D5B LGP TRACTOR / POWER SHIFT / 46X00001-00723 (MACHINE) POWERED BY 3306 ENGINE ELECTRICAL AND STARTING SYSTEM Caterpillar SIS

TRACK-TYPE TRACTOR D5B TRACK-TYPE TRACTOR 46X
D5B LGP TRACTOR / POWER SHIFT / 46X00001-00723 (MACHINE) POWERED BY 3306 ENGINE HEBP1178 D5B 46X (1978)

Parts group D5B:

For full view, you need register

ELECTRICAL AND STARTING SYSTEM

ALTERNATOR GP-CHARGING

3A-3565 ALTERNATOR GROUP

3A3565 ALTERNATOR GROUP
--24 Volt, 19 Ampere
Serial No. 46X1 to 46X505 inclusive
3A1997 Alternator parts are shown on Page 70C
Note: 2P6140 Vee Belt Set, includes 2 belts, is used

9S-9546 ALTERNATOR ARRANGEMENT

9S9546 ALTERNATOR ARRANGEMENT
--24 Volt, 50 Ampere
Also part of 8P8286 Roll-Over Protective System Arrangement and 3A5369 Cab
Arrangement listed on Pages 157 and 158C.
AN ATTACHMENT

8S-4285 ALTERNATOR GROUP

8S4285 ALTERNATOR GROUP
--24 Volt, 50 Ampere
Part of 9S9546 Alternator Arrangement.
5S9088 Alternator parts are shown on Pages 72, 73, 73A and 73B.
AN ATTACHMENT

7N-8133 ALTERNATOR ARRANGEMENT

7N8133 ALTERNATOR ARRANGEMENT
--24 Volt, 50 Ampere--Replaced by
8N1084 shown on Page 70-1
Part of 3A5369 Cab Arrangement listed on Page 158C.
AN ATTACHMENT

6N-5471 ALTERNATOR GROUP

6N5471 ALTERNATOR GROUP
--24 Volt, 19 Ampere
Serial No. 46X506 to 46X680 inclusive. Also available as an attachment Serial No. 46X1
to 46X505 inclusive. 2P1204 Alternator parts are shown on Page 74

8N-1084 ALTERNATOR GROUP

8N1084 ALTERNATOR GROUP
--24 Volt, 50 Ampere
Part of 3A5369 Cab Arrangement listed on Page 158C-1
AN ATTACHMENT

6N-5471 ALTERNATOR GROUP

6N5471 ALTERNATOR GROUP
--24 Volt, 35 Ampere
Serial No. 46X681--Up
6N9294 Alternator parts are shown on Page 71A.
NOTE: 2P6140 Vee Belt Set, Includes 2 belts, is used

3A-5949 ALTERNATOR GROUP

3A5949 ALTERNATOR GROUP
--24 Volt, 35 Ampere
Serial No. 46X506--Up. 6N9294 Alternator parts are shown on Pages 70D and 71
AN ATTACHMENT

3A-4826 ALTERNATOR GROUP

3A4826 ALTERNATOR GROUP
--24 Volt, 19 Ampere--Type 1
Part of 3A5525 Sound Suppression Arrangement listed on Page 140A.
3A1997 Alternator parts are shown on Page 70C.
AN ATTACHMENT

3A-4826 ALTERNATOR GROUP

3A4826 ALTERNATOR GROUP
--24 Volt, 35 Ampere--Type 2
Part of 3A5525 Sound Suppression Arrangement listed on Page 140A
6N9294 Alternator parts are shown on Pages 70D and 71.
AN ATTACHMENT

3A-1997 ALTERNATOR GROUP

3A1997 ALTERNATOR GROUP
--24 Volt, 19 Ampere--paris rhone
Part of 3A3565 & 3A4826 Alternator Groups shown on Pages 68 and 70A

6N-9294 ALTERNATOR GROUP

6N9294 ALTERNATOR GROUP--Part 1 of 2
--24 Volt, 35 Ampere--Type 1
Part of 3A5949 & 3A4826 Alternator Groups shown on Pages 70A and 70B
AN ATTACHMENT

6N-9294 ALTERNATOR GROUP

6N9294 ALTERNATOR GROUP--Part 2 of 2
--24 Volt, 35 Ampere--Type 1
Part of 3A5949 & 3A4826 Alternator Groups shown on Pages 70A and 70B
AN ATTACHMENT

6N-9294 ALTERNATOR GROUP

6N9294 ALTERNATOR GROUP
--24 Volt, 35 Ampere--Type 2
Part of 6N5471, 3A5949 and 3A4826 Alternator Groups shown on
Pages 70-1, 70A and 70B

7N-9720 ALTERNATOR GROUP

7N9720 ALTERNATOR GROUP
--24 Volt, 35 Ampere--Type 1
Part of 6N9294 Alternator Group listed on Page 71A

7N-9720 ALTERNATOR GROUP

7N9720 ALTERNATOR GROUP
--24 Volt, 35 Ampere--Type 2
Part of 6N9294 Alternator Group listed on Page 71A

9G-8255 ALTERNATOR GROUP

9G8255 ALTERNATOR GROUP--Part 1 of 2
--Delco-Remy--24 Volt, 35 Ampere
Part of 6N9294 Alternator Group listed on Page 71A

9G-8255 ALTERNATOR GROUP

9G8255 ALTERNATOR GROUP--Part 2 of 2
--Delco-Remy--24 Volt, 35 Ampere
Part of 6N9294 Alternator Group listed on Page 71A

5S-9088 ALTERNATOR ASSEMBLY

5S9088 ALTERNATOR ASSEMBLY--Part 1 of 2
--24 Volt, 50 Ampere--Type 1
Part of 8S4285,7N8133 and 8N1084 Alternator Groups shown on Pages 69, 70 and 70-1.
AN ATTACHMENT

5S-9088 ALTERNATOR ASSEMBLY

5S9088 ALTERNATOR ASSEMBLY--Part 2 of 2
--24 Volt, 50 Ampere--Type 1
Part of 8S4285,7N8133 and 8N1084 Alternator Groups shown on Pages 69, 70 and 70-1.
AN ATTACHMENT

5S-9088 ALTERNATOR ASSEMBLY

5S9088 ALTERNATOR ASSEMBLY--Part 1 of 2
--24 Volt, 50 Ampere--Type 2
Part of 8S4285,7N8133 and 8N1084 Alternator Groups shown on Pages 69, 70 and 70-1.
AN ATTACHMENT

5S-9088 ALTERNATOR ASSEMBLY

5S9088 ALTERNATOR ASSEMBLY
--24 Volt, 50 Ampere--Type 2
Part of 8S4285,7N8133 and 8N1084 Alternator Groups shown on Pages 69, 70 and 70-1.
AN ATTACHMENT

5S-9088 ALTERNATOR ASSEMBLY

5S9088 ALTERNATOR ASSEMBLY
--24 Volt, 50 Ampere--Type 3
Part of 8S4285,7N8133 & 8N1084 Alternator Groups listed on Pages 69, 70 & 70-1
AN ATTACHMENT

2P-1204 ALTERNATOR GROUP

2P1204 ALTERNATOR GROUP
--24 Volt, 19 Ampere--Prestolite
Part of 6N5471 Charging Alternator Group shown on Page 70

9G-9538 ALTERNATOR GROUP

9G9538 ALTERNATOR GROUP
--24 Volt, 50 Ampere
Part of 5S9088 Alternator Assembly listed on Page 73B-2
AN ATTACHMENT

3T-1888 ALTERNATOR GROUP

3T1888 ALTERNATOR GROUP--Part 1 of 2
--Delco-Remy--24 Volt, 50 Ampere
Part of 5S9088 Alternator Assembly listed on Page 73B-2
AN ATTACHMENT

3T-1888 ALTERNATOR GROUP

3T1888 ALTERNATOR GROUP--Part 2 of 2
--Delco-Remy--24 Volt, 50 Ampere
Part of 5S9088 Alternator Assembly listed on Page 73B-2
AN ATTACHMENT

BATTERY GP

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 1 of 3
--24 Volt--Top View
Serial No. 46X1 to 46X406 inclusive
7N718 Switch parts are shown on Page 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 2 of 3
--24 Volt--Top View
Serial No. 46X1 to 46X406 inclusive
8P4698 and 8P4700 Harness parts are shown on Pages 66 and 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 3 of 3
--24 Volt--Top View
Serial No. 46X1 to 46X406 inclusive
8P4699 Harness parts are shown on Page 66

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 1 of 3
--24 Volt--Top View
Serial No. 46X407 to 46X628 inclusive.
7N718 Switch parts are shown on Page 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 2 of 3
--24 Volt--Top View
Serial No. 46X407 to 46X628 inclusive.
8P4698 and 8P4700 Harness parts are shown on Pages 66 and 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 3 of 3
--24 Volt--Top View
Serial No. 46X407 to 46X628 inclusive.
8P4699 Harness parts are shown on Page 66

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 1 of 3
--24 Volt--Top View
Serial No. 46X629-Up.
7N718 Switch parts are shown on Page 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 2 of 3
--24 Volt--Top View
Serial No. 46X629--Up.
7G7285 and 8P4700 Harness parts are shown on Pages 65F and 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 3 of 3
--24 Volt--Top View
Serial No. 46X629--Up.
8P4699 Harness parts are shown on Page 66

