1926447 HEAD Caterpillar parts
854G, D10R, D10T
Rating:
Alternative (cross code) number:
CA1926447
192-6447
1926447
CA1926447
192-6447
1926447
Weight: 72 pounds 33 kg.
Information:
FLANGE SIZE
341.28
INSERT DIAMETER
234.87
INSERT LENGTH
26
INSIDE DIAMETER
89.18
PORT LOCATION
155.58
QUANTITY OF HOLES
6
PORT SIZE
25.50
TRACK-TYPE TRACTOR, WHEEL DOZER,
Related part:
1926447
HEAD-HYD CYL-YM
4259365
CL
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1
C - Loctite 5900 -
D 6V-6640 Sealant 1
E - Straight Edge 1 Note: In order to install a cast iron oil pan, the engine must be removed from the application.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the joint face of the cylinder block is clean and free from damage. Inspect the studs in the cylinder block for damage. If necessary, replace the studs.
Ensure that the engine oil pan is clean and free from damage.
Illustration 1 g01340933
Typical example
Apply a bead of Tooling (C) to positions (Y).
Illustration 2 g01340934
Align a new joint (4) with the studs and install the joint to the cylinder block.
Attach a suitable lifting device to the engine oil pan (7). The engine oil pan can weigh 100 kg (220 lb).
Use the lifting device to align the engine oil pan (7) with the studs . Install the engine oil pan to the cylinder block.
Install bolts (8) and (9), nuts (10) and the torx screws (11) finger tight.
Align the rear face of the engine oil pan to the rear face of the cylinder block. Use Tooling (E) and a feeler gauge in order to check the alignment between the engine oil pan and the cylinder block.
Illustration 3 g01399279
Typical example
Tighten bolts (8) and (9), and nuts (10) to a torque of 22 N m (16 lb ft). Use Tooling (A) in order to tighten torx screws (11) to a torque of 22 N m (16 lb ft). Tighten the fasteners in the sequence that is shown in Illustration 3.
Install a new O-ring seal (6) to drain plug (5). Install drain plug (5) to engine oil pan (7). Tighten the drain plug to a torque of 34 N m (25 lb ft).
Illustration 4 g01340605
If necessary, follow Steps 11 through 11.c in order to install the assembly of the dipstick tube.
Install a new seal (3) to tube assembly (2).
Apply Tooling (D) to nut (1). Install the tube assembly to the engine oil pan. Note: Ensure that the orientation of the tube assembly is correct.
Tighten the nut to a torque of 18 N m (13 lb ft). Install the dipstick. Note: After the engine has been installed, ensure that the engine oil pan is filled with lubricating oil to the correct level. Refer to Operation and Maintenance Manual, "Oil Filter Change" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1
C - Loctite 5900 -
D 6V-6640 Sealant 1
E - Straight Edge 1 Note: In order to install a cast iron oil pan, the engine must be removed from the application.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the joint face of the cylinder block is clean and free from damage. Inspect the studs in the cylinder block for damage. If necessary, replace the studs.
Ensure that the engine oil pan is clean and free from damage.
Illustration 1 g01340933
Typical example
Apply a bead of Tooling (C) to positions (Y).
Illustration 2 g01340934
Align a new joint (4) with the studs and install the joint to the cylinder block.
Attach a suitable lifting device to the engine oil pan (7). The engine oil pan can weigh 100 kg (220 lb).
Use the lifting device to align the engine oil pan (7) with the studs . Install the engine oil pan to the cylinder block.
Install bolts (8) and (9), nuts (10) and the torx screws (11) finger tight.
Align the rear face of the engine oil pan to the rear face of the cylinder block. Use Tooling (E) and a feeler gauge in order to check the alignment between the engine oil pan and the cylinder block.
Illustration 3 g01399279
Typical example
Tighten bolts (8) and (9), and nuts (10) to a torque of 22 N m (16 lb ft). Use Tooling (A) in order to tighten torx screws (11) to a torque of 22 N m (16 lb ft). Tighten the fasteners in the sequence that is shown in Illustration 3.
Install a new O-ring seal (6) to drain plug (5). Install drain plug (5) to engine oil pan (7). Tighten the drain plug to a torque of 34 N m (25 lb ft).
Illustration 4 g01340605
If necessary, follow Steps 11 through 11.c in order to install the assembly of the dipstick tube.
Install a new seal (3) to tube assembly (2).
Apply Tooling (D) to nut (1). Install the tube assembly to the engine oil pan. Note: Ensure that the orientation of the tube assembly is correct.
Tighten the nut to a torque of 18 N m (13 lb ft). Install the dipstick. Note: After the engine has been installed, ensure that the engine oil pan is filled with lubricating oil to the correct level. Refer to Operation and Maintenance Manual, "Oil Filter Change" for the correct procedure.
Caterpillar parts catalog:
Parts head Caterpillar catalog:
1627487
HEAD
824G II, 824H, D10R, D10T
824G II, 824H, D10R, D10T
1627757
HEAD
844, 844H, 854G, 854K, D11N, D11R, D11T
844, 844H, 854G, 854K, D11N, D11R, D11T
1009965
HEAD
854G, D10N, D10R, D10T, D9N
854G, D10N, D10R, D10T, D9N
1646497
HEAD
854G, 854K, D11N, D11R, D11T
854G, 854K, D11N, D11R, D11T
1422723
HEAD
D10N, D10R
D10N, D10R
6E3667
HEAD
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
6E6199
HEAD
D10N, D10R
D10N, D10R
9T4447
HEAD AS
D10N, D10R, D10T, D9L
D10N, D10R, D10T, D9L
3989666
HEAD
D10T
D10T
2476304
HEAD AS
D10N, D10R, D10T
D10N, D10R, D10T
2476306
HEAD
D10N, D10R, D10T
D10N, D10R, D10T
2476402
HEAD-MOTOR
D10N, D10R, D10T, D11R, D11T
D10N, D10R, D10T, D11R, D11T
2481381
HEAD
834H
834H
1627757
HEAD
844, 844H, 854G, 854K, D11N, D11R, D11T
844, 844H, 854G, 854K, D11N, D11R, D11T
6E5702
HEAD
D11N, D11R, D11T
D11N, D11R, D11T
3342648
HEAD
D11N, D11R, D11T
D11N, D11R, D11T
1627487
HEAD
824G II, 824H, D10R, D10T
824G II, 824H, D10R, D10T
1636474
HEAD
D8R, D8R II, D8T
D8R, D8R II, D8T
9T5819
HEAD
D11N, D11R
D11N, D11R
1013999
HEAD
D11N, D11R
D11N, D11R
9T4929
HEAD
D10, D11N
D10, D11N
6E3290
HEAD
D4HTSK III
D4HTSK III
9T6544
HEAD
824C, 826C
824C, 826C
1009965
HEAD
854G, D10N, D10R, D10T, D9N
854G, D10N, D10R, D10T, D9N