1916558 HEAD Caterpillar parts
416D, 420D, 428D, 432D, 438D, 442D
Rating:
Alternative (cross code) number:
CA1916558
191-6558
1916558
CA1916558
191-6558
1916558
Weight: 12 pounds 5 kg.
Information:
FLANGE DIAMETER
152
mm
INSERT DIAMETER
125.25
INSERT LENGTH
79
INSIDE DIAMETER
60.61
BACKHOE LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1916558 Hydraulic Cylinder Head for Model 416D/420D/428D/432D/438D/442D
CTP For Model 416D/420D/428D/432D/438D/442D || Sold in each || Easy in-and-out fit
CTP For Model 416D/420D/428D/432D/438D/442D || Sold in each || Easy in-and-out fit
CTP 1916558 Hydraulic Cylinder Head for Model 416D/420D/428D/432D/438D/442D
CTP For Model 416D/420D/428D/432D/438D/442D || Sold in each || Easy in-and-out fit
CTP For Model 416D/420D/428D/432D/438D/442D || Sold in each || Easy in-and-out fit
Information:
3100 Family Of EnginesIntroduction
The 115-4109 (Dry) and 115-4120 (Wet) Crankshaft Seals are a new design (combination seal/sleeve) that service the 7C-3570 (dry), 7E-7589 Crankshaft Seal (wet) and 7C-7980 Wear Sleeve. The design of the 115-4109 (Dry) and 115-4120 (Wet) Crankshaft Seals require special handling, tooling and installation procedures.Handling
Do NOT install the seal group if:* The seal has SEPARATED from the sleeve.* The seal group is NOT assembled when removed from the parts package.* The seal group appears to be DAMAGED in any way.* The seal group has been LUBRICATED. The seal group is designed to be installed DRY.* The seal group has been INSTALLED before. Do Not install a seal group that has been used. Install ONLY new seal groups.Tooling
The original seals are removed using the 1U-7600 Slide Puller Group and the new seal groups are installed with the 1U-7598 Seal Installation Group. The seal removal/installation may not require all the tools in the tool group.Required Tools
Remove Crankshaft Rear Seal
Refer to the Service Manual for the procedures to remove the flywheel. 1. Use a 1U-8145 Drill Bit and carefully drill three evenly spaced holes in seal (1). Drill the seal CAREFULLY to prevent damage to the rear flange surface of the crankshaft. The holes are to position the tools for the seal removal.2. Install one 1P-3073 Screw Tip (2) on assembled Slide Hammer (3). Remove seal CAREFULLY by alternating the position of the 1U-7603 Hammer from hole to hole to hole. This will allow the seal to be removed evenly without damage to the rear flange surface of the crankshaft.Crankshaft Salvage Wear Sleeve (If Equipped)
A factory built engine does not have a wear sleeve.Engine Equipped With Wear Sleeve
If the engine is equipped with a wear sleeve it could be either a:* 7C-7980, which is used in conjunction with a 7C-3570 (Dry) Crankshaft Seal .. or a* 7C-7589 (Wet) Crankshaft Seal .. or a* Wear sleeve that is part of a 115-4109 (Dry) Crankshaft or 115-4120 (Wet) Crankshaft Seal Group.Seal/Wear Sleeve Identification
The wear sleeve can be identified by identifying the seal used.The wear sleeve MUST be identified in order to use the correct tooling for the sleeve removal.7C-3570 Crankshaft Seal Or 7C-7989 Crankshaft Seal
A 7C-3570 Crankshaft Seal Or 7C-7589 Crankshaft Seal is removed using a 4C-4869 Distorter Ring.115-4109 Crankshaft Seal Or 115-4120 Crankshaft Seal
A 115-4109 Crankshaft Seal Or 115-4120 Crankshaft Seal is removed using a 5P-7314 Distorter Ring.
If the INCORRECT Distorter Ring is used:* The wear sleeve removal may be hampered or crankshaft damage could occur.
