1913583 HEAD Caterpillar parts
D8N, D8R, D8R II, D8T
Rating:
Alternative (cross code) number:
CA1913583
191-3583
1913583
CA1913583
191-3583
1913583
Weight: 48 pounds 21 kg.
Information:
BORE SIZE
184.15
mm
HEAD TYPE
MTG BOLT
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Information:
This diagnostic code is recorded when the implement ECM receives information from the monitoring system ECM and the information is NOT correct.The possible causes of this diagnostic code are listed:
A problem with the data link harness
The monitoring system is not operational
The monitoring system has not been programmed with the correct application softwareNote: Other related diagnostic codes may cause this diagnostic code. Check for other related diagnostic codes.System Response:If the ECM has never been flashed, all implement functions will be disabled. There is a 10 second delay before implement functions are active.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS.
Verify whether the following part numbers are correct:
Software part number for the implement ECM
Software part number for the caterpillar monitoring systemNote: Consult the Business Unit that is producing the product for the correct configuration of the machine. Expected Result:All part numbers are correct.Results:
OK - All part numbers are correct. Proceed to Test Step 2.
NOT OK - All of the part number are NOT correct.Repair: One of the following modules may have the wrong part number and/or the software configuration is NOT correct: the implement ECM, the caterpillar monitoring system and the power train ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program". Stop.Test Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the key start switch and the disconnect switch to the OFF position.
Inspect the harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the mating of the connector.
Check the wires at the connector.
Check each wire for nicks and/or signs of abrasion in the insulation.
Check for moisture at the connector.
Check for dirty contacts and/or corroded contacts.
Check each pin and check each socket.Expected Result:The machine harness connectors are tight and free of corrosion.Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to Test Step 3.
NOT - The machine harness connectors require repair.Repair: Repair the harness or replace the harness. Stop.Test Step 3. CHECK FOR ADDITIONAL RELATED DIAGNOSTIC CODES.
Ensure that all electronic control modules that use the Cat Data Link are connected.
Turn the disconnect switch and the key start switch to the ON position.
Acknowledge and troubleshoot any active diagnostic codes that are currently displayed on the message center.
Verify that NO related diagnostic codes are present. Expected Result:No other diagnostic codes are present.Results:
OK - No other diagnostic codes are present. Proceed to Test Step 4.
NOT OK - Other related diagnostic codes are present.Repair: Exit this procedure and perform the other related diagnostic codes. Verify that the other related diagnostic codes are NOT present. Observe the status of CID 0967 FMI 09. If CID 0967 FMI 09 remains active, perform CID 0967 FMI 09 again. Stop.Test Step 4. CHECK FOR SHORTS TO GROUND.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness from all electronic control modules that use the Cat Data Link.
At the machine harness for the implement ECM, measure the resistance between frame ground and the following data link circuits:
Contact
A problem with the data link harness
The monitoring system is not operational
The monitoring system has not been programmed with the correct application softwareNote: Other related diagnostic codes may cause this diagnostic code. Check for other related diagnostic codes.System Response:If the ECM has never been flashed, all implement functions will be disabled. There is a 10 second delay before implement functions are active.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS.
Verify whether the following part numbers are correct:
Software part number for the implement ECM
Software part number for the caterpillar monitoring systemNote: Consult the Business Unit that is producing the product for the correct configuration of the machine. Expected Result:All part numbers are correct.Results:
OK - All part numbers are correct. Proceed to Test Step 2.
NOT OK - All of the part number are NOT correct.Repair: One of the following modules may have the wrong part number and/or the software configuration is NOT correct: the implement ECM, the caterpillar monitoring system and the power train ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program". Stop.Test Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the key start switch and the disconnect switch to the OFF position.
Inspect the harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the mating of the connector.
Check the wires at the connector.
Check each wire for nicks and/or signs of abrasion in the insulation.
Check for moisture at the connector.
Check for dirty contacts and/or corroded contacts.
Check each pin and check each socket.Expected Result:The machine harness connectors are tight and free of corrosion.Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to Test Step 3.
NOT - The machine harness connectors require repair.Repair: Repair the harness or replace the harness. Stop.Test Step 3. CHECK FOR ADDITIONAL RELATED DIAGNOSTIC CODES.
Ensure that all electronic control modules that use the Cat Data Link are connected.
Turn the disconnect switch and the key start switch to the ON position.
Acknowledge and troubleshoot any active diagnostic codes that are currently displayed on the message center.
Verify that NO related diagnostic codes are present. Expected Result:No other diagnostic codes are present.Results:
OK - No other diagnostic codes are present. Proceed to Test Step 4.
NOT OK - Other related diagnostic codes are present.Repair: Exit this procedure and perform the other related diagnostic codes. Verify that the other related diagnostic codes are NOT present. Observe the status of CID 0967 FMI 09. If CID 0967 FMI 09 remains active, perform CID 0967 FMI 09 again. Stop.Test Step 4. CHECK FOR SHORTS TO GROUND.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness from all electronic control modules that use the Cat Data Link.
At the machine harness for the implement ECM, measure the resistance between frame ground and the following data link circuits:
Contact
Cat SIS web machinery list:
Parts head Caterpillar catalog:
6E1113
HEAD
D8N
D8N
1010051
HEAD
D8N, D8R
D8N, D8R
6E0402
HEAD
D8N, D8R, D8R II, D8T
D8N, D8R, D8R II, D8T
6E4247
HEAD-LH
D8N, D8R, D8R II
D8N, D8R, D8R II
6E4380
HEAD
D8N, D8R
D8N, D8R
1206674
HEAD
CB-614, D8N, D8R
CB-614, D8N, D8R
1784147
HEAD
5110B, 795F AC, 795F XQ, D8R, D8R II
5110B, 795F AC, 795F XQ, D8R, D8R II
1636474
HEAD
D8R, D8R II, D8T
D8R, D8R II, D8T
1838415
HEAD
D8R, D8R II
D8R, D8R II
1553849
HEAD
D8R, D8R II, D8T
D8R, D8R II, D8T
1553856
HEAD
D8R, D8R II, D8T
D8R, D8R II, D8T
1096779
HEAD
844, 844H, 844K, D9R, D9T
844, 844H, 844K, D9R, D9T
1238096
HEAD
D9R
D9R
1238095
HEAD
D9R
D9R
1646403
HEAD
D8L, D9N, D9R, D9T
D8L, D9N, D9R, D9T
1980653
HEAD
320C
320C
2481381
HEAD
834H
834H
1627757
HEAD
844, 844H, 854G, 854K, D11N, D11R, D11T
844, 844H, 854G, 854K, D11N, D11R, D11T
6E5702
HEAD
D11N, D11R, D11T
D11N, D11R, D11T
3342648
HEAD
D11N, D11R, D11T
D11N, D11R, D11T
1627487
HEAD
824G II, 824H, D10R, D10T
824G II, 824H, D10R, D10T
1636474
HEAD
D8R, D8R II, D8T
D8R, D8R II, D8T