AVSPARE.COM
parts catalog

HOOK B53902100 - Caterpillar



B53902100 HOOK Caterpillar parts E180 HOOK
Rating:
34
Alternative (cross code) number:
CAB53902100
B5390-2100
B53902100
Caterpillar B53902100 HOOK

Buy HOOK B53902100 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: B53902100:

EXCAVATOR  E180   Caterpillar
Number on catalog scheme: 8
 
  For full view, you need register

Information:

Hydraulic Tank Screen - Clean
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
There is one suction screen in the hydraulic tank. There is one return screen in the hydraulic tank. Clean both screens whenever there is a failure of the brake system, hoist system or another hydraulic component that uses oil from the hydraulic tank. Clean the screens in order to remove the debris.
Illustration 1 g01370458
Relieve the hydraulic tank pressure by pushing on top of breaker relief valve (1) before removing the oil filler cap.
Illustration 2 g01370447
Remove oil filler cap (3) slowly to relieve any remaining pressure.
Illustration 3 g01370450
Note: Hand tighten the NPT pipe nipple. Do not use tools.
Remove hydraulic tank drain plug (6). Install a 1 inch NPT pipe nipple, 88 mm (3.50 inch) long, in the bottom of the tank, to open the internal drain valve. Drain the oil into a suitable container.
Illustration 4 g01370451
Remove bolt (7), return tube (8) and cover (9) .
Remove the valve and return screen assembly.
Wash the valve and return screen assembly in clean, nonflammable solvent.
Install the valve and return screen, cover (9), return tube (8) and bolt (7) .
Illustration 5 g00993359
Remove suction tube (10) .
Remove the suction screen from the hydraulic tank.
Wash the suction screen in clean, nonflammable solvent.
Install the clean suction screen, the suction tube and the retaining bolts.
Illustration 6 g01370454
Remove guard (11) .
Remove front cover (12) from the hydraulic tank.
Clean the debris from the bottom of the hydraulic tank.
Clean the cover for the front of the hydraulic tank in clean, nonflammable solvent. Install a new gasket.
Install cover (12) to the front of the tank.
Install guard (11) .
Fill the hydraulic tank with clean oil. Refer to Operation and Maintenance Manual, "Lubricant Viscosities and Refill Capacities".
When the dump body is fully raised ensure the hydraulic oil level is in the "SAFE START BODY RAISED" range of lower sight gauge (5) .
Start the engine and run the engine at low idle. Check for leaks.
For machines equipped with a dump body check the oil level with the body fully lowered. For machines equipped with an ejector body check the oil level with the ejector plate fully retracted and the tailgate fully raised. With the oil cold maintain the hydraulic oil level to the "FULL COLD" mark in sight gauge (2). With the oil at operating temperature, maintain the hydraulic oil level to the "FULL WARM" mark in sight gauge (2). Add more oil, if necessary through filler tube (4) .
Stop the engine.

Caterpillar parts catalog:

Caterpillar parts catalog
SUPPLEMENT FOR E180 EL180 HYDRAULIC EXCAVATORS /43'/51' LONG REACH F/ 1RF00001-UP (MACHINE)


Parts hook Caterpillar catalog:

0960696 HOOK
E110, E120, E140, E180, E240, E300, E70
0938554 HOOK
E110, E120, E140, E180, E240, E300, E450, E650, E70
0938603 HOOK
E110, E120, E140, E180, E240, E300, E450, E650, E70
0938603 HOOK
E110, E120, E140, E180, E240, E300, E450, E650, E70
0938554 HOOK
E110, E120, E140, E180, E240, E300, E450, E650, E70
0960696 HOOK
E110, E120, E140, E180, E240, E300, E70
3043770 HOOK AS
336E, 336E L, 345D L, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L
3043765 HOOK AS
336E, 336E L, 345D L, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.