Remove Crankshaft Wear Sleeve
1. Install 4C-4869 Distorter Ring or 5P-7314 Distorter Ring (1), depending on crankshaft seal removed, in the rear seal bore.2. Install 5P-7409 Distorter (2) between 4C-4869 Distorter Ring or 5P-7314 Distorter Ring (1)Turn 5P-7409 Distorter (2) until the edge of the tool makes a crease in the wear sleeve.Repeat the turning procedure in two or three more locations on the wear sleeve or until the sleeve is loose.3. Remove 5P-7409 Distorter (2), 4C-4869 Distorter Ring or 5P-7314 Distorter Ring (1)
The 115-4109 (Dry) and 115-4120 (Wet) Crankshaft Seals are a new design (combination seal/sleeve) that service the 7C-3570 (dry), 7E-7589 Crankshaft Seal (wet) and 7C-7980 Wear Sleeve. The design of the 115-4109 (Dry) and 115-4120 (Wet) Crankshaft Seals require special handling, tooling and installation procedures.Handling
Do NOT install the seal group if:* The seal has SEPARATED from the sleeve.* The seal group is NOT assembled when removed from the parts package.* The seal group appears to be DAMAGED in any way.* The seal group has been LUBRICATED. The seal group is designed to be installed DRY.* The seal group has been INSTALLED before. Do Not install a seal group that has been used. Install ONLY new seal groups.Tooling
The original seals are removed using the 1U-7600 Slide Puller Group and the new seal groups are installed with the 1U-7598 Seal Installation Group. The seal removal/installation may not require all the tools in the tool group.Required Tools
Remove Crankshaft Rear Seal
Refer to the Service Manual for the procedures to remove the flywheel. 1. Use a 1U-8145 Drill Bit and carefully drill three evenly spaced holes in seal (1). Drill the seal CAREFULLY to prevent damage to the rear flange surface of the crankshaft. The holes are to position the tools for the seal removal.2. Install one 1P-3073 Screw Tip (2) on assembled Slide Hammer (3). Remove seal CAREFULLY by alternating the position of the 1U-7603 Hammer from hole to hole to hole. This will allow the seal to be removed evenly without damage to the rear flange surface of the crankshaft.Crankshaft Salvage Wear Sleeve (If Equipped)
A factory built engine does not have a wear sleeve.Engine Equipped With Wear Sleeve
If the engine is equipped with a wear sleeve it could be either a:* 7C-7980, which is used in conjunction with a 7C-3570 (Dry) Crankshaft Seal .. or a* 7C-7589 (Wet) Crankshaft Seal .. or a* Wear sleeve that is part of a 115-4109 (Dry) Crankshaft or 115-4120 (Wet) Crankshaft Seal Group.Seal/Wear Sleeve Identification
The wear sleeve can be identified by identifying the seal used.The wear sleeve MUST be identified in order to use the correct tooling for the sleeve removal.7C-3570 Crankshaft Seal Or 7C-7989 Crankshaft Seal
A 7C-3570 Crankshaft Seal Or 7C-7589 Crankshaft Seal is removed using a 4C-4869 Distorter Ring.115-4109 Crankshaft Seal Or 115-4120 Crankshaft Seal
A 115-4109 Crankshaft Seal Or 115-4120 Crankshaft Seal is removed using a 5P-7314 Distorter Ring.
If the INCORRECT Distorter Ring is used:* The wear sleeve removal may be hampered or crankshaft damage could occur.
Remove Crankshaft Wear Sleeve
1. Install 4C-4869 Distorter Ring or 5P-7314 Distorter Ring (1), depending on crankshaft seal removed, in the rear seal bore.2. Install 5P-7409 Distorter (2) between 4C-4869 Distorter Ring or 5P-7314 Distorter Ring (1)Turn 5P-7409 Distorter (2) until the edge of the tool makes a crease in the wear sleeve.Repeat the turning procedure in two or three more locations on the wear sleeve or until the sleeve is loose.3. Remove 5P-7409 Distorter (2), 4C-4869 Distorter Ring or 5P-7314 Distorter Ring (1)
Caterpillar parts catalog:
Parts head Caterpillar catalog:
1482593
HEAD
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, ...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, ...
