0876536 HOSE AS Caterpillar parts
330, 330 FM L, 330 L, 330B L
Rating:
Alternative (cross code) number:
CA0876536
087-6536
0876536
CA0876536
087-6536
0876536
Weight: 5 pounds 2 kg.
EXCAVATOR,
Number on catalog scheme:
5
For full view, you need register
Information:
The fuel filter was removed only for better photo illustration.3. Remove water line (3) from the oil cooler and the elbow on the timing gear cover.4. Remove water line (1) from the oil cooler and the cylinder block.5. Remove 10 bolts (2), and remove cover (4) and the core assembly as a unit from the oil cooler support (base). 6. Remove cover (4) from the core assembly. 7. Carefully lift out each side of divider (5); then slide it out from between the plates of the core.
Typical Example8. Remove six bolts (6) and support (base) (7) from the engine. 9. Remove O-ring seals (8) from the support (base).10. Remove plug (9), the O-ring seal, the spring and valve from the support (base). The following steps are for installation of the engine oil cooler, support (base) and bypass valve.11. Install O-ring seals (8) in the support (base).12. Install the O-ring seal on plug (9). Install the valve, spring and plug (9) in the support (base).13. Put support (base) (7) in position onethe engine. Install the six bolts that hold it in place.14. Install divider (5) between the fifth and sixth plates from the mounting flange on the cover. Be sure the base on the divider is on the side opposite the two mounting on the flange of the cover that are not evenly spaced.15. Install the gasket and cover on core (4) as shown.16. Install the gasket with the indexing point toward the rear of the engine and in the up position. Put the oil cooler core and cover (4) on the support (base). Install the bolts that hold it, and tighten them to a torque of 31 4 N m (23 3 lb.ft.).17. Install water line (1), and tighten the hose clamps.18. Install water line (3), and tighten the hose clamps.19. Check the oil level in the engine. Fill the engine with oil to the correct level if necessary. See the Maintenance Guide.20. Fill the cooling system with coolant to the correct level. See the Maintenance Guide.
Typical Example8. Remove six bolts (6) and support (base) (7) from the engine. 9. Remove O-ring seals (8) from the support (base).10. Remove plug (9), the O-ring seal, the spring and valve from the support (base). The following steps are for installation of the engine oil cooler, support (base) and bypass valve.11. Install O-ring seals (8) in the support (base).12. Install the O-ring seal on plug (9). Install the valve, spring and plug (9) in the support (base).13. Put support (base) (7) in position onethe engine. Install the six bolts that hold it in place.14. Install divider (5) between the fifth and sixth plates from the mounting flange on the cover. Be sure the base on the divider is on the side opposite the two mounting on the flange of the cover that are not evenly spaced.15. Install the gasket and cover on core (4) as shown.16. Install the gasket with the indexing point toward the rear of the engine and in the up position. Put the oil cooler core and cover (4) on the support (base). Install the bolts that hold it, and tighten them to a torque of 31 4 N m (23 3 lb.ft.).17. Install water line (1), and tighten the hose clamps.18. Install water line (3), and tighten the hose clamps.19. Check the oil level in the engine. Fill the engine with oil to the correct level if necessary. See the Maintenance Guide.20. Fill the cooling system with coolant to the correct level. See the Maintenance Guide.
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 1673C, 16H, 16M, 215B, 235B, 235D, 3176C, 3196, 330, 330 L...
120B, 120G, 130G, 140B, 1673C, 225, 235, 235B, 235C, 235D, 245B, 3176B, 3176C, 3196, 330 L, 3304, 3304B, 3306, 3306B, 330B, 3406E, 350, 627B, 637D, 776, 777, 777B, 784C, 785, 785C, 785D, 854G, 85C, 85...
307C, 308D, 312C, 312C L, 314C, 316E L, 318C, 318E L, 319C, 320B, 320C, 320C L, 320D FM, 320D L, 320D LN, 321C, 321D LCR, 322B, 322B L, 322C, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D ...
307C, 312C, 312C L, 315C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 322 LN, 322B, 322B L, 322B LN, 322C, 325 LN, 325B L, 325C, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 345B II, 345B L, 385B, 385C, 385C...
307C, 308C, 315C, 315D L, 319D L, 320B, 320C, 320C FM, 320C L, 320D, 320D L, 320D LRR, 320D RR, 320E LRR, 321D LCR, 322, 322 FM L, 322B, 322B L, 322C, 322C FM, 323D L, 324D FM, 325, 325 L, 325 LN, 325...
308C, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314C, 315D L, 318D L, 318D2 L, 319D, 319D L, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
311C, 311D LRR, 311F LRR, 312C, 312D, 312D L, 315C, 315D L, 318C, 318D L, 318D2 L, 319C, 319D, 319D L, 320B, 320C, 320D, 320D L, 320D LRR, 320D RR, 320D2 L, 321C, 321D LCR, 322, 322 FM L, 322 LN, 322B...
229D, 325B L, 325C, 330B L, 330C, 345B II, 345B L, 980F, 980F II, 980G, 980G II, 980H, 990, 990 II, 990H, 993K
322C, 322C FM, 325C, 330B, 330B L, W330B
324D, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 365B II, 385B
320 L, 322 L, 322B, 325, 325 L, 325B L, 325C L, 330B L, 345B II, 345B L
325C, 330B, 330B L, 330C, 330C FM, 330C L, OEMS
0876539
HOSE AS
330, 330 FM L, 330 L
330, 330 FM L, 330 L
4I5766
HOSE AS
330, 330 FM L, 330 L
330, 330 FM L, 330 L
1110937
HOSE AS
330, 330 L
330, 330 L
330, 330 L
330, 330 L
7Y7979
HOSE AS
330, 330 FM L, 330 L
330, 330 FM L, 330 L
330, 330 L, 330B, 330B L, W330B
1021115
HOSE AS
330, 330 FM L, 330 L
330, 330 FM L, 330 L
1021111
HOSE AS
330, 330 FM L, 330 L
330, 330 FM L, 330 L
5I7474
HOSE AS
330, 330 FM L
330, 330 FM L
4I6068
HOSE AS
330, 330 FM L, 330 L
330, 330 FM L, 330 L
325, 325 L, 325 LN, 330, 330 FM L, 330 L, 345B II, 345B L