7J6475 HEAD Caterpillar parts
941, 943, 953
Rating:
Alternative (cross code) number:
CA7J6475
7J-6475
7J6475
CA7J6475
7J-6475
7J6475
Weight: 14 pounds 6 kg.
Information:
FLANGE SIZE
141.27
INSERT DIAMETER
101.52
INSERT LENGTH
25.4
INSIDE DIAMETER
51.08
PORT LOCATION
73.03
QUANTITY OF HOLES
4
PORT SIZE
19
TRACK LOADER,
Information:
Illustration 1 g00483155 (1) Camshaft drive gears
Illustration 2 g01042492 (2) Idler gears Backlash between the camshaft drive gears and the idler gears ... 0.160 to 0.795 mm (0.0063 to 0.0313 inch)Bore for bearing ... 150 0.02 mm (5.905 0.0008 inch) (A) Base diameter. ... 160 0.02 mm (6.299 0.0008 inch) (B) Depth of installed bearing in gear's bore ... 3.0 0.5 mm (0.118 0.02 inch) (C) Circular runout of the bearing bore established by the axis of the gear's base diameter. ... 0.13 mm (0.0051 inch) (D) Inner diameter of bearing bore after machining ... 150.002 .020 mm (5.9056 0.0008 inch) (E) Maximum roughness of machined bearing bore ... 0.8 micrometers (3) Small cluster idler gear Backlash between the idler gears and the small cluster idler gear ... 0.067 to 0.778 mm (0.0026 to 0.0306 inch) (4) Idler gear (5) Torque for the bolts that connect the idler gear to the small cluster idler gear ... 135 20 N m (100 15 lb ft) (6) Crankshaft gear Backlash between the idler gear and the crankshaft ... 0.216 to 0.949 mm (0.0085 to 0.0374 inch)
Illustration 3 g00483156 (7) Mounting bolts for the idler shafts Use the following procedure in order to tighten the mounting bolts for the idler shaft.
Illustration 4 g00483157
Use the following sequence in order to tighten and turn the bolts. Two idler shafts with 8 bolt patterns ... 1-5-3-7-2-6-4-8One idler shaft with 10 bolt pattern ... 1-6-3-8-5-10-7-2-9-4
Tighten the bolts. Torque ... 160 16 N m (120 12 lb ft)
Tighten each of the bolts for an additional 45 5 degrees. (8) Locking plate and bolts (9) Bolt that holds the camshaft drive gear in position Use the following procedure in order to install the camshaft drive gears:Note: Use the manual barring group to rotate the engine. The engine must be prelubed before rotating the crankshaft in order to perform service work. Rotating the crankshaft before prelube may cause damage to the crankshaft bearings if the mating surface is dry.
Rotate the engine to the Top Center position of the compression stroke for the number one cylinder. Install the crankshaft timing pin.
If the crankshaft timing pin location is missed, do not turn the flywheel in the opposite direction to install the crankshaft timing pin. If the crankshaft timing pin location is missed, repeat Step 1.
Install the camshaft timing pin.
Put the camshaft drive gear (1) in position on the camshaft. Install the plate and the bolt hand tight. Note: Make sure that the gear taper and the camshaft taper are clean and dry. Make sure that the gear taper and the camshaft taper are free of dirt, rust and lubricants.
To prevent the crankshaft from turning, engage the manual barring group. Tighten the locking guide. Torque ... 270 25 N m (200 18 lb ft)
Apply 4C-5591 Anti-Seize Compound to the threads and to the seating face of the bolt. Use a torque multiplier to tighten the camshaft bolt. Torque
Cat SIS web machinery list:
Parts head Caterpillar catalog:
3G4650
HEAD
943
943
9J9788
HEAD
943
943
8J5966
HEAD
814B, 916, 926, 953, IT28
814B, 916, 926, 953, IT28
4T0329
HEAD ASSEM.
943, 953
943, 953
1U2049
HEAD ASSEM.
953, 963
953, 963
4T3062
HEAD
943, 953, 953B
943, 953, 953B
1U0474
HEAD
953
953
9T4763
HEAD
517, 527, 814B, 814F, 814F II, 816F, 816F II, 916, 926, 926A, 953, D4HTSK II, D4HTSK III, D5HTSK II, G926
517, 527, 814B, 814F, 814F II, 816F, 816F II, 916, 926, 926A, 953, D4HTSK II, D4HTSK III, D5HTSK II, G926
9T6871
HEAD
953
953
3J2586
HEAD
9A
9A
6J9739
HEAD
140B, 14G, 16G, 621B, 623E, 627B, 627E, 785, 955K, 955L, 973, 977, D6H
140B, 14G, 16G, 621B, 623E, 627B, 627E, 785, 955K, 955L, 973, 977, D6H
2K2943
HEAD
977, 977D, 977H
977, 977D, 977H
6J6891
HEAD
966C, 983, 9A
966C, 983, 9A
6J7591
HEAD
977K
977K
2S4690
HEAD
621, 980, D9G
621, 980, D9G
6J9325
HEAD
631C, 633, 8A, 966C
631C, 633, 8A, 966C
4J7994
HEAD
631C, 633, 8A, 966C, 977
631C, 633, 8A, 966C, 977
1H0827
HEAD
44
44
5J7069
HEAD
8A, D7F, D7G
8A, D7F, D7G
2K3767
HEAD (L.H.)
955C, 955H
955C, 955H
2K3768
HEAD (R.H.)
955C, 955H
955C, 955H