1548050
HEAD
416C, 420D, 428C, 428D, 432D, 438C, 438D, 442D
416C, 420D, 428C, 428D, 432D, 438C, 438D, 442D
1843711
HEAD
416C, 416D, 420D, 424D, 428C, 428D, 432D, 438C, 438D, 442D
416C, 416D, 420D, 424D, 428C, 428D, 432D, 438C, 438D, 442D
2359832
HEAD
416C, 416D, 420D, 424D, 428D, 432D, 438D, 442D, 928HZ, 930G
416C, 416D, 420D, 424D, 428D, 432D, 438D, 442D, 928HZ, 930G
1873510
HEAD
24M, 416D, 416E, 416F, 420E, 420F, 424D, 428D, 432D, 438D, 442D
24M, 416D, 416E, 416F, 420E, 420F, 424D, 428D, 432D, 438D, 442D
1916112
HEAD
414E, 416D, 416E, 422E, 424D
414E, 416D, 416E, 422E, 424D
1895629
HEAD
416D, 420D, 430D
416D, 420D, 430D
2014826
HEAD
416D, 420D, 420E, 430D, 430E, 525B, 525C, 525D, 535B, 535C, 535D, 545, 545C, 545D, 555D
416D, 420D, 420E, 430D, 430E, 525B, 525C, 525D, 535B, 535C, 535D, 545, 545C, 545D, 555D
1916191
HEAD
416D, 420D, 430D, 430E, 430F, 432D, 438D, 442D, 442E, 444E, 446D
416D, 420D, 430D, 430E, 430F, 432D, 438D, 442D, 442E, 444E, 446D
1916149
HEAD
420D, 420E, 428D, 428E, 430D, 430E, 432D, 432E, 438D, 442D, 442E
420D, 420E, 428D, 428E, 430D, 430E, 432D, 432E, 438D, 442D, 442E
1916577
HEAD-CYLINDER
416D, 420D, 424D, 428D, 432D, 438D, 442D
416D, 420D, 424D, 428D, 432D, 438D, 442D
2332595
HEAD AS
416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 446D, 450E, 527
416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 446D, 450E, 527
1916314
HEAD
416D, 424D
416D, 424D
1873510
HEAD
24M, 416D, 416E, 416F, 420E, 420F, 424D, 428D, 432D, 438D, 442D
24M, 416D, 416E, 416F, 420E, 420F, 424D, 428D, 432D, 438D, 442D
1835724
HEAD
TH103
TH103
1835723
HEAD
TH82, TH83
TH82, TH83
1729981
HEAD
14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 446B, 446D, 928H, 988G, 988H, D6H XL, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR, IT28G
14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 446B, 446D, 928H, 988G, 988H, D6H XL, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR, IT28G
1235830
HEAD-PUMP
446B, 446D
446B, 446D
1923849
HEAD
420D, 420E, 428D, 428E, 430D, 430E, 432D, 432E, 438D, 442D, 442E
420D, 420E, 428D, 428E, 430D, 430E, 432D, 432E, 438D, 442D, 442E
1839170
HEAD
420D, 428D, 430D, 432D, 438D, 442D
420D, 428D, 430D, 432D, 438D, 442D
1916191
HEAD
416D, 420D, 430D, 430E, 430F, 432D, 438D, 442D, 442E, 444E, 446D
416D, 420D, 430D, 430E, 430F, 432D, 438D, 442D, 442E, 444E, 446D
2014826
HEAD
416D, 420D, 420E, 430D, 430E, 525B, 525C, 525D, 535B, 535C, 535D, 545, 545C, 545D, 555D
416D, 420D, 420E, 430D, 430E, 525B, 525C, 525D, 535B, 535C, 535D, 545, 545C, 545D, 555D
1895629
HEAD
416D, 420D, 430D
416D, 420D, 430D
1916112
HEAD
414E, 416D, 416E, 422E, 424D
414E, 416D, 416E, 422E, 424D