GLOW PLUG GP

5S-8501 GLOW PLUG AND WIRING GROUP

5S8501 GLOW PLUG AND WIRING GROUP
--24 Volt

LIGHTING GP

8P-6565 LIGHTING GROUP

8P6565 LIGHTING GROUP
--4 Lamp--24 Volt
FOR USE WITH OPEN ROPS.
AN ATTACHMENT

8P-6566 LIGHTING GROUP

8P6566 LIGHTING GROUP
--4 Lamp--24 Volt--Type 1
FOR USE WITHOUT ROPS.
AN ATTACHMENT

8P-6566 LIGHTING GROUP

8P6566 LIGHTING GROUP
-4 Lamp-24 Volt-Type 2
FOR USE WITHOUT ROPS.
AN ATTACHMENT

3A-5251 LIGHTING GROUP

3A5251 LIGHTING GROUP
-24 Volt-Without Lamps
FOR USE WITH ENCLOSED ROPS
AN ATTACHMENT

3A-5136 LIGHTING GROUP

3A5136 LIGHTING GROUP
-24 Volt-Without Lamps
FOR USE WITH OPEN ROPS
AN ATTACHMENT

9P-2068 LIGHTING GROUP

9P2068 LIGHTING GROUP
-4 Lamp-24 Volt
FOR USE WITH OPEN ROPS AND SWEEP
1M1882 Lamp parts are shown on Page 95.
AN ATTACHMENT

9P-3696 LIGHTING GROUP

9P3696 LIGHTING GROUP
-4 Lamp-24 Volt
FOR USE WITH ENCLOSED ROPS AND SWEEP
1M1882 Lamp parts are shown on Page 95.
AN ATTACHMENT

9P-3384 LIGHTING GROUP

9P3384 LIGHTING GROUP
-4 Lamp-24 Volt
Also part of 3A5369 Cab Arrangement listed on Page 158C
FOR USE WITH ENCLOSED ROPS.
AN ATTACHMENT

3A-5491 LIGHTING SYSTEM GROUP

3A5491 LIGHTING SYSTEM GROUP
-4 Lamp-24 Volt-FOR USE WITH ENCLOSED ROPS
Part of 3A5369 Cab Arrangement listed on Page 158C.
AN ATTACHMENT

8A-3048 LIGHTING GROUP

8A3048 LIGHTING GROUP
-Without Lamps-24 Volt-FOR USE WITH ENCLOSED ROPS
Part of 8A3043 ROPS Arrangement listed on Page 157.
AN ATTACHMENT

3A-5553 LIGHTING GROUP

3A5553 LIGHTING GROUP
--4 Lamp--24 Volt
FOR USE WITH OPEN ROPS.
Part of 3A5368 ROPS Arrangement listed on Page 158D
AN ATTACHMENT

8A-3060 LIGHTING GROUP

8A3060 LIGHTING GROUP
--Without Lamp--24 Volt
FOR USE WITH OPEN ROPS
Part of 8A3058 Roll-Over Protective System Group shown on Page 158E

1M-1882 FLOOD LAMP ASSEMBLY

1M1882 FLOOD LAMP ASSEMBLY
--24 Volt
Part of 9P2068 and 9P3696 Lighting Groups shown on Pages 92 and 93
AN ATTACHMENT

STARTING AR

3A-1872 ELECTRIC STARTING MOTOR ASSEMBLY

3A1872 ELECTRIC STARTING MOTOR ASSEMBLY--Part 1 of 2
--24 Volt
Part of 3A1590 Electric Starting Motor Group shown on Page 75

3A-1872 ELECTRIC STARTING MOTOR ASSEMBLY

3A1872 ELECTRIC STARTING MOTOR ASSEMBLY--Part 2 of 2
--24 Volt
Part of 3A1590 Electric Starting Motor Group shown on Page 75

STARTING MOTOR GP

3A-1590 ELECTRIC STARTING MOTOR GROUP

3A1590 ELECTRIC STARTING MOTOR GROUP
--24 Volt
Serial No. 46X1 to 46X505 inclusive
3A1872 Motor parts are shown on Pages 82 and 83

7S-3622 ELECTRIC STARTING MOTOR GROUP

7S3622 ELECTRIC STARTING MOTOR GROUP
--24 Volt
Serial No. 46X506 to 46X699 inclusive. Also available as an attachment at Serial No.
46X1 to 46X505 inclusive. 4N3182 and 4N7752 Motor parts are shown on Pages 77 through 81

8S-3886 ELECTRIC STARTING MOTOR GROUP

8S3886 ELECTRIC STARTING MOTOR GROUP
--24 Volt
FOR USE IN TEMPERATURES OF -18 Degrees C (0 Degrees F) OR BELOW
2P3926 Motor parts are shown on Pages 84, 85 and 86.
AN ATTACHMENT

7S-3622 ELECTRIC STARTING MOTOR GROUP

7S3622 ELECTRIC STARTING MOTOR GROUP
--24 Volt
Serial No. 46X700--Up
Also available as an attachment at Serial No. 46X1 to 46X505 inclusive
4N3181 Motor parts are listed on Page 76A

4N-3181 ELECTRIC STARTING MOTOR GROUP

4N3181 ELECTRIC STARTING MOTOR GROUP
--24 Volt
Serial No. 46X700--Up
Part of 7S3622 Electric Starting Motor Group shown on Page 76A

4N-3182 ELECTRIC STARTING MOTOR GROUP

4N3182 ELECTRIC STARTING MOTOR GROUP--Part 1 of 3
--Delco-Remy--24 Volt
Part of 7S3622 & 4N3181 Electric Starting Motor Groups shown on Pages 75 & 76A
1P9181 Switch parts are shown on Page 86D

4N-3182 ELECTRIC STARTING MOTOR GROUP

4N3182 ELECTRIC STARTING MOTOR GROUP--Part 2 of 3
--Delco-Remy--24 Volt
Part of 7S3622 & 4N3181 Electric Starting Motor Groups shown on Pages 75 & 76A

4N-3182 ELECTRIC STARTING MOTOR GROUP

4N3182 ELECTRIC STARTING MOTOR GROUP--Part 3 of 3
--Delco-Remy--24 Volt
Part of 7S3622 & 4N3181 Electric Starting Motor Groups shown on Pages 75 & 76A

4N-7752 ELECTRIC STARTING MOTOR GROUP

4n7752 ELECTRIC STARTING MOTOR GROUP--Part 1 of 2
--Prestolite--24 Volt
Serial No. 46X1 to 46X699 inclusive.
Part of 7S3622 Electric Starting Motor Group shown on Page 75
9S7976 Switch parts are shown on Page 87

4N-7752 ELECTRIC STARTING MOTOR GROUP

4N7752 ELECTRIC STARTING MOTOR GROUP--Part 2 of 2
--Prestolite--24 Volt
Serial No. 46X1 to 46X699 inclusive
Part of 7S3622 Electric Starting Motor Group shown on Page 75

9G-4338 ELECTRIC STARTING MOTOR GROUP

9G4338 ELECTRIC STARTING MOTOR GROUP--24 Volt--Prestolite--Part 1
Serial No. 46X700--Up
Part of 4N3181 Electric Starting Motor Group shown on Page 76A. 9S7976 Switch parts are shown on Page 87

9G-4338 ELECTRIC STARTING MOTOR GROUP

9G4338 ELECTRIC STARTING MOTOR GROUP--24 Volt--Prestolite--Part 2
Serial No. 46X700--Up
Part of 4N3181 Electric Starting Motor Group shown on Page 76A

2P-3926 ELECTRIC STARTING MOTOR GROUP

2P3926 ELECTRIC STARTING MOTOR GROUP--Part 1 of 3
--24 Volt--Type 1
FOR USE IN TEMPERATURE OF -18 DEGREES C (0 DEGREES F) OR BELOW.
Part of 8S3886 Electric Starting Motor Group shown on Page 76.
6N5123 Switch parts are shown on Page 87.
AN ATTACHMENT

2P-3926 ELECTRIC STARTING MOTOR GROUP

2P3926 ELECTRIC STARTING MOTOR GROUP--Part 2 of 3
--24 Volt--Type 1
FOR USE IN TEMPERATURES OF -18 DEGREES C (0 DEGREES F) OR BELOW
Part of 8S3886 Electric Starting Motor Group shown on Page 76.
AN ATTACHMENT

2P-3926 ELECTRIC STARTING MOTOR GROUP

2P3926 ELECTRIC STARTING MOTOR GROUP--Part 3 of 3
--24 Volt--Type 1
FOR USE IN TEMPERATURES OF -18 DEGREES C (0 DEGREES F) OR BELOW
Part of 8S3886 Electric Starting Motor Group shown on Page 76.
AN ATTACHMENT

2P-3926 ELECTRIC STARTING MOTOR GROUP

2P3926 ELECTRIC STARTING MOTOR GROUP--Part 1 of 3
--24 Volt--Type 2
FOR USE IN TEMPERATURES OF -18 DEGREES C (0 DEGREES F) OR BELOW.
Part of 8S3886 Electric Motor Group shown on Page 76.
4M1812 Switch parts are shown on page 86D.
AN ATTACHMENT

2P-3926 ELECTRIC STARTING MOTOR GROUP

2P3926 ELECTRIC STARTING MOTOR GROUP--Part 2 of 3
--24 Volt--Type 2
FOR USE IN TEMPERATURES OF -18 DEGREES C (0 DEGREES F) OR BELOW
Part of 8S3886 Electric Starting Motor Group shown on Page 76.
AN ATTACHMENT

2P-3926 ELECTRIC STARTING MOTOR GROUP

2P3926 ELECTRIC STARTING MOTOR GROUP--Part 3 of 3
--24 Volt--Type 2
FOR USE IN TEMPERATURES OF -18 DEGREES C (0 DEGREES F) OR BELOW
Part of 8S3886 Electric Starting Motor Group shown on Page 76.
AN ATTACHMENT

SWITCH GP

7N-0718 DISCONNECT SWITCH ASSEMBLY

7N718 DISCONNECT SWITCH ASSEMBLY
Part of 8P4711 Battery and Wiring Group shown on Pages 62, 65 & 65C

