AVSPARE.COM
parts catalog

HOLD DOWN B126496 - Caterpillar



B126496 HOLD DOWN Caterpillar parts CB-514 HOLD
Rating:
66
Alternative (cross code) number:
CAB126496
B12-6496
B126496
Caterpillar B126496 HOLD DOWN

Buy HOLD DOWN B126496 Caterpillar genuine, new aftermarket tractor parts with delivery
VIBRATORY COMPACTOR,

Compatible equipment models: B126496:

VIBRATORY COMPACTOR  CB-514   Caterpillar
Number on catalog scheme: 12
 
  For full view, you need register

Information:


Illustration 1 g00933360
Remove pin (1) that holds cylinder rod (2) to bracket (3) .
Retract cylinder rod (2) into the cylinder as far as possible. Stop the engine.
Illustration 2 g00933362
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Machine Preparation for Disassembly and Assembly".
Illustration 3 g00932648
Attach Tooling (A) to the hydraulic oil tank, as shown. Apply 276 kPa (40 psi) to 414 kPa (60 psi).
Disconnect hose assemblies (4) and (5) .
Illustration 4 g00933363
Remove nut (6), the washer, and bolt (7) .
Remove pin (8) .
Illustration 5 g00933364
Attach a suitable lifting device to sideshift cylinder (9). The weight of sideshift cylinder (9) is approximately 113 kg (250 lb). Slide sideshift cylinder (9) to the right and remove sideshift cylinder (9) .
Remove cylinder (9) .Disassembly and Assembly Information
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     127-4904     Hydraulic Cylinder Repair Stand     1    
B     7M-7456     Bearing Mount Compound     1    
C     1P-0808     Multipurpose Grease     1    
D     195-4609     Seal Pick     1    
E     9U-7868     Spanner Wrench     1    
127-8064 Adjustable Plate     1    
Illustration 6 g00933497
(1) Apply Tooling (B) to the seal groove prior to assembling the wiper seal. (2) Lubricate sealing lips with a thin covering of the lubricant that is being sealed. (3) Torque for head ... 600 130 N m (440 95 lb ft) (4) Use a 46 mm socket to remove the bolt.Note: Apply Tooling (C) to the threads.Installation Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Illustration 7 g00933364
Attach a suitable lifting device to sideshift cylinder (9). The weight of sideshift cylinder (9) is approximately 113 kg (250 lb). Position sideshift cylinder (9) on the machine.
Illustration 8 g00933363
Install pin (8) .
Install bolt (7), the washer, and nut (6) .
Illustration 9 g00933362
Connect hose assemblies (5) and (4) .
Illustration 10 g00933360
Start the engine. Extend the cylinder rod out of the cylinder as far as needed for alignment.
Install pin (1) that holds rod (2) to bracket (3) .

Caterpillar parts catalog:

Caterpillar parts catalog
CB-514 VIBRATORY COMPACTOR 6YD00001-UP (MACHINE) POWERED BY 3.53 ENGINE


Parts hold Caterpillar catalog:

0774065 HOLD-DOWN
AP-200, CB-314, CP-433B, CS-323, CS-431B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.