HOOK 3291327 - Caterpillar

Table 2
Linkage Bearings and Seals    
View     Bearing     Part Number of Bearing     Inside Diameter of Bearing     Bearing Depth at Assembly     Seal     Part Number of Seal    
A-A     3     4E-5582    
160.220 0.025 mm (6.3079 0.0010 inch)    
10 0.5 mm (0.39 0.020 inch)     2     9X-7700    
B-B     5     194-1664    
140.35 0.025 mm (5.5256 0.0010 inch)    
11.5 0.5 mm (0.45 0.020 inch)     6     197-3919    
C-C     10     132-7431    
150.350 0.025 mm (5.9193 0.0010 inch)    
9.5 1.0 mm (0.37 0.040 inch)     11     9X-7699    
D-D     13     132-7431    
150.350 0.025 mm (5.9193 0.0010 inch)    
9.5 1.0 mm (0.37 0.040 inch)     18     9X-7699    
E-E     14     6E-1166    
160.210 0.025 mm (6.3075 0.0010 inch)    
10 0.5 mm (0.39 0.020 inch)     19     9X-7700    
F-F     17     4E-5588    
220.310 0.025 mm (8.6736 0.0010 inch)    
11.5 0.5 mm (0.45 0.020 inch)     20     9X-7703    
G-G     22     6E-1166    
160.210 0.025 mm (6.3075 0.0010 inch)    
10 0.5 mm (0.39 0.020 inch)     28     9X-7700    
H-H     24     6E-1166    
160.210 0.025 mm (6.3075 0.0010 inch)    
10 0.5 mm (0.39 0.020 inch)     29     9X-7700    
K-K     26     6E-1164    
160.210 0.025 mm (6.3075 0.0010 inch)    
10 0.5 mm (0.39 0.020 inch)     31     9X-7700     (7) The thickness of the 209-7224 Shim ... 1 mm (0.04 inch) (8) The thickness of the 209-7225 Shim ... 2 mm (0.08 inch)Note: At assembly of the B-pin Joint, stack the shims between the bucket hinge and the lift arm. Stack the proper amount of shims in order to reduce the gap to less than 1 mm (0.04 inch). (27) The collets and the mating surfaces should be clean. Apply 5P-3931 Anti-Seize Compound to the outside diameter of the collets. Tighten the nuts for the threaded rod to a torque of 1800 200 N m (1325 150 lb ft). Tap the collet assembly until the torque is less than 900 N m (665 lb ft). Torque the nuts to 1800 200 N m (1325 150 lb ft). Tap the collet assembly until the torque for the nuts is less than 1600 N m (1200 lb ft). Torque the nuts again. The torque should be 1800 200 N m (1325 150 lb ft).Note: After fifty hours of operation, torque the nuts to 1800 200 N m (1325 150 lb ft). (30) The collets and the mating surfaces should be clean. Apply 5P-3931 Anti-Seize Compound to the outside diameter of the collets. Tighten the