4M-1812 SOLENOID SWITCH ASSEMBLY

4M1812 SOLENOID SWITCH ASSEMBLY
Part of 2P3926 Electric Starting Motor Group shown on Page 86A
AN ATTACHMENT

1P-9181 SOLENOID SWITCH ASSEMBLY

1P9181 SOLENOID SWITCH ASSEMBLY
Part of 4N3182 Electric Starting Motor Group shown on Page 77
AN ATTACHMENT

9S-7976 SOLENOID SWITCH ASSEMBLY

9S7976 SOLENOID SWITCH ASSEMBLY
--24 Volt
Part of 4N7752 & 9G4338 Electric Starting Motor Groups shown on Pages 80 & 81A

6N-5123 SOLENOID SWITCH ASSEMBLY

6N5123 SOLENOID SWITCH ASSEMBLY
--24 Volt--Replaced by
4M1812 Shown on Page 86D
Part of 2P3926 Electric Starting Motor Group shown on Page 84.
AN ATTACHMENT

4N-8985 COOLANT FLOW SWITCH GROUP

4N8985 COOLANT FLOW SWITCH GROUP
AN ATTACHMENT

WARNING GP

9P-8012 BACK-UP WARNING GROUP

9P8012 BACK-UP WARNING GROUP
--Type 1
AN ATTACHMENT

9P-8012 BACK-UP WARNING GROUP

9P8012 BACK-UP WARNING GROUP
--Type 2
AN ATTACHMENT

WIRING GP

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 1 of 3
--24 Volt--Top View
Serial No. 46X1 to 46X406 inclusive
7N718 Switch parts are shown on Page 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 2 of 3
--24 Volt--Top View
Serial No. 46X1 to 46X406 inclusive
8P4698 and 8P4700 Harness parts are shown on Pages 66 and 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 3 of 3
--24 Volt--Top View
Serial No. 46X1 to 46X406 inclusive
8P4699 Harness parts are shown on Page 66

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 1 of 3
--24 Volt--Top View
Serial No. 46X407 to 46X628 inclusive.
7N718 Switch parts are shown on Page 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 2 of 3
--24 Volt--Top View
Serial No. 46X407 to 46X628 inclusive.
8P4698 and 8P4700 Harness parts are shown on Pages 66 and 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 3 of 3
--24 Volt--Top View
Serial No. 46X407 to 46X628 inclusive.
8P4699 Harness parts are shown on Page 66

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 1 of 3
--24 Volt--Top View
Serial No. 46X629-Up.
7N718 Switch parts are shown on Page 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 2 of 3
--24 Volt--Top View
Serial No. 46X629--Up.
7G7285 and 8P4700 Harness parts are shown on Pages 65F and 67

8P-4711 BATTERY AND WIRING GROUP

8P4711 BATTERY AND WIRING GROUP--Part 3 of 3
--24 Volt--Top View
Serial No. 46X629--Up.
8P4699 Harness parts are shown on Page 66

7G-7285 HARNESS ASSEMBLY

7G7285 HARNESS ASSEMBLY
Serial No. 46X629--Up
Part of 8P4711 Battery and Wiring Group shown on Page 65D

8P-4698 HARNESS ASSEMBLY

8P4698 HARNESS ASSEMBLY
Serial No. 46X1 to 46X628 inclusive
Part of 8P4711 Battery and Wiring Group shown on Pages 63 & 65A

8P-4699 HARNESS ASSEMBLY

8P4699 HARNESS ASSEMBLY
Part of 8P4711 Battery and Wiring Group shown on Pages 64, 65B & 65E

8P-4700 HARNESS ASSEMBLY

8P4700 HARNESS ASSEMBLY
Part of 8P4711 Battery and Wiring Group shown on Pages 63, 65A & 65D

5S-8501 GLOW PLUG AND WIRING GROUP

5S8501 GLOW PLUG AND WIRING GROUP
--24 Volt

8P-6128 HARNESS ASSEMBLY

8P6128 HARNESS ASSEMBLY
--Replaced by 9G3717 shown on Page 167A
Part of 8P2131 Cab Pressurizer Group shown on Pages 162, 164A & 164D
AN ATTACHMENT

8P-6368 HARNESS ASSEMBLY

8P6368 HARNESS ASSEMBLY
Part of 8P2131 Cab Pressurizer Group shown on Pages 163, 164B, 164E & 164H
AN ATTACHMENT

9G-3717 HARNESS ASSEMBLY

9G3717 HARNESS ASSEMBLY
Part of 8P2131 Cab Pressurizer Group shown on Page 164G
AN ATTACHMENT

9P-2045 COMPRESSOR HARNESS ASSEMBLY

9P2045 COMPRESSOR HARNESS ASSEMBLY
Part of 8P2144, 7G9699 and 9P5228 Air Conditioner Arrangements listed on Pages
182, 182B and 183. AN ATTACHMENT

HEATER GP

4N-3586 JACKET WATER HEATER GROUP

4N3586 JACKET WATER HEATER GROUP
AN ATTACHMENT

Information:

(For parts list, see above)

ELECTRICAL AND STARTING SYSTEM

THERMOCOUPLE GP

Special Instruction

Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}
Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}

ALARM GP

Installation of 244-1090 Alarm Gp {7400, 7402, 7407}
Installation of 244-1090 Alarm Gp {7400, 7402, 7407}

Installation of 262-6141 Alarm Gp {7406}
Installation of 262-6141 Alarm Gp {7406}

Disassembly and Assembly

Back-Up Warning Alarm And Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

ALTERNATOR GP-CHARGING

Engine News

Repair Parts Available for Alternator R-Terminal {1405}
2000/12/01

Harness Repair of Alternator R-Terminal Connector {1405}
2000/12/01

Charging System Troubleshooting Guide Has Been Updated for All Engines {1406, 7569}
Charging System Troubleshooting Guide Has Been Updated for All Engines {1406, 7569}

Special Instruction

Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}

Charging System Troubleshooting {1406}
Charging System Troubleshooting {1406}

Procedure for Replacing Regulator Kit on All Engines {1405}
Procedure for Replacing Regulator Kit on All Engines {1405}

Procedure to Install Brush Holder Assembly to End Frame on All Engines {1405}
Procedure to Install Brush Holder Assembly to End Frame on All Engines {1405}

Specifications

Alternators
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Alternator Regulator
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Alternator
DELCO REMY 20-SI SERIES ALTERNATOR

Alternator and Regulator
3306C Engines for Caterpillar Built Machines

Systems Operation

Systems Operation
DELCO REMY 20-SI SERIES ALTERNATOR

Testing and Adjusting

Testing And Adjusting
DELCO REMY 20-SI SERIES ALTERNATOR

Charging System - Test
3306C Engines for Caterpillar Built Machines

Troubleshooting

MID 161 - CID 0168 - FMI 00
Product Link - PL522/523

MID 161 - CID 0168 - FMI 01
Product Link - PL522/523

MID 161 - CID 1251 - FMI 03
Product Link - PL522/523

MID 122 - CID 0168 - FMI 00
Product Link 121S/300

MID 122 - CID 0168 - FMI 01
Product Link 121S/300

MID 122 - CID 1251 - FMI 03
Product Link 121S/300

Disassembly and Assembly

Alternator
DELCO REMY 20-SI SERIES ALTERNATOR

Alternator
3306 VEHICULAR ENGINE FOR D5B TRACTORS

Service Magazine

New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23

Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01

Identification Of External Terminals On Alternators{1405,1406,1400}
1987/03/23

Alternator "R" Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04

Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04

Check Alternator Output Connection Prior To Machine Delivery{1405}
1987/05/18

Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25

Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23

8T5314 Socket Adapter Available To Correctly Install Alternator Pulley Nut {0601}
1988/01/25

New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13

Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22

Identification Of External Terminals On Alternators {1405,1406,1400}
1998/12/07

Repair Parts Available for Alternator R-Terminal {1405}
2000/10/02

Harness Repair of Alternator R-Terminal Connector {1405, 1408, 7553}
2000/10/02

Charging System Troubleshooting Guide Has Been Updated for All Machines {1406, 7569}
Charging System Troubleshooting Guide Has Been Updated for All Machines {1406, 7569}

BATTERY GP

Truck Engine News

Coolant/Battery Tester Group Quickly Tests Coolant and Battery Acid {0773, 0785}
2004/12/27

Engine News

Special Instruction

Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}

Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}

Installation Of 9G3 And 9G4 Battery Terminal Covers{1401}
Installation Of 9G3 And 9G4 Battery Terminal Covers{1401}

Use Of 6V3025 Battery Cable Repair Kit{0613, 1400}
Use Of 6V3025 Battery Cable Repair Kit{0613, 1400}

Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}

Service Letter-NACD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Technical Information Bulletin

Recommendations for Battery Charging and Temperatures for Machines and Generator Sets{1401, 751B}
Recommendations for Battery Charging and Temperatures for Machines and Generator Sets{1401, 751B}

Process for Communicating an Incident with a Battery{1401}
Process for Communicating an Incident with a Battery{1401}

Specifications

Coolant Flow Switch
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Starter Magnetic Switch
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Tool Operating Manual

M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}

M0090131 Battery Analyzer 480-4181 (484-4859 Group) {0374, 0599, 0709, 1401, 7468}
M0090131 Battery Analyzer 480-4181 (484-4859 Group) {0374, 0599, 0709, 1401, 7468}

Service Letter-China

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Asia

Service Letter-APD

Testing and Adjusting

Battery - Test
3306C Engines for Caterpillar Built Machines

Troubleshooting

MID 161 - CID 0168 - FMI 00
Product Link - PL522/523

MID 161 - CID 0168 - FMI 01
Product Link - PL522/523

MID 161 - CID 1251 - FMI 03
Product Link - PL522/523

MID 122 - CID 0168 - FMI 00
Product Link 121S/300

MID 122 - CID 0168 - FMI 01
Product Link 121S/300

MID 122 - CID 1251 - FMI 03
Product Link 121S/300

Disassembly and Assembly

Batteries
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Cab Liners, Disconnect Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Back-Up Warning Alarm And Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Service Magazine

