2834620 HEATER GP-JACKET WATER Caterpillar parts
C6.6
Rating:
Alternative (cross code) number:
CA2834620
283-4620
2834620
CA2834620
283-4620
2834620
GENERATOR SET,
Compatible equipment models: 2834620:
Number on catalog scheme:
For full view, you need register
Information:
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
In extreme operation applications, oil leakage may occur from the final drive cover due to insufficient mounting capacity of the bolts. Solution
Inspect the final drive cover for your machine. If oil leaks have occurred, follow the procedure below to eliminate the oil leaks.Procedure
Illustration 1 g03818661
Remove the 16 existing 143-0811 Bolts (1) and 5p-8245 Hard Washers (2) .
Remove the final drive cover (3) .
Remove any oil or grease from the ring gear and final drive cover with a Caterpillar approved solvent.
Illustration 2 g03818679
(4) Sealant
Apply 8C-8422 Sealant to the mating surface of the final drive cover and the ring gear.
Illustration 3 g03818695
Note: Sealant diameter 3 mm (0.12 inch) to 4 mm (0.16 inch). Refer to Illustration 3
Install the new 143-0811 Bolts and 5p-8245 Hard Washers in order to install the final drive cover. Tighten the bolts to a torque of 50 5 N m (37 3.7 lb ft) plus an angle of 40 4 degrees.
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
In extreme operation applications, oil leakage may occur from the final drive cover due to insufficient mounting capacity of the bolts. Solution
Inspect the final drive cover for your machine. If oil leaks have occurred, follow the procedure below to eliminate the oil leaks.Procedure
Illustration 1 g03818661
Remove the 16 existing 143-0811 Bolts (1) and 5p-8245 Hard Washers (2) .
Remove the final drive cover (3) .
Remove any oil or grease from the ring gear and final drive cover with a Caterpillar approved solvent.
Illustration 2 g03818679
(4) Sealant
Apply 8C-8422 Sealant to the mating surface of the final drive cover and the ring gear.
Illustration 3 g03818695
Note: Sealant diameter 3 mm (0.12 inch) to 4 mm (0.16 inch). Refer to Illustration 3
Install the new 143-0811 Bolts and 5p-8245 Hard Washers in order to install the final drive cover. Tighten the bolts to a torque of 50 5 N m (37 3.7 lb ft) plus an angle of 40 4 degrees.
Caterpillar SIS machinery equipment:
Parts heater Caterpillar catalog:
3599644
HEATER GP-SPACE
C4.4, C6.6
C4.4, C6.6
3599645
HEATER GP-SPACE
C2.2, C4.4, C6.6
C2.2, C4.4, C6.6
4343831
HEATER AS-SPACE
C4.4, C6.6
C4.4, C6.6
2152417
HEATER AS
3054, 3056, C1.5, C2.2, C3.3, C4.4, C6.6
3054, 3056, C1.5, C2.2, C3.3, C4.4, C6.6
2152418
HEATER AS-SPACE
3054, 3056, C1.5, C2.2, C3.3, C4.4, C6.6
3054, 3056, C1.5, C2.2, C3.3, C4.4, C6.6
2400239
HEATER AS-SPACE
3406C, 3456, C15, C15 I6, C18, C18 I6, C6.6, C9
3406C, 3456, C15, C15 I6, C18, C18 I6, C6.6, C9
2400238
HEATER AS-SPACE
3406C, 3456, C13, C15, C15 I6, C18, C18 I6, C6.6, C9
3406C, 3456, C13, C15, C15 I6, C18, C18 I6, C6.6, C9
2584350
HEATER AR-CAB
272C, 297C, 299C
272C, 297C, 299C
2535391
HEATER GP-JACKET WATER
D3K XL, D4K XL, D5K LGP
D3K XL, D4K XL, D5K LGP
2974701
HEATER AR-CAB
906H, 907H, 908H
906H, 907H, 908H
3599645
HEATER GP-SPACE
C2.2, C4.4, C6.6
C2.2, C4.4, C6.6
3599644
HEATER GP-SPACE
C4.4, C6.6
C4.4, C6.6