2058622 HEAD Caterpillar parts
325B L, 325C, 325C L, 325D, 325D L, 325D MH, M325B, M325C MH, M325D L MH, M330D
Rating:
Alternative (cross code) number:
CA2058622
205-8622
2058622
CA2058622
205-8622
2058622
Weight: 48 pounds 21 kg.
Information:
FLANGE SIZE
230
INSERT DIAMETER
149.88
INSERT LENGTH
33
INSIDE DIAMETER
105.63
PORT LOCATION
120
QUANTITY OF HOLES
8
PORT SIZE
25.0
EXCAVATOR, WHEELED EXCAVATOR,
Compatible equipment models: 2058622:
Number on catalog scheme:
1
For full view, you need register
Information:
Which Generate This Code:The ECM detects the following condition:
The aftercooler temperature is greater than 88 °C (190 °F) for 4 seconds.
The diagnostic codes 279-03 and 279-04 are not active.System Response:The ECM will log the event. The warning is deactivated if the temperature decreases below 84 °C (183 °F) for 2 seconds.
None
There may be a problem with the aftercooler.
There may be a problem with the aftercooler temperature sensor.Test Step 1. Check for Diagnostic Codes.
Connect ET to the service tool connector.
Turn the keyswitch to the ON position. The engine should be OFF.
Check for any Active Diagnostic Codes or Logged Diagnostic Codes.Expected Result:There should be no diagnostic codes that are present.Results:
OK - There are no diagnostic codes that are present. Proceed to Test Step 2.
Not OK - There are diagnostic codes that are present.Repair: Repair the diagnostic codes that are present. Refer to the appropriate topic in the "Troubleshooting With a Diagnostic Code" section of this manual. Ensure that the repair eliminates the problem. Stop.Test Step 2. Perform a Check of the Cooling System.
Perform a check of the cooling system. Refer to Troubleshooting, "Coolant Temperature is Too High" for possible causes.Expected Result:There are no problems with the cooling system.Results:
OK - There may be an intermittent problem.Repair: Monitor the operation of the engine. Repair the problem. Ensure that the repair eliminates the problem. Stop.
Not OK - There is a problem with the cooling system.Repair: Repair the problem. Ensure that the repair eliminates the problem. Stop.
The aftercooler temperature is greater than 88 °C (190 °F) for 4 seconds.
The diagnostic codes 279-03 and 279-04 are not active.System Response:The ECM will log the event. The warning is deactivated if the temperature decreases below 84 °C (183 °F) for 2 seconds.
None
There may be a problem with the aftercooler.
There may be a problem with the aftercooler temperature sensor.Test Step 1. Check for Diagnostic Codes.
Connect ET to the service tool connector.
Turn the keyswitch to the ON position. The engine should be OFF.
Check for any Active Diagnostic Codes or Logged Diagnostic Codes.Expected Result:There should be no diagnostic codes that are present.Results:
OK - There are no diagnostic codes that are present. Proceed to Test Step 2.
Not OK - There are diagnostic codes that are present.Repair: Repair the diagnostic codes that are present. Refer to the appropriate topic in the "Troubleshooting With a Diagnostic Code" section of this manual. Ensure that the repair eliminates the problem. Stop.Test Step 2. Perform a Check of the Cooling System.
Perform a check of the cooling system. Refer to Troubleshooting, "Coolant Temperature is Too High" for possible causes.Expected Result:There are no problems with the cooling system.Results:
OK - There may be an intermittent problem.Repair: Monitor the operation of the engine. Repair the problem. Ensure that the repair eliminates the problem. Stop.
Not OK - There is a problem with the cooling system.Repair: Repair the problem. Ensure that the repair eliminates the problem. Stop.
Caterpillar parts catalog:
Parts head Caterpillar catalog:
3045531
HEAD AS-GRAPPLE
GLC85
GLC85
3040499
HEAD AS-GRAPPLE
GLC85
GLC85
3163314
HEAD
120M, 120M 2, 12M
120M, 120M 2, 12M
2669967
HEAD
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD
2667376
HEAD
14M
14M
2491005
HEAD
GLS63
GLS63
3465611
HEAD
PIN GRAB
PIN GRAB
3465600
HEAD
336E, 336E L, 345D L, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 374D L, PIN GRAB
336E, 336E L, 345D L, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 374D L, PIN GRAB
1846015
HEAD GP-PUMP
330D L, 330D MH, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L
330D L, 330D MH, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L
8T6676
HEAD-FLANGE
TA19-M2WD
TA19-M2WD
2716377
HEAD AS
325C, 328D LCR, 330C, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L
325C, 328D LCR, 330C, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L
2255309
HEAD
330C, 330C L, 330D, 330D L, 330D LN, 336D L
330C, 330C L, 330D, 330D L, 330D LN, 336D L