New Horn Switch Available{7303}
1981/09/07

Maintenance Free Batteries{1401}
1986/03/10

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01

Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Identification Of External Terminals On Alternators{1405,1406,1400}
1987/03/23

Alternator "R" Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04

Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04

Testing The Starter On The Engine{1401,1450}
1987/05/04

Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14

Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29

Shorter Mounting Bolts Used For Glow Plug Wiring{1403,1412}
1979/05/21

New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13

Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26

High Performance Maintenance Free Battery Available{1401}
1989/01/16

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

Preventive Maintenance For Batteries{1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01

Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01

Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}
1989/06/19

Fitting Needed To Install New Oil Pressure Switch When Replacing Former Switches{7485}
1991/11/25

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

Identification Of External Terminals On Alternators {1405,1406,1400}
1998/12/07

Coolant/Battery Tester Group Quickly Tests Coolant and Battery Acid {0773, 0785}
2004/12/27

CIRCUIT BREAKER GP

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

CONTROL GP-ELECTRONIC

Special Instruction

Installation Of 9G4706 Ether Starting Aid Group For Direct Injection Engines{1456}
Installation Of 9G4706 Ether Starting Aid Group For Direct Injection Engines{1456}

Installation of Seat Belt Reminder Systems {1408, 1901, 1902, 7327, 7602, 7606, 7610, 7620}
Installation of Seat Belt Reminder Systems {1408, 1901, 1902, 7327, 7602, 7606, 7610, 7620}

Tool Operating Manual

Communication Adapter II{0600, 0709, 7600, 7610}
Communication Adapter II{0600, 0709, 7600, 7610}

Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}
Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}

Service Magazine

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

New Radio Software Is Now Available For Product Link 522 and 523 Radio On All Cat ® Products {7610, 7620}
2014/02/06

Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}
Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}

A New Handheld Digital Manometer is Now Available {7490}
A New Handheld Digital Manometer is Now Available {7490}

ELECTRONICS GP-ENGINE

Truck Engine News

Do Not Use the 261-3363 Wireless Communication Adapter with Model Year 2007 Cat Engines and Transmissions in On-Highway Trucks {0785, 1930, 7620}
2007/10/01

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 1900, 1901}
2014/04/04

Engine News

New Service Information Tool for CAT Dealers is Now Available {1000}
2002/06/01

277-4734 Bypass Harness Assembly Allows Cat Electronic Technician (Cat ET) to Communicate with ADEM IV:E2 Electronic Control Modules {0779, 0785, 1901, 1930}
2006/09/04

The Programmable Monitoring System Parameters Have New Descriptions {1901, 1902, 7620}
2007/10/22

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 1900, 1901}
2014/03/28

A New Electronic Control Module Wash Out Process {1901, 1920}
A New Electronic Control Module Wash Out Process {1901, 1920}

New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}

Special Instruction

"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}

Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}

Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}

Using the 217-0114 Adapter Cable As {0709, 1901, 1920}
Using the 217-0114 Adapter Cable As {0709, 1901, 1920}

Instructions for Communicating With and Flashing the 10R-4085 Engine Electronic Control Gp and the 10R-1824 Engine Electronic Control Gp {1901, 1920}
Instructions for Communicating With and Flashing the 10R-4085 Engine Electronic Control Gp and the 10R-1824 Engine Electronic Control Gp {1901, 1920}

Installation of Seat Belt Reminder Systems {1408, 1901, 1902, 7327, 7602, 7606, 7610, 7620}
Installation of Seat Belt Reminder Systems {1408, 1901, 1902, 7327, 7602, 7606, 7610, 7620}

Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ^® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}

Procedure to Flash the ADEM 3 Engine Electronic Control Gp {1901, 1920}
Procedure to Flash the ADEM 3 Engine Electronic Control Gp {1901, 1920}

Service Magazine

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel System{1278}
1985/11/25

New Oil Control Piston Ring Used In 3300 Family Of Engines {1213,1214,1215}
1990/03/26

Electronic Control Modules and Computer Viruses {7610}
2000/12/04

New Service Information Tool for CAT Dealers is Now Available {1900}
2002/06/17

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2012/04/17

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2013/07/11

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 7620}
2013/07/25

New Machine Software for Cat® Product Link Is Now Available on Certain Cat® Products {7490, 7606, 7610, 7620}
New Machine Software for Cat^® Product Link Is Now Available on Certain Cat^® Products {7490, 7606, 7610, 7620}

ELECTRONICS GP-POWER TRAIN

Engine News

The Programmable Monitoring System Parameters Have New Descriptions {1901, 1902, 7620}
2007/10/22

Special Instruction

Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}

Service Magazine

Electronic Control Modules and Computer Viruses {7610}
2000/12/04

277-2362 Transmission Analyzer III Group Offers Upgraded Diagnostic Capabilities {0769, 0779, 0783}
2007/10/22

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2012/04/17

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2013/07/11

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 7620}
2013/07/25

ELECTRONICS GP-IMPLEMENT

Special Instruction

Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}

Service Magazine

Electronic Control Modules and Computer Viruses {7610}
2000/12/04

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2012/04/17

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2013/07/11

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 7620}
2013/07/25

ELECTRONICS GP-MACHINE

Engine News

The Programmable Monitoring System Parameters Have New Descriptions {1901, 1902, 7620}
2007/10/22

New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}

Special Instruction

Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}

Installation of the Machine Security System (MSS) Universal Attachment Kit {7631, 7631}
Installation of the Machine Security System (MSS) Universal Attachment Kit {7631, 7631}

Tool Operating Manual

Communication Adapter II{0600, 0709, 7600, 7610}
Communication Adapter II{0600, 0709, 7600, 7610}

Service Magazine

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

Electronic Control Modules and Computer Viruses {7610}
2000/12/04

Parts Information for Locating Components of New Electronic Systems in SIS and Parts Manual {7602, 7631}
2001/04/09

New Firmware Is Now Available for Communications Adapter 3 {7610, 7620}
2011/10/20

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2012/04/17

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2013/07/11

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 7620}
2013/07/25

CONTROL GP-VOLTAGE

Special Instruction

Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}

Service Magazine

New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23

Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01

CONVERTER GP-ELECTRICAL

Catalytic Converter And Exhaust Conditioning Products Available{1091}
1995/01/16

COVER GP

Instrument Panel Guards Prevent Vandalism (Damage) To Machines{7315}
1982/09/20

ELECTRICAL GP

Special Instruction

Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}

Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}

Operation And Maintenance Of 1P3060 Pyrometer Group{0776}
Operation And Maintenance Of 1P3060 Pyrometer Group{0776}

Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}

Service Letter-NACD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Service Letter-China

Service Letter-Asia

Service Letter-APD

Service Magazine

Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28

Instrument Panel Guards Prevent Vandalism (Damage) To Machines{7315}
1982/09/20

Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29

Maintenance Free Batteries{1401}
1986/03/10

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01

Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10

Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15

Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11

12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors{1407}
1987/02/16

Polarity Connections And Use Of Service Meter Films When Service Meter Kits Are Installed{7480,7000}
1987/02/16

Check For Plugged Orifices In Mechanical Pressure Gauges{7450}
1987/03/02

Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Alternator "R" Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04

Testing The Starter On The Engine{1401,1450}
1987/05/04

Improved Start Switch Used{1416}
1987/05/25

Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25

Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

9G7641 Start Switch Is Improved{1416,1400}
1988/05/16

Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29

Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

More Potting Material Now Used In 6N5906 Electric Service Meter{7480}
1979/11/26

Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26

High Performance Maintenance Free Battery Available{1401}
1989/01/16

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

How To Troubleshoot A Short-To-Ground In Power Wiring{1400}
1989/03/27

Preventive Maintenance For Batteries{1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01

Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01

Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}
1989/06/19

Fitting Needed To Install New Oil Pressure Switch When Replacing Former Switches{7485}
1991/11/25

New PRELUB Systems Available For Medium To Large Caterpillar Construction Equipment {1319}
1992/04/06

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

Identification Of External Terminals On Alternators {1405,1406,1400}
1998/12/07

ELECTRONICS GP

Special Instruction

Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}

Cat® VIMS Converter Functionality {7610, 7620}
Cat^® VIMS Converter Functionality {7610, 7620}

2 Wire and 4 Wire Ethernet Repair Procedure on All Cat® Products {1408}
2 Wire and 4 Wire Ethernet Repair Procedure on All Cat^® Products {1408}

Installation Procedure to Retrofit a PL321VSR Electronic Control Module (ECM) With a Pro Product Link PL641 or PL631 or PL542 Systems {7606}
Installation Procedure to Retrofit a PL321VSR Electronic Control Module (ECM) With a Pro Product Link PL641 or PL631 or PL542 Systems {7606}

Installation Procedure to Retrofit a PL522 or PL523 With a Pro Product Link PL641 or PL631 or PL542 System {7606}
Installation Procedure to Retrofit a PL522 or PL523 With a Pro Product Link PL641 or PL631 or PL542 System {7606}

Service Magazine

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2012/04/17

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 7620}
2013/07/25

"Maintenance Mode" in Product Link is Used to Prevent Codes From Being Transmitted When Performing Service to a Machine or Engine {7606}
2014/11/24

Instructions for Preventing Utilization Messages Being Reported with Duplicate Time Stamps from PL321VSR Satellite Devices {7601}
2015/09/02

New Software Is Now Available for Cat® Product Link {7606, 7610, 7620}
New Software Is Now Available for Cat^® Product Link {7606, 7610, 7620}

