6J8319 HEAD Caterpillar parts
10, 8D, D11N, D8K, D8L, D9L
Rating:
Alternative (cross code) number:
CA6J8319
6J-8319
6J8319
CA6J8319
6J-8319
6J8319
Weight: 57 pounds 25 kg.
RIPPER, TRACK-TYPE TRACTOR,
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1 Start By:
Remove the engine balancer shaft on 3114 engines. Refer to Disassembly and Assembly, "Engine Balancer Shaft - Remove and Install".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00610152
Remove bolts (1) that hold crankshaft main bearing cap (2). Remove crankshaft main bearing cap (2).
Remove the lower half of the crankshaft main bearing from crankshaft main bearing cap (2).
Illustration 2 g00516920
If the crankshaft is turned in the wrong direction, the tab of the crankshaft main bearing will be pushed between the crankshaft and the cylinder block. this can cause damage to either or both the crankshaft and the cylinder block.
Note: Some crankshaft main bearing journals do not have an oil hole. Place a thin piece of soft material that will not damage the journal against the end of the bearing. Ensure that the material is on the opposite side of the bearing tab. Hit the bearing with the soft material until the bearing tab is free from the bearing tab groove in the cylinder block.
Use the following steps in order to remove the upper half of crankshaft main bearings:
Turn the crankshaft until Tooling (A) can be installed in the crankshaft journal. Install Tooling (A).
Turn the crankshaft in order to remove the upper half of the crankshaft main bearing. In order to get the tab out first, the crankshaft must be turned in the correct direction.
Check the condition of the crankshaft main bearings. Refer to the Guideline For Reusable Parts, SEBF8009, "Main and Connecting Rod Bearings" and Guideline For Reusable Parts, SEBV0544, "Engine Bearings and Crankshafts".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1 Start By:
Remove the engine balancer shaft on 3114 engines. Refer to Disassembly and Assembly, "Engine Balancer Shaft - Remove and Install".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00610152
Remove bolts (1) that hold crankshaft main bearing cap (2). Remove crankshaft main bearing cap (2).
Remove the lower half of the crankshaft main bearing from crankshaft main bearing cap (2).
Illustration 2 g00516920
If the crankshaft is turned in the wrong direction, the tab of the crankshaft main bearing will be pushed between the crankshaft and the cylinder block. this can cause damage to either or both the crankshaft and the cylinder block.
Note: Some crankshaft main bearing journals do not have an oil hole. Place a thin piece of soft material that will not damage the journal against the end of the bearing. Ensure that the material is on the opposite side of the bearing tab. Hit the bearing with the soft material until the bearing tab is free from the bearing tab groove in the cylinder block.
Use the following steps in order to remove the upper half of crankshaft main bearings:
Turn the crankshaft until Tooling (A) can be installed in the crankshaft journal. Install Tooling (A).
Turn the crankshaft in order to remove the upper half of the crankshaft main bearing. In order to get the tab out first, the crankshaft must be turned in the correct direction.
Check the condition of the crankshaft main bearings. Refer to the Guideline For Reusable Parts, SEBF8009, "Main and Connecting Rod Bearings" and Guideline For Reusable Parts, SEBV0544, "Engine Bearings and Crankshafts".
Caterpillar parts catalog:
Parts head Caterpillar catalog:
9T3508
HEAD
980C, 980F, 980F II, D8L, D8N, R1600, R1600G, R1600H
980C, 980F, 980F II, D8L, D8N, R1600, R1600G, R1600H
1646403
HEAD
D8L, D9N, D9R, D9T
D8L, D9N, D9R, D9T
4T5113
HEAD
D9L
D9L
4T2575
HEAD
D10, D11N
D10, D11N
4T4256
HEAD
D9L
D9L
9T3505
HEAD
D10, D10N, D11N, D8L, D9L
D10, D10N, D11N, D8L, D9L
9T2828
HEAD
D8L, D9N
D8L, D9N
9T1851
HEAD
D9L
D9L
9T3504
HEAD
D10N, D9L
D10N, D9L
9T4434
HEAD
D10N, D9L
D10N, D9L
9T5271
HEAD
D11N
D11N
1003048
HEAD
D11N
D11N
5J9883
HEAD
977K, 977L
977K, 977L
9F1723
HEAD
44
44
6J9325
HEAD
631C, 633, 8A, 966C
631C, 633, 8A, 966C
4J7994
HEAD
631C, 633, 8A, 966C, 977
631C, 633, 8A, 966C, 977
1H0827
HEAD
44
44
5J7069
HEAD
8A, D7F, D7G
8A, D7F, D7G
9J5483
HEAD
776, 966C, 983
776, 966C, 983
8J6047
HEAD
983, 983B
983, 983B
6J1163
HEAD
973, 977K, 977L
973, 977K, 977L
2P1711
HEAD ASSEM.
814, 951B, 966C, D4D, D5
814, 951B, 966C, D4D, D5
2P1710
HEAD ASSEM.
814, 951B, 966C, D4D, D5
814, 951B, 966C, D4D, D5
2J3859
HEAD
4S, D4E
4S, D4E