AVSPARE.COM
parts catalog

HOOD AS 3977512 - Caterpillar


3977512 HOOD AS Caterpillar parts
Rating:
61
Alternative (cross code) number:
CA3977512
397-7512
3977512
Caterpillar 3977512 HOOD AS
Weight: 25 pounds 11 kg.

Buy HOOD AS 3977512 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 10
  For full view, you need register

Information:


Illustration 1 g02160341
Schematic of the Cat Data Link CircuitThis diagnostic code is recorded when the Machine ECM does not receive the expected information from the Monitoring System ECM.Note: The Machine ECM is located inside the Center Console.The likely possible causes of this diagnostic code are listed below:
The software that is installed on the Monitoring System ECM is incorrect.
The software that is installed on the Machine ECM is incorrect.System Response:Select display features may not function properly.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS.
Verify that the following information is correct:
The part number of the software of the Machine ECM
The part number of the Monitoring System ECM software
The part number of the Machine ECM
The part number of the Monitoring System ECM Note: Consult the Business Unit that produces the product for the correct part numbers of the configuration software. Expected Result:All part numbers are correct. Results:
OK - All part numbers are correct. Proceed to test step 2.
NOT OK - All part numbers are NOT correct. The part number of the Machine ECM may be incorrect. The part number of the Monitoring System ECM may be incorrect. The incorrect configuration software may also be installed. Repair: Replace the incorrect ECM with an ECM that has the correct part number. Flash the correct configuration software. See Troubleshooting, "Electronic Control Module - Flash Program".STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect all harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the connectors for proper mating.
Check the wires at the connector.
Check each wire for nicks or signs of abrasion in the insulation.
Check for moisture at the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and check each socket of the machine harness connectors. Expected Result:The machine harness connectors are tight and free of corrosion. Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to test step 3.
NOT OK - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK FOR SHORTS TO GROUND.
The disconnect switch remains in the OFF position.
Disconnect the machine harness from all electronic control modules that use the Cat Data Link.
At the machine harness for the Machine ECM, measure the resistance between frame ground and connector contacts J1-10 (wire 944-OR) and J1-20 (wire 945-BR) of the Cat Data Link circuit. Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to test step 4.
NOT OK - The resistance is less than 5000 ohms. The machine harness has failed. Repair: There is a short between frame ground and the Cat Data Link circuit in the machine harness. Repair the machine harness or replace the machine harness. STOPTest Step 4. CHECK FOR A SHORT TO THE +BATTERY CIRCUIT.
The disconnect switch remains in the OFF position.
All related electronic control modules remain disconnected

Caterpillar parts catalog:

Caterpillar parts catalog
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4.4 Engine
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4.4 Engine
420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY C4.4 Engine
430F2 Center Pivot Backhoe Loader LYD00001-UP (MACHINE) POWERED BY C4.4 Engine
430F2 IT Center Pivot Backhoe Loader LYE00001-UP (MACHINE) POWERED BY C4.4 Engine
422F2 Side Shift Backhoe Loader LYF00001-UP (MACHINE) POWERED BY C4.4 Engine
428F2 Side Shift Backhoe Loader LYG00001-UP (MACHINE) POWERED BY C4.4 Engine
432F2 Side Shift Backhoe Loader LYJ00001-UP (MACHINE) POWERED BY C4.4 Engine
434F2 Side Shift Backhoe Loader LYK00001-UP (MACHINE) POWERED BY C4.4 Engine
444F2 Side Shift Backhoe Loader LYL00001-UP (MACHINE) POWERED BY C4.4 Engine
415F2 Center Pivot Backhoe Loader HWA00001-UP (MACHINE) POWERED BY C3.4 Engine
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4 Engine
415F2 IL Backhoe Loader PF400001-UP (MACHINE) POWERED BY C3.4 Engine


Parts hood Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.