AVSPARE.COM
parts catalog

HEAD 3236672 - Caterpillar



3236672 HEAD Caterpillar parts HEAD
Rating:
16
Alternative (cross code) number:
CA3236672
323-6672
3236672
Caterpillar 3236672 HEAD
Weight: 2 pounds 1 kg.

Buy HEAD 3236672 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g00727748
Typical example
Remove lip seal (1) from the bore at the pin joint for the heel.
Illustration 2 g00727752
Typical example
Attach Tooling (A) to sleeve bearing (2) (not shown) at the pin joint for the heel.
Attach a suitable lifting device to Tooling (A).
Use Tooling (A) to remove sleeve bearing (2).
Repeat Steps 1 through 4 to remove the lip seal and the sleeve bearing from the opposite side of the stick.
Illustration 3 g01371978
Typical example
Illustration 4 g01702833
Remove lip seal (3) from the bore for the boom pin.
Attach Tooling (B) to sleeve bearing (4) (not shown) at the pin joint for the boom end of the stick.
Attach a suitable lifting device to Tooling (B).
Use Tooling (B) to remove sleeve bearing (4).
Repeat Steps 6 through 9 to remove the lip seal and sleeve bearing from the opposite side of the stick.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
C 9U-5338 Bearing Puller Adapter 1
4C-9634 Puller Stud 1
9U-6832 Nut 1
6V-3175 Double Acting Cylinder 1
350-7768 Electric Hydraulic Pump Gp (115V) 1
350-7769 Electric Hydraulic Pump Gp (230V) 1
D 1P-0520 Driver Gp 1
E 9U-5337 Bearing Puller Adapter 1
4C-9634 Puller Stud 1
9U-6832 Nut 1
6V-3175 Double Acting Cylinder 1
350-7768 Electric Hydraulic Pump Gp (115V) 1
350-7769 Electric Hydraulic Pump Gp (115V) 1
Illustration 5 g01703773
Lower the temperature of sleeve bearing (4). Use Tooling (C) to install sleeve bearing (4) in the bore for the boom pin. Install sleeve bearing (4) until Dimension (d) is 9.5 0.8 mm (0.37 0.03 inch) below the outside surface of the stick.Note: Be sure that the pin bore in the stick is clean prior to installation of the bearings and lip seals.
Illustration 6 g01704575
Use Tooling (D) to install lip seal (3). Install lip seal (3) with the sealing lip toward the outside of the stick. Install lip seal (3) until contact is made with sleeve bearing (4).
Repeat Steps 1 and 2 for the opposite side of the stick.
Illustration 7 g01704615
Lower the temperature of sleeve bearing (2). Use Tooling (E) to install sleeve bearing (2) in the stick at the pin joint for the heel. Install sleeve bearing (2) in the pin bore until Dimension (a) is 7.5 0.8 mm (0.30 0.03 inch).Note: Be sure that the pin bore in the stick is clean prior to installation of the bearings and lip seals.
Illustration 8 g01704933
Use Tooling (D) to install lip seal (1) in the stick at the pin joint for the heel. Install lip seal (1) until contact is made with sleeve bearing (2).
Repeat Steps 4 and 5 for the opposite side of the stick.End By:
Install the stick.


Parts head Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.