A New Special Instruction for Installation Procedure to Retrofit a PL321VSR Electronic Control Module (ECM) With a Pro Product Link PL641 or PL631 or PL542 Systems is Now Available {7606}
A New Special Instruction for Installation Procedure to Retrofit a PL321VSR Electronic Control Module (ECM) With a Pro Product Link PL641 or PL631 or PL542 Systems is Now Available {7606}

A New Special Instruction for Installation Procedure to Retrofit a PL522 or PL523 With a Pro Product Link PL641 or PL631 or PL542 Systems is Now Available {7606}
A New Special Instruction for Installation Procedure to Retrofit a PL522 or PL523 With a Pro Product Link PL641 or PL631 or PL542 Systems is Now Available {7606}

Event Identification Number (EID) Above 60000 is Now Used on All Cat® Products {1400}
Event Identification Number (EID) Above 60000 is Now Used on All Cat^® Products {1400}

GLOW PLUG GP

Specifications

Glow Plug Positioning
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Disassembly and Assembly

Glow Plugs
3306 VEHICULAR ENGINE FOR D5B TRACTORS

Service Magazine

Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02

Shorter Mounting Bolts Used For Glow Plug Wiring{1403,1412}
1979/05/21

HANDLE AS-PROPEL

Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10

IGNITION GP

Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07

INDICATOR GP

Special Instruction

Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}

Service Magazine

Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11

Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27

Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03

New Engine Timing Indicator Group Available {0781,0782}
1986/07/07

Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16

INSTALLATION GP

Special Instruction

Installation of CAESultra for Track-Type Tractors{7010, 733T, 7490, 7604}
Installation of CAESultra for Track-Type Tractors{7010, 733T, 7490, 7604}

Service Magazine

Improved End - of - Line - Test Fixture for the Product Link Antenna is Now Used {7606}
2006/11/13

LIGHTING GP

Special Instruction

Current Draw Of Electric Starting Motors{1453}
Current Draw Of Electric Starting Motors{1453}

Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}

Installation Guide for the 35-Watt High Intensity Discharge (HID) Light{1429}
Installation Guide for the 35-Watt High Intensity Discharge (HID) Light{1429}

Disassembly and Assembly

Cab Light Assembly
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Service Magazine

Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28

Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29

Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16

Testing The Starter On The Engine{1401,1450}
1987/05/04

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

A New Halogen Lamp Is Now Available for Certain Cat Products {1434}
2011/06/29

MISCELLANEOUS INFORMATION

Special Instruction

Installation Of 9G4706 Ether Starting Aid Group For Direct Injection Engines{1456}
Installation Of 9G4706 Ether Starting Aid Group For Direct Injection Engines{1456}

Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}

Service Letter-NACD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Specifications

Alternator
DELCO REMY 20-SI SERIES ALTERNATOR

Service Letter-China

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Asia

Systems Operation

Systems Operation
DELCO REMY 20-SI SERIES ALTERNATOR

Service Letter-APD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Testing and Adjusting

Testing And Adjusting
DELCO REMY 20-SI SERIES ALTERNATOR

Disassembly and Assembly

Alternator
DELCO REMY 20-SI SERIES ALTERNATOR

Batteries
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Cab Liners, Disconnect Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Cab Light Assembly
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Back-Up Warning Alarm And Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Glow Plugs
3306 VEHICULAR ENGINE FOR D5B TRACTORS

Service Magazine

Use The 6V2056 Rod And 6V2057 Point To Find True Top Center{0653}
1980/07/14

New Horn Switch Available{7303}
1981/09/07

New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23

Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28

Instrument Panel Guards Prevent Vandalism (Damage) To Machines{7315}
1982/09/20

New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22

Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27

Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01

Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07

Maintenance Free Batteries{1401}
1986/03/10

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01

Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10

Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15

Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Identification Of External Terminals On Alternators{1405,1406,1400}
1987/03/23

Use Improved Heat Start Switch{1416}
1987/04/20

Products Equipped With Diagnostic Connectors Require Less Time For Electrical Troubleshooting{1400}
1987/05/04

Alternator "R" Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04

Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04

Testing The Starter On The Engine{1401,1450}
1987/05/04

Check Alternator Output Connection Prior To Machine Delivery{1405}
1987/05/18

Improved Start Switch Used{1416}
1987/05/25

Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25

Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23

9G7641 Start Switch Is Improved{1416,1400}
1988/05/16

Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

Shorter Mounting Bolts Used For Glow Plug Wiring{1403,1412}
1979/05/21

New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13

Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

High Performance Maintenance Free Battery Available{1401}
1989/01/16

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

How To Troubleshoot A Short-To-Ground In Power Wiring{1400}
1989/03/27

Preventive Maintenance For Batteries{1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01

Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}
1989/06/19

Fitting Needed To Install New Oil Pressure Switch When Replacing Former Switches{7485}
1991/11/25

Catalytic Converter And Exhaust Conditioning Products Available{1091}
1995/01/16

All-inclusive Electrical Schematic Listing{1400}
1995/03/27

MOTOR GP

Special Instruction

Current Draw Of Electric Starting Motors{1453}
Current Draw Of Electric Starting Motors{1453}

Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}

Service Magazine

Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28

Part Numbers for Electric Motors That Are Used in HVAC Have Changed {5927}
2000/10/30

An Improved Starting Motor is Now Available {1453}
2009/10/15

A New Starter Solenoid is Now Available {1467}
2008/03/17

PANEL GP-CIRCUIT BREAKER

Special Instruction

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

PANEL GP-FUSE

RECEPTACLE GP-AUXILIARY START

Service Magazine

Parts are Now Available to Make Jump Start Receptacle on Cat® Product {1463}
2014/03/04

REGULATOR GP-VOLTAGE

Special Instruction

Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}

Service Magazine

New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23

Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01

Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22

SENDER GP

Special Instruction

Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}

SENSOR GP

Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}

Tool Operating Manual

Using the 265-4177, 265-4209 Service Tool Groups to Install Sensors in Position-Sensing Hydraulic Cylinders{0599, 0709, 0738, 1439, 7562, 7562}
Using the 265-4177, 265-4209 Service Tool Groups to Install Sensors in Position-Sensing Hydraulic Cylinders{0599, 0709, 0738, 1439, 7562, 7562}

Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}

Reuse And Salvage Guidelines

Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736}
Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736}

Troubleshooting

MID 122 - CID 0269 - FMI 03
Product Link 121S/300

MID 122 - CID 0269 - FMI 04
Product Link 121S/300

Disassembly and Assembly

Coolant Temperature Sensor - Remove and Install
3304B and 3306B Engines for Caterpillar Built Machines

Engine Oil Pressure Sensor - Remove and Install
3304B and 3306B Engines for Caterpillar Built Machines

Service Magazine

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

Procedure Now Available to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
2012/10/04

SHUTOFF GP

Special Instruction

Installation of 5L8984, 3N584 and 8N1571 Solenoid Shutoff Groups{1259}
Installation of 5L8984, 3N584 and 8N1571 Solenoid Shutoff Groups{1259}

Specifications

Fuel Shutoff Solenoid
3306C Engines for Caterpillar Built Machines

Air Shutoff Solenoid
3306C Engines for Caterpillar Built Machines

Fuel Shutoff Solenoid
3306C Engines for Caterpillar Built Machines

Service Magazine

New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

New Fuel Shutoff Solenoids With Improved Durability Available {1259}
1999/03/22

SOLENOID GP

Special Instruction

Installation of 5L8984, 3N584 and 8N1571 Solenoid Shutoff Groups{1259}
Installation of 5L8984, 3N584 and 8N1571 Solenoid Shutoff Groups{1259}

Specifications

Starter Solenoids
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Fuel Shutoff Solenoid
3306C Engines for Caterpillar Built Machines

Service Magazine

Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors{1407}
1987/02/16

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

New Fuel Shutoff Solenoids With Improved Durability Available {1259}
1999/03/22

SOLENOID GP-SHUTOFF

Special Instruction

Installation of 5L8984, 3N584 and 8N1571 Solenoid Shutoff Groups{1259}
Installation of 5L8984, 3N584 and 8N1571 Solenoid Shutoff Groups{1259}

Disassembly and Assembly

Fuel Shutoff Solenoid - Remove and Install
3304B and 3306B Engines for Caterpillar Built Machines

Service Magazine

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

New Fuel Shutoff Solenoids With Improved Durability Available {1259}
1999/03/22

STARTING AID GP

Special Instruction

Installation Of 9G4706 Ether Starting Aid Group For Direct Injection Engines{1456}
Installation Of 9G4706 Ether Starting Aid Group For Direct Injection Engines{1456}

Specifications

Glow Plug Positioning
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Ether Starting Aid
3306C Engines for Caterpillar Built Machines

Disassembly and Assembly

Glow Plugs
3306 VEHICULAR ENGINE FOR D5B TRACTORS

Service Magazine

Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

Shorter Mounting Bolts Used For Glow Plug Wiring{1403,1412}
1979/05/21

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

A New Ether Cylinder O-ring is Now Used on All Caterpillar Products {1456}
2013/09/19

STARTING AR

Special Instruction

Current Draw Of Electric Starting Motors{1453}
Current Draw Of Electric Starting Motors{1453}

Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}

Service Magazine

Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16

Testing The Starter On The Engine{1401,1450}
1987/05/04

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24

STARTING MOTOR GP

Engine News

Caterpillar Remanufactured Electric Starting Motors Are Improved {1453}
2011/05/16

Special Instruction

Current Draw Of Electric Starting Motors{1453}
Current Draw Of Electric Starting Motors{1453}

Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}

Caterpillar PRELUB® Diagnostics{1469}
Caterpillar PRELUB^® Diagnostics{1469}

Starting Motor Solenoid - Replace {1467}
Starting Motor Solenoid - Replace {1467}

