great for marine vehicles || Vented Cap: Unique 2-way vented cap allows air to enter the tank during operation and pressure to be released above 5 PSI || Under-the-Seat Design: Compact design for convenient under-seat storage in your boat or watercraft and easy transport || Convenient Gauge: Combination fuel pick-up/sight gauge accepts standard 1/4 NPT marine tank fittings || Reliable Construction: Made of HDPE which is Ultra violet stabilized and resists rust and corrosion for maximum durability
Scepter 6 Gallon Under Seat Portable Marine Tank with 2-Way Vented Cap, EPA CARB Fuel Can Container for Boats and Watercraft, 19.3"L x 12.2"W x 10.2"H
Scepter Portable Size Tank: 6 Gallon capacity measures 19.3"L x 12.2"W x 10.2"H and is great for marine vehicles || Vented Cap: Unique 2-way vented cap allows air to enter the tank during operation and pressure to be released above 5 PSI || Under-the-Seat Design: Compact design for convenient under-seat storage in your boat or watercraft and easy transport || Convenient Gauge: Combination fuel pick-up/sight gauge accepts standard 1/4 NPT marine tank fittings || Reliable Construction: Made of HDPE which is Ultra violet stabilized and resists rust and corrosion for maximum durability
Scepter Portable Size Tank: 6 Gallon capacity measures 19.3"L x 12.2"W x 10.2"H and is great for marine vehicles || Vented Cap: Unique 2-way vented cap allows air to enter the tank during operation and pressure to be released above 5 PSI || Under-the-Seat Design: Compact design for convenient under-seat storage in your boat or watercraft and easy transport || Convenient Gauge: Combination fuel pick-up/sight gauge accepts standard 1/4 NPT marine tank fittings || Reliable Construction: Made of HDPE which is Ultra violet stabilized and resists rust and corrosion for maximum durability
Number on catalog scheme:
6
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
Remove the crankshaft front seal . Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces. Wear sleeves are not original equipment. A new crankshaft front seal must be installed when a new wear sleeve is installed.
Illustration 1 g01269535
Sectional view of the crankshaft pulley and the wear sleeve
Use a sharp tool to score a deep line across wear sleeve (1). Note: Take care to avoid damaging to the crankshaft pulley.
Insert a thin blade between wear sleeve (1) and crankshaft pulley (2) below the scored line. The wear sleeve will separate along the line.
Remove wear sleeve (1) from crankshaft pulley (2). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description
A 1U-8846 Gasket Maker
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft pulley is thoroughly clean and dry. Remove any areas of raised damage.
Illustration 2 g01269521
Sectional view of the wear sleeve
Apply a small continuous bead of Tooling (A) to the inner surface of wear sleeve (1) at Position X. Apply the bead of Tooling (A) 5.00 mm (0.2 inch) from the flange end of the wear sleeve.
Illustration 3 g01258423
Typical example
Illustration 4 g01258430
Sectional view of the crankshaft pulley, the wear sleeve and the installation tool
Align wear sleeve (1) with crankshaft pulley (2). Use installation tool (3) that is provided with the wear sleeve and use a suitable press in order to install wear sleeve (1) onto crankshaft pulley (2). Note: Ensure that the wear sleeve is installed squarely against the shoulder of the crankshaft pulley.
Remove installation tool (3) from wear sleeve (1).
Ensure that wear sleeve (1) has no rough edges. End By:
Install a new crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove and Install".
Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
Start By:
Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
Remove the crankshaft front seal . Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces. Wear sleeves are not original equipment. A new crankshaft front seal must be installed when a new wear sleeve is installed.
Illustration 1 g01269535
Sectional view of the crankshaft pulley and the wear sleeve
Use a sharp tool to score a deep line across wear sleeve (1). Note: Take care to avoid damaging to the crankshaft pulley.
Insert a thin blade between wear sleeve (1) and crankshaft pulley (2) below the scored line. The wear sleeve will separate along the line.
Remove wear sleeve (1) from crankshaft pulley (2). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description
A 1U-8846 Gasket Maker
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft pulley is thoroughly clean and dry. Remove any areas of raised damage.
Illustration 2 g01269521
Sectional view of the wear sleeve
Apply a small continuous bead of Tooling (A) to the inner surface of wear sleeve (1) at Position X. Apply the bead of Tooling (A) 5.00 mm (0.2 inch) from the flange end of the wear sleeve.
Illustration 3 g01258423
Typical example
Illustration 4 g01258430
Sectional view of the crankshaft pulley, the wear sleeve and the installation tool
Align wear sleeve (1) with crankshaft pulley (2). Use installation tool (3) that is provided with the wear sleeve and use a suitable press in order to install wear sleeve (1) onto crankshaft pulley (2). Note: Ensure that the wear sleeve is installed squarely against the shoulder of the crankshaft pulley.
Remove installation tool (3) from wear sleeve (1).
Ensure that wear sleeve (1) has no rough edges. End By:
Install a new crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove and Install".
Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
Caterpillar parts catalog:
Parts head Caterpillar catalog:
D5H XL, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6R, D6R II, D7G2, D7H, D7R, D7R II, D7R XR, D8N, D9N
D9R, D9T
980C, 980F, 980F II, D8L, D8N, R1600, R1600G, R1600H
854G, D10N, D10R, D10T, D9N
6E3972
HEAD
D9R
D9R
844, 844H, 844K, D9N
9T5283
HEAD
844, 844H, D8L, D9N
844, 844H, D8L, D9N
2447202
HEAD
D9T
D9T
3G8186
HEAD
D8L
D8L
9T3505
HEAD
D10, D10N, D11N, D8L, D9L
D10, D10N, D11N, D8L, D9L
9T2828
HEAD
D8L, D9N
D8L, D9N
1980653
HEAD
320C
320C
5P0446
HEAD
320B
320B
1373665
HEAD
322B
322B
1261875
HEAD
322B
322B
5I4614
HEAD
320B L
320B L
1627487
HEAD
824G II, 824H, D10R, D10T
824G II, 824H, D10R, D10T
D8R, D8R II, D8T
D8N, D8R, D8R II, D8T
844, 844H, 844K, D9R, D9T
1238096
HEAD
D9R
D9R
1238095
HEAD
D9R
D9R