HEATER GP-CAB 4419714 - Caterpillar

4419714 HEATER GP-CAB Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4419714
441-9714
4419714

Buy HEATER GP-CAB 4419714 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Replacement for 747-0710A Hinge Pin fits 116-088T131(44-1971-4)(1996) 11A-082A131(1997) 11A-088T131(1997)

$17.07

18 Apr 2024

US: snahud

Replacement for 747-0710A Hinge Pin fits 116-088T131(44-1971-4)(1996) 11A-082A131(1997) 11A-088T131(1997)
cbrsit 100% Brand New and high quality || Note: Please check the model before ordering. || High-quality Replacement || Packing quantity as the picture shows. || Replacement for 747-0710A Hinge Pin fits 116-088T131(44-1971-4)(1996) 11A-082A131(1997) 11A-088T131(1997)

Number on catalog scheme: 5

Caterpillar 4419714 Parts scheme HEATER GP-CAB

For full view, you need register

Information:

Illustration 1 g00770585
Circuit schematic for the wait to start lamp
Illustration 2 g00770189
Pin locations for ECM connector P1Test Step 1. Inspect Electrical Connectors and Wiring
Thoroughly inspect ECM vehicle harness connector J1/P1, the firewall bulkhead connector, or the wait to start lamp. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the wait to start lamp.Refer to Illustration 2.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and wiring for abrasion and pinch points from the battery to the ECM.Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasions or of pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.STOPTest Step 2. Check for Normal Operation of the "Wait to Start Lamp"
Connect Cat ET to the data link connector. Access the configuration screen and ensure that the "Wait to Start Lamp" parameter is programmed to "J1/P1:31".
Turn the ignition key switch to the OFF position for ten seconds. Turn the ignition key switch to the ON position.
The "Wait To Start Lamp" illuminates for approximately two seconds when the key switch is turned on. If conditions require the air inlet heater to turn on, the wait to start lamp remains illuminated until the air inlet heater turns off or the engine is started.Expected Result:The "Wait To Start Lamp" turns on and the "Wait To Start Lamp" turns off per the above description.Results:
Yes - The "Wait To Start Lamp" appears to operating correctly at this time.STOP
No - Proceed to Test Step 3.Test Step 3. Test the Circuit for the "Wait to Start Lamp"
Illustration 3 g00770210
Vehicle harness connector P1
Disconnect ECM vehicle harness connector J1/P1.
Fabricate a jumper wire 100 mm (4 inch) long. Crimp a Deutsch pin to both ends of the wire.
Insert the jumper into P1:31.
Connect the other end of the jumper wire to P1:65 (−battery).
Turn the ignition key switch to the ON position.
While the lamp is being watched, insert the jumper wire and remove the jumper wire.Refer to Illustration 3.Expected Result: The "Wait To Start Lamp" turns on while the jumper is connected to both sockets. Also, the "Wait To Start Lamp" turns off when the jumper is removed from one of the sockets.Result 2 Result 3 Results:
OK - The wait to start lamp is functioning properly. Proceed to Test Step 4.
Not OK