Installation of New Shift Lever Assembly for All Starter Motors {1453}
Installation of New Shift Lever Assembly for All Starter Motors {1453}

Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}

Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}

Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}

Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}

Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat^® Products {1408, 1450, 1453}

Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat^® Products {1408, 1450, 1453}

Procedure to Replace Drive Assembly of Starter Motor On All Cat® Products {1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat^® Products {1453}

Specifications

Starter Magnetic Switch
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Starter Motors
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Starter Solenoids
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Electric Starting Motor
3306C Engines for Caterpillar Built Machines

Testing and Adjusting

Electric Starting System - Test
3306C Engines for Caterpillar Built Machines

Pinion Clearance - Adjust
3306C Engines for Caterpillar Built Machines

Disassembly and Assembly

Starting Motor
3306 VEHICULAR ENGINE FOR D5B TRACTORS

Service Magazine

Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28

New Attachment Starting Motor Available{1453,1450}
1985/08/05

Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10

12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors{1407}
1987/02/16

Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16

Testing The Starter On The Engine{1401,1450}
1987/05/04

Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25

Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

New PRELUB Systems Available For Medium To Large Caterpillar Construction Equipment {1319}
1992/04/06

0R5207 Remanufactured Starter May Not Fit In Some Applications{1453}
1993/11/29

Examine Failed Starting Motors to Understand the Reason for Failure {1453}
2002/10/28

SWITCH GP

Special Instruction

Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}

Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}

Repair/Replacement Procedure for 5C-6108 Refueling Switch {1295}
Repair/Replacement Procedure for 5C-6108 Refueling Switch {1295}

Service Letter-NACD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Technical Information Bulletin

Machine Start Switch Key May Not Fit Properly{1416}
Machine Start Switch Key May Not Fit Properly{1416}

Specifications

Coolant Flow Switch
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Starter Magnetic Switch
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Service Letter-China

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Asia

Service Letter-APD

Disassembly and Assembly

Cab Liners, Disconnect Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Back-Up Warning Alarm And Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Service Magazine

New Horn Switch Available{7303}
1981/09/07

Maintenance Free Batteries{1401}
1986/03/10

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01

Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15

Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Use Improved Heat Start Switch{1416}
1987/04/20

Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04

Testing The Starter On The Engine{1401,1450}
1987/05/04

Improved Start Switch Used{1416}
1987/05/25

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

9G7641 Start Switch Is Improved{1416,1400}
1988/05/16

Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26

High Performance Maintenance Free Battery Available{1401}
1989/01/16

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

Preventive Maintenance For Batteries{1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01

Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01

Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}
1989/06/19

Fitting Needed To Install New Oil Pressure Switch When Replacing Former Switches{7485}
1991/11/25

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

Improved Prelube Pressure Switch Available {1400,1435,1319}
1995/09/11

Improved Procedure for Verifying the Operation of the Battery Disconnect System. {1411}
2009/05/04

New Pressure Switch Is Now Used For Air Conditioner Refrigerant On Certain Cat Products {1435, 1809}
2011/06/06

An Improved 5P-8500 Key Is Now Available {1416, 1416, 7000, 7000}
2011/12/01

TOOLS

Truck Engine News

Coolant/Battery Tester Group Quickly Tests Coolant and Battery Acid {0773, 0785}
2004/12/27

Do Not Use the 261-3363 Wireless Communication Adapter with Model Year 2007 Cat Engines and Transmissions in On-Highway Trucks {0785, 1930, 7620}
2007/10/01

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 1900, 1901}
2014/04/04

Engine News

Caterpillar Electronic Technician (Cat ET) 2001B-Service Pack 1 Software Upgrade is Now Available {0785}
2002/02/01

2002A Service Pack 1 for Caterpillar Electronic Technician (Cat ET) is now available {0785}
2002/08/01

The 237-5130 Digital Multimeter Gp Features a Built-in Infrared Thermometer {0785}
2004/04/19

Coolant/Battery Tester Group Quickly Tests Coolant and Battery Acid {0773, 0785}
2004/12/27

260-5800 Electrical Test Group Packages Digital Multimeter, Clamp-on Ammeter, Current Detector, and Test Leads in Convenient Carrying Case {0785}
2005/03/07

270-5051 Repair Kit (Electrical Connectors) Available for Repairs to Wiring Harnesses with Ampseal 16 and A4E 2 Connectors {0709, 1408}
2006/03/20

Enhanced Voltmeter Leads Are Now Available {0785}
2006/02/13

Test Cable Group Checks Three-Wire, Active Analog Circuits That Are Used in Sensors {0779, 0785}
2006/10/16

277-4734 Bypass Harness Assembly Allows Cat Electronic Technician (Cat ET) to Communicate with ADEM IV:E2 Electronic Control Modules {0779, 0785, 1901, 1930}
2006/09/04

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 1900, 1901}
2014/03/28

Special Instruction

Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}

Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}

Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}

Procedure to Access the License Information for Caterpillar Electronic Technician (CAT ET){0785}
Procedure to Access the License Information for Caterpillar Electronic Technician (CAT ET){0785}

An Aid To Reading Multimeter Scales{0785}
An Aid To Reading Multimeter Scales{0785}

Tool Operating Manual

348-5430 Multi-Tool Gp 2 {0709, 0769, 0785}
348-5430 Multi-Tool Gp 2 {0709, 0769, 0785}

NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}

Using the Communications Adapter 3{1900}
Using the Communications Adapter 3{1900}

Using the 8T-2700 Blowby/Air Flow Indicator{0781, 0785, 1317}
Using the 8T-2700 Blowby/Air Flow Indicator{0781, 0785, 1317}

146-4080 Digital Multimeter Specification, Testing, and Maintenance Manual{0374, 0599, 0709}
146-4080 Digital Multimeter Specification, Testing, and Maintenance Manual{0374, 0599, 0709}

Communication Adapter II{0600, 0709, 7600, 7610}
Communication Adapter II{0600, 0709, 7600, 7610}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}

131-5051 Dataview Group and Dataview Portable Tech Station Group{0374, 0599, 0701, 0709}
131-5051 Dataview Group and Dataview Portable Tech Station Group{0374, 0599, 0701, 0709}

Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}
Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}

NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}

M0090131 Battery Analyzer 480-4181 (484-4859 Group) {0374, 0599, 0709, 1401, 7468}
M0090131 Battery Analyzer 480-4181 (484-4859 Group) {0374, 0599, 0709, 1401, 7468}

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Troubleshooting

Service Tools
Product Link - PL522/523

Service Tools
Product Link 121S/300

Service Magazine

New Address For Repair Of Diagnostic Tools{0650}
1982/06/14

6V6124 Calibration Coil Available To Calibrate And Check 6V4910 AC/DC Clamp-On Ammeter{0651}
1982/06/28

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16

Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27

Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Two New Self-Powered Digital Tachometers And Signal Generator Available {7462}
1987/05/11

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Diagnostic Cables and Harnesses Are Available {0785}
2014/08/11

Caterpillar Electronic Technician (Cat ET) 2001B-Service Pack 1 Software Upgrade is Now Available {0785}
2002/02/11

New Service Information Tool for CAT Dealers is Now Available {1900}
2002/06/17

2002A Service Pack 1 for Caterpillar Electronic Technician (Cat ET) is Now Available {0785}
2002/08/19

USB Cable Connects PC with USB Ports to Communication Adapter or to DataView Tool Group {0785, 0788}
2004/03/15

Coolant/Battery Tester Group Quickly Tests Coolant and Battery Acid {0773, 0785}
2004/12/27

260-5800 Electrical Test Group Packages Digital Multimeter, Clamp-on Ammeter, Current Detector, and Test Leads in Convenient Carrying Case {0785}
2005/03/07

The 285-0910 Multi-Tool Gp Incorporates Four Diagnostic Tools into a Single, Hand Held Unit {0774, 0779, 0781, 0782}
2006/11/27

New 271-8590 Analyzer Gp (24-Volt) Quickly Identifies Starting and Charging System Problems {0709, 1406}
2006/10/02

277-2362 Transmission Analyzer III Group Offers Upgraded Diagnostic Capabilities {0769, 0779, 0783}
2007/10/22

Updated Instruction For The Bypass Harness {0785, 1408}
2008/03/17

New Firmware Is Now Available for Communications Adapter 3 {7610, 7620}
2011/10/20

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 7620}
2013/07/25

New Software For Cat® ET Can Now Be Used For All Caterpillar Products {0785, 7606}
2013/08/15

A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}
2014/10/07

Comprehensive List of Electrical Repair and Troubleshooting Information Is Now Available for All CAT Machines {0374, 0709, 1400, 1408, 7490, 7553, 7610}
Comprehensive List of Electrical Repair and Troubleshooting Information Is Now Available for All CAT Machines {0374, 0709, 1400, 1408, 7490, 7553, 7610}

VALVE GP

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23

WARNING GP

Special Instruction

Installation of 244-1090 Alarm Gp {7400, 7402, 7407}
Installation of 244-1090 Alarm Gp {7400, 7402, 7407}

Disassembly and Assembly

Back-Up Warning Alarm And Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Service Magazine

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

WIRING GP

Engine News

Correction to The Pocket Guide, SEBD0402 Is Available as a Reference for Routing and Installing Wire Harness Assemblies {1408}
2000/07/01

270-5051 Repair Kit (Electrical Connectors) Available for Repairs to Wiring Harnesses with Ampseal 16 and A4E 2 Connectors {0709, 1408}
2006/03/20

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/13

Special Instruction

Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}

Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}

Installation Of 9G3 And 9G4 Battery Terminal Covers{1401}
Installation Of 9G3 And 9G4 Battery Terminal Covers{1401}

Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}

Cross-Reference for Electrical Connectors {7553}
Cross-Reference for Electrical Connectors {7553}

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

Ampseal 16 Connector Peripheral Seal Servicing{7553}
Ampseal 16 Connector Peripheral Seal Servicing{7553}

Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}
Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}

Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}
Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}

Repair Procedure for Damaged Harness Wiring {1408}
Repair Procedure for Damaged Harness Wiring {1408}

Installation Procedure for Product Link PL421 Retrofit{7606}
Installation Procedure for Product Link PL421 Retrofit{7606}

Installation of Seat Belt Reminder Systems {1408, 1901, 1902, 7327, 7602, 7606, 7610, 7620}
Installation of Seat Belt Reminder Systems {1408, 1901, 1902, 7327, 7602, 7606, 7610, 7620}

DRCP Connector Repair Service Instruction {1408, 7553}
DRCP Connector Repair Service Instruction {1408, 7553}

Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}

Service Letter-NACD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Specifications

Coolant Flow Switch
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Starter Magnetic Switch
3306 VEHICULAR ENGINE FOR D5B, D6D & D7G TRACTORS

Tool Operating Manual

Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}
Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}

Service Letter-China

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Asia

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Service Letter-APD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Testing and Adjusting

Electric Starting System - Test
3306C Engines for Caterpillar Built Machines

Electrical Connector - Inspect
Product Link - PL522/523

Wiring Harness (Open Circuit) - Test
Product Link - PL522/523

Wiring Harness (Short Circuit) - Test
Product Link - PL522/523

Electrical Connector - Inspect
Product Link 121S/300

Wiring Harness (Open Circuit) - Test
Product Link 121S/300

Wiring Harness (Short Circuit) - Test
Product Link 121S/300

Troubleshooting

MID 122 - CID 0269 - FMI 03
Product Link 121S/300

MID 122 - CID 0269 - FMI 04
Product Link 121S/300

Disassembly and Assembly

Batteries
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Cab Liners, Disconnect Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Back-Up Warning Alarm And Switch
D4E, D5B & D6D TRACTORS OPERATOR'S STATION

Glow Plugs
3306 VEHICULAR ENGINE FOR D5B TRACTORS

Service Magazine

New Horn Switch Available{7303}
1981/09/07

Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29

Maintenance Free Batteries{1401}
1986/03/10

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02

Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01

Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Alternator "R" Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04

Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04

Testing The Starter On The Engine{1401,1450}
1987/05/04

Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14

Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29

Shorter Mounting Bolts Used For Glow Plug Wiring{1403,1412}
1979/05/21

Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26

High Performance Maintenance Free Battery Available{1401}
1989/01/16

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

How To Troubleshoot A Short-To-Ground In Power Wiring{1400}
1989/03/27

Preventive Maintenance For Batteries{1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01

Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01

Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}
1989/06/19

Fitting Needed To Install New Oil Pressure Switch When Replacing Former Switches{7485}
1991/11/25

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

Parts Manuals May List Air Conditioning Compressors Incorrectly {1802,1809,7320}
1996/10/07

Special Instruction, REHS0440 is Available for an Index of Electrical System Schematics {7566}
2000/04/10

Correction to The Pocket Guide, SEBD0402, Is Available as a Reference for Routing and Installing Wire Harness Assemblies {1408}
2000/06/26

Harness Repair of Alternator R-Terminal Connector {1405, 1408, 7553}
2000/10/02

Dielectric Grease Should Not Be Used in Electrical Connectors {1408, 7553}
2012/05/04

Service of the Machined Terminals and the Stamped and Formed Terminals {7553}
2006/11/13

Updated Instruction For The Bypass Harness {0785, 1408}
2008/03/17

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/12

Striped Wire Is Replaced With Improved Ink Jet Identification for Legacy (Parts Service) Wire harnesses {1408}
2012/06/08

Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}
2012/05/08

Information On Battery Cables and Wire Assemblies for Assembling at Dealer Site {4459}
2012/09/21

Parts are Now Available to Make Jump Start Receptacle on Cat® Product {1463}
2014/03/04

CONNECTION GP

Tool Operating Manual

Service Magazine

Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553}
Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553}

RELAY GP

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

ELECTRONICS GP-MONITOR

Engine News

New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}

Special Instruction

Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}

Diesel Particulate Filter Monitoring System {108F, 7490}
Diesel Particulate Filter Monitoring System {108F, 7490}

Installation of Cat® Terrain v4.5 for Track-Type Tractors {7605}
Installation of Cat^® Terrain v4.5 for Track-Type Tractors {7605}

Installation of G610 Hardware for Cat® Terrain for Track-Type Tractors {7605}
Installation of G610 Hardware for Cat^® Terrain for Track-Type Tractors {7605}

Installation Of Operator ID System on Cat® and Non-Cat Products {7600, 7610, 7620}
Installation Of Operator ID System on Cat^® and Non-Cat Products {7600, 7610, 7620}

Cat® VIMS Converter Functionality {7610, 7620}
Cat^® VIMS Converter Functionality {7610, 7620}

Technical Information Bulletin

Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}
Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}

Tool Operating Manual

Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}
Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}

Service Magazine

Electronic Control Modules and Computer Viruses {7610}
2000/12/04

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2012/04/17

Improved VisionLinkTM Software Is Now Available for Certain Caterpillar Machines {7601}
2012/06/07

New Software Is Now Available for Cat® Product Link 522 Systems {7494, 7606, 7620}
2012/12/10

Procedure For Improving Compatibility of Product Link Is Now Available on Caterpillar Machines Equipped with Electronic Monitoring Systems (EMS) {7490, 7606}
2013/04/04

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2013/07/11

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 7620}
2013/07/25

New Inspection and Repair Procedure Is Now Available for Cat® Products Located in India Equipped with Product Link {7606}
2014/09/22

New Phone Number for VIMS Support Is Now Available for All Cat® Products Equipped with VIMS {7601}
2015/03/02

New Software Is Now Available for All Cat® Products With PL522 China System {7606, 7620}
2015/03/04

New Troubleshooting Procedure Is Now Available for all Cat® Products Equipped with PL321 VIMS (PL321 VSR) {7606}
2015/05/12

New Software Is Now Available for Cat® Product Link {7606, 7610, 7620}
New Software Is Now Available for Cat^® Product Link {7606, 7610, 7620}

A New Handheld Digital Manometer is Now Available {7490}
A New Handheld Digital Manometer is Now Available {7490}

HEATER GP

Special Instruction

Installation Of 1N4440, 8N9527, 8N9751 Or 8N9752 Fuel Heater Groups{1296}
Installation Of 1N4440, 8N9527, 8N9751 Or 8N9752 Fuel Heater Groups{1296}

Service Magazine

How To Identify Failures To Electric Jacket Water Heaters{1383}
1988/04/18

New Bracket Available For Installation Of Jacket Water Heater{1383}
1979/09/17

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

ELECTRONICS GP-WORK TOOL

Special Instruction

Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}

Service Magazine

Electronic Control Modules and Computer Viruses {7610}
2000/12/04

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2012/04/17

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2013/07/11

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 7620}
2013/07/25

ELECTRONICS GP-COMMUNICATION

Operation and Maintenance Manual

Product Link
Product Link - PL121, PL321, PL522, and PL523

General Hazard Information
Product Link - PL121, PL321, PL522, and PL523

Safety Signs and Labels
Product Link - PL121, PL321, PL522, and PL523

Special Instruction

Installation Instructions For Product Link 101 Inline Timer{7602}
Installation Instructions For Product Link 101 Inline Timer{7602}

Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}

Product Link MODEM Programming with Cat Electronic Technician (ET){7606, 7620}
Product Link MODEM Programming with Cat Electronic Technician (ET){7606, 7620}

Product Link PL-102C System Installation{7606}
Product Link PL-102C System Installation{7606}

Product Link PL-102C{7602}
Product Link PL-102C{7602}

Installation Guide for Product Link PL121SR and PL321{7606}
Installation Guide for Product Link PL121SR and PL321{7606}

Operation of Product Link{7606}
Operation of Product Link{7606}

Product Link PL121SR{7606}
Product Link PL121SR{7606}

Installation Procedure for Product Link PL522 and PL523 (Cellular) {7606}
Installation Procedure for Product Link PL522 and PL523 (Cellular) {7606}

Installation Procedure for Product Link PL421 Retrofit{7606}
Installation Procedure for Product Link PL421 Retrofit{7606}

Release Notes for VisionLink and VisionLink Store for All Caterpillar Products {7606, 7620}
Release Notes for VisionLink and VisionLink Store for All Caterpillar Products {7606, 7620}

Installation of Seat Belt Reminder Systems {1408, 1901, 1902, 7327, 7602, 7606, 7610, 7620}
Installation of Seat Belt Reminder Systems {1408, 1901, 1902, 7327, 7602, 7606, 7610, 7620}

Product LinkTM PL421 Installation Quick Reference Guide{7606}
Product Link^TM PL421 Installation Quick Reference Guide{7606}

Technical Information Bulletin

Miswiring Issues with Installation of the Product Link 121 and Product Link 321{7606}
Miswiring Issues with Installation of the Product Link 121 and Product Link 321{7606}

Product Link Antenna Placement{7606}
Product Link Antenna Placement{7606}

Product Link Hours Versus Service Meter Hours Accuracy Issue{7606}
Product Link Hours Versus Service Meter Hours Accuracy Issue{7606}

Product Link Registration Problems{733T, 7606}
Product Link Registration Problems{733T, 7606}

Multiple Registration Messages Occur with Product Link{733T, 7606}
Multiple Registration Messages Occur with Product Link{733T, 7606}

Product Link PL321 May Accumulate 24 Hours Daily{7606}
Product Link PL321 May Accumulate 24 Hours Daily{7606}

Registration of Product Link in EquipmentManager{7606}
Registration of Product Link in EquipmentManager{7606}

Location Updates Are Not Being Reported From The Product Link PL321{7606}
Location Updates Are Not Being Reported From The Product Link PL321{7606}

Updating to Latest VIMS3G Flash Files And Configuration Files Available For Cat® Machines Equipped With VIMS3G{7601, 7620}
Updating to Latest VIMS3G Flash Files And Configuration Files Available For Cat^® Machines Equipped With VIMS3G{7601, 7620}

Improper Customer Access and Asset Merging Within VisionLinkTM and PartStoreTM Through UCID Consolidation{7567, 7606}
Improper Customer Access and Asset Merging Within VisionLink^TM and PartStore^TM Through UCID Consolidation{7567, 7606}

Tool Operating Manual

Communication Adapter II{0600, 0709, 7600, 7610}
Communication Adapter II{0600, 0709, 7600, 7610}

Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}
Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}

Systems Operation

System Overview
Product Link 121S/300

Manage Hardware
EquipmentManager User Guide

Manage Time Fence and Geographic Fence
EquipmentManager User Guide

Manage Planned Maintenance
EquipmentManager User Guide

Time Fence and Geographic Fence
EquipmentManager Dealer Administrator Manual

Health Watch
EquipmentManager User Guide

Product Monitoring
EquipmentManager User Guide

Operation and Maintenance Manual
EquipmentManager User Guide

Equipment Usage
EquipmentManager Dealer Administrator Manual

Verify Machine Records and Ownership
EquipmentManager User Guide

Manage Equipment Groups
EquipmentManager User Guide

Fuel Results
EquipmentManager User Guide

Planned Maintenance
EquipmentManager User Guide

General Information
EquipmentManager Dealer Administrator Manual

Getting Started
EquipmentManager Dealer Administrator Manual

Enable Program
EquipmentManager Dealer Administrator Manual

Manage Users
EquipmentManager User Guide

Product Link Installation
EquipmentManager Dealer Administrator Manual

Setup Subscriptions
EquipmentManager Dealer Administrator Manual

Administration
EquipmentManager Dealer Administrator Manual

Manage Equipment Groups
EquipmentManager Dealer Administrator Manual

Manage Event Tracking
EquipmentManager User Guide

Upload Data
EquipmentManager User Guide

Manage Planned Maintenance
EquipmentManager Dealer Administrator Manual

Preferences
EquipmentManager User Guide

Asset Watch
EquipmentManager Dealer Administrator Manual

Maintenance Watch
EquipmentManager Dealer Administrator Manual

Major Repair
EquipmentManager Dealer Administrator Manual

Fault Codes
EquipmentManager Dealer Administrator Manual

Preference Detail
EquipmentManager Dealer Administrator Manual

Reports
EquipmentManager Dealer Administrator Manual

Active Fleet
EquipmentManager Dealer Administrator Manual

Product Usage
EquipmentManager User Guide

Verify Machine Records and Ownership
EquipmentManager Dealer Administrator Manual

Manage Major Repair Tracking
EquipmentManager Dealer Administrator Manual

System Overview
Product Link - PL522/523

System Components
Product Link - PL522/523

Configuration
Product Link - PL522/523

Installation Parameters Configure
Product Link - PL522/523

Spare Input Configure
Product Link - PL522/523

Commands
Product Link - PL522/523

System Components
Product Link 121S/300

Spare Inputs
Product Link 121S/300

Configuration
Product Link 121S/300

Testing and Adjusting

Electronic Control Module (ECM) - Flash Program
Product Link - PL522/523

Electronic Control Module (ECM) - Replace
Product Link - PL522/523

Specifications
Product Link - PL522/523

Troubleshooting

General Information
Product Link - PL522/523

Diagnostic Capabilities
Product Link - PL522/523

Electronic Service Tool Does Not Communicate with ECM
Product Link - PL522/523

Reports and Messages Not Available
Product Link - PL522/523

Position Reports Not Available
Product Link - PL522/523

Reporting Interval Erratic
Product Link - PL522/523

Diagnostics and Events Not Available
Product Link - PL522/523

Operating Hours Discrepancy
Product Link - PL522/523

Diagnostic Code List
Product Link - PL522/523

MID 161 - CID 0254 - FMI 04
Product Link - PL522/523

MID 161 - CID 0254 - FMI 12
Product Link - PL522/523

MID 161 - CID 1250 - FMI 09
Product Link - PL522/523

MID 161 - CID 1888 - FMI 14
Product Link - PL522/523

MID 161 - CID 3766- FMI 14
Product Link - PL522/523

Service Magazine

Electronic Control Modules and Computer Viruses {7610}
2000/12/04

Parts Information for Locating Components of New Electronic Systems in SIS and Parts Manual {7602, 7631}
2001/04/09

New Version of Product Link Available {7602}
2001/08/27

New Flash File Software Is Used for Product Link 151/201 {7606, 7620}
2002/07/15

New Flexible Antenna Whip Available for Product Link {7606}
2002/12/02

New Flash File Software Is Used for Product Link 151/201 {7620}
2003/03/10

New Software Is Used on Product Link 151/201 {7606, 7620}
2003/09/01

Product Link Cellular Is Now Available {7602}
2004/08/02

Correction to Special Instruction, REHS2143, "Product Link PL-102C System Installation" {7602}
2004/08/02

Correction to Special Instruction, "Product Link PL102C System Installation" and Systems Operation, Testing and Adjust, "Product Link PL102C" {7602}
2004/12/13

New PC Service Tool Software Released for Cellular Based Product Link {7620}
2004/12/20

Correction to Special Instruction, "Product Link PL102C System Installation" {7620}
2004/12/13

Procedure to Identify which COM PORT the USB Device Is Occupying and the Procedure to Change the Default COM PORT Setting {7606}
2005/01/10

New Product Link Software Available for PL151 and PL201 {7606}
2005/01/10

New Product Link Systems Are Now Available {7606}
2005/02/07

New Software Available for Product Link PL-151 and PL-201 {7620}
2005/05/02

New Product Link Software Is Now Available {7606, 7620}
2005/12/19

New Software Available for Product Link {7606, 7620}
2006/10/16

New Product Link Software Is Now Available {7606, 7620}
2007/05/14

New Product Link Hardware Is Now Available {7606}
2008/03/17

New Processes Improve Registration of Product Link {7338, 7606}
2008/04/14

New Software for Product Link is Now Available {7606, 7620}
2008/03/10

New Software for Product Link is Now Available {7606, 7620}
2008/05/19

New Software is Now Used for the Product Link PL121SR and PL321SR Systems {7606, 7620}
2009/10/15

New Product Link Cellular Is Released for All Cat Products {7606}
2011/03/04

New Software Is Now Released for Product Link PL522/523 Systems On All Cat Product {7606}
2011/05/12

A New Product Link Registration/Activation Process Now Available For Product Link (PL) 522 and 523 {7606}
2011/10/19

New Software for Product Link (PL300) Is Now Available {7606, 7620}
2011/10/11

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2012/04/17

New Software Is Now Available for Product Link (PL 121) {7602, 7610, 7620}
2011/12/15

New Software Is Now Available for Cat® Product Link 522 Systems {7494, 7606, 7620}
2012/12/10

Improved Process for Activating Product Link PL522 On Assets In China {7606}
2012/11/19

Improved VisionLink And VisionLink Store Software Are Now Available for All Caterpillar Products {7606, 7620}
2015/07/14

New Software Is Now Available For Product Link 522 Systems On All Cat® Products {7606, 7620}
2013/05/28

Procedure For Improving Compatibility of Product Link Is Now Available on Caterpillar Machines Equipped with Electronic Monitoring Systems (EMS) {7490, 7606}
2013/04/04

Improved VisionLinkTMStore is Now Available for all Caterpillar Products {7606}
2013/03/29

Device Transfers Are Now Supported In VisionLinkTM Store {7606}
2013/03/29

Improved VisionLinkTM Store for Minimizing Delay in Appearance of VisionLink Store - Modules is Now Available for All Caterpillar Products {7606}
2013/03/29

New Product Link Software for PL121 and PL300 Is Now Available for All Cat® Products {7606, 7610, 7620}
2013/05/02

New Software Is Now Available for All Cat® Products With The Product Link 522 System {7606}
2013/09/27

New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
2013/07/08

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2013/07/11

New Software Flash File Extension Requires Caterpillar Electronic Technician (Cat ET) 2013B {0785, 7620}
2013/07/25

New Software For Cat® ET Can Now Be Used For All Caterpillar Products {0785, 7606}
2013/08/15

New Software Is Now Available For All Cat® Products With PL522 China System {7606, 7620}
2013/08/19

Procedure for Improving Antenna Communication on All Machines Equipped With Product Link {733B, 7606}
2013/09/16

Improvements for Products and Systems Connected to Product Link {7606}
2013/10/02

New Product Link Software for PL300 Is Now Available for All Cat ®Products {7606, 7620}
2013/10/21

New Software Is Now Available for All Cat® Products With The Product Link PL421 or Product Link PL420 System {7606, 7620}
2013/10/02

Improved Product Link Satellite System Special Instruction guide {7606}
2013/12/20

Truck sale:

22,773

Caterpillar D5B, Construction
- Dozers
BERGERAT MONNOYEUR S.A.S.
France

CATERPILLAR D5B 1984
- TRACK TYPE TRACTORS
BERGERAT MONNOYEUR
117 RUE CHARLES MICHELS - ST DENIS -

CATERPILLAR D5B 1978
- TRACK TYPE TRACTORS
BERGERAT MONNOYEUR
117 RUE CHARLES MICHELS - ST DENIS -

Call

1982 CAT D5B

C&C Machinery LLC

USD $25,500

CAT D5B

Riggs Tractor Company & Dozer Service
Severy, Kansas