0876545 HOSE AS Caterpillar parts
325 L, 325 LN, 330, 330 FM L, 330 L
Rating:
Alternative (cross code) number:
CA0876545
087-6545
0876545
CA0876545
087-6545
0876545
Weight: 7 pounds 3 kg.
EXCAVATOR,
Number on catalog scheme:
47
For full view, you need register
Information:
4. Remove tube assembly (4). Loosen hose clamp (5) between the cylinder head assembly and timing gear cover.5. Remove 22 bolts (6) that hold the cylinder head assembly to the cylinder block. Fasten tool (A) and a hoist to the cylinder head assembly. Remove the cylinder head assembly. Weight is 54 kg (120 lb.).Install Cylinder Head Assembly
1. Clean the surfaces of the cylinder head assembly and the cylinder block that make contact with each other. Check the cylinder head and cylinder block deck for flatness. The overall flatness for both the cylinder block and cylinder head should be 0.15 mm (.006 in.) or less. The maximum allowable for any 152.4 mm (6.00 in.) span is 0.08 mm (.003 in.). Make sure the surfaces are clean and dry. Install a new dry gasket on the cylinder block. 2. Inspect the condition of water ferrule and seal (2). Make a replacement if needed. Put water ferrule and seal (2) in position with the adjusting screw of hose clamp (1) toward the top and approximately 45° to the right of vertical as seen from the front of the engine.3. Make sure the seal is installed all the way in the counterbore. If the plugs in the oil passages in the cylinder head were removed, put 5P3413 Pipe Sealant with Teflon on the threads, and install the plugs in the head. 4. Fasten tool (A) and a hoist to the cylinder head assembly. Put cylinder head assembly (3) in position on the cylinder block.5. Put 5P3931 Anti-Seize Compound on all the threads of the head bolts.
Head Bolt Location And Tightening Sequence6. Install the head bolts, and tighten as follows:a. Tighten bolts (1) to (18) by number sequence to a torque of 80 14 N m (60 10 lb.ft.).b. Tighten bolts (1) to (18) by number sequence to a torque of 150 7 N m (110 5 lb.ft.).c. Tighten bolts (1) to (18) again by number sequence to a torque of 150 7 N m (110 5 lb.ft.).d. Tighten bolts (19) to (22) by number sequence to a torque of 43 7 N m (32 lb.ft.). 7. Tighten hose clamp (1).8. Install tube assembly (4). 9. Install the gasket and air inlet elbow (7) on the cylinder head assembly.10. Connect hose (5) for the air cleaner indicator to air inlet elbow (7). Connect line (6) for the ether starting aid to the air inlet elbow.11. Fasten a hoist to the hood, and put the hood in position on the machine. Weight of the hood is 25 kg (55 lb.). Install the four bolts that hold the hood in place. Install the clip on the top coolant tube.END BY:a. install mufflerb. install exhaust manifoldc. install air cleaner housingd. install fuel injection nozzlese. lower cab **This operation is in the Vehicle Systems Disassembly And Assembly section.Disassemble Cylinder Head Assembly
START BY:a. remove cylinder head assembly New cylinder head components are effective with the 943 and 953 Loaders with
1. Clean the surfaces of the cylinder head assembly and the cylinder block that make contact with each other. Check the cylinder head and cylinder block deck for flatness. The overall flatness for both the cylinder block and cylinder head should be 0.15 mm (.006 in.) or less. The maximum allowable for any 152.4 mm (6.00 in.) span is 0.08 mm (.003 in.). Make sure the surfaces are clean and dry. Install a new dry gasket on the cylinder block. 2. Inspect the condition of water ferrule and seal (2). Make a replacement if needed. Put water ferrule and seal (2) in position with the adjusting screw of hose clamp (1) toward the top and approximately 45° to the right of vertical as seen from the front of the engine.3. Make sure the seal is installed all the way in the counterbore. If the plugs in the oil passages in the cylinder head were removed, put 5P3413 Pipe Sealant with Teflon on the threads, and install the plugs in the head. 4. Fasten tool (A) and a hoist to the cylinder head assembly. Put cylinder head assembly (3) in position on the cylinder block.5. Put 5P3931 Anti-Seize Compound on all the threads of the head bolts.
Head Bolt Location And Tightening Sequence6. Install the head bolts, and tighten as follows:a. Tighten bolts (1) to (18) by number sequence to a torque of 80 14 N m (60 10 lb.ft.).b. Tighten bolts (1) to (18) by number sequence to a torque of 150 7 N m (110 5 lb.ft.).c. Tighten bolts (1) to (18) again by number sequence to a torque of 150 7 N m (110 5 lb.ft.).d. Tighten bolts (19) to (22) by number sequence to a torque of 43 7 N m (32 lb.ft.). 7. Tighten hose clamp (1).8. Install tube assembly (4). 9. Install the gasket and air inlet elbow (7) on the cylinder head assembly.10. Connect hose (5) for the air cleaner indicator to air inlet elbow (7). Connect line (6) for the ether starting aid to the air inlet elbow.11. Fasten a hoist to the hood, and put the hood in position on the machine. Weight of the hood is 25 kg (55 lb.). Install the four bolts that hold the hood in place. Install the clip on the top coolant tube.END BY:a. install mufflerb. install exhaust manifoldc. install air cleaner housingd. install fuel injection nozzlese. lower cab **This operation is in the Vehicle Systems Disassembly And Assembly section.Disassemble Cylinder Head Assembly
START BY:a. remove cylinder head assembly New cylinder head components are effective with the 943 and 953 Loaders with
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
307, 307C, 312C L, 320 L, 320B, 320C, 320D, 320D FM, 320D FM RR, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E L, 320N, 323D L, 323D2 L, 325, 325 LN, 325B L, 325C L, 345B, 345B II, 345B II MH,...
307C, 311C, 311D LRR, 312C, 312C L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320C, 320D, 3...
308C, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314C, 315D L, 318D L, 318D2 L, 319D, 319D L, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
308C, 311C, 311F LRR, 312C, 312C L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D FM RR,...
308C, 312C, 312C L, 312D, 314C, 315C, 315D L, 318D2 L, 319D L, 320 L, 320B, 320C, 320D, 320D L, 320D LRR, 320D2 L, 320E, 320E L, 320E LN, 321D LCR, 322B, 322B L, 322B LN, 322C FM, 323E L, 324D, 324D F...
308C, 311C, 311D LRR, 311F LRR, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 318C, 319C, 320C, 320D, 320E L, 320E LN, 321C, 321D LCR, 322C, 322C FM, 323E L, 325 L, 325B, 325C, 325C FM, 325D L, 33...
312E, 312E L, 314E CR, 314E LCR, 315D L, 316E L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D L...
215, 215B, 311, 312, 312B, 315, 315B, 315B FM L, 320, 320 L, 320B, 320B FM LL, 320B L, 320B U, 320C, 320N, 322, 322 L, 322B, 322B L, 325, 325B, 325B L, 325C L, 330, 330 L, 330B, 330B L, 345B L, 350, 3...
324D, 324D L, 324D LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D2 L, 365B
324D, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 365B II, 385B
325B L, 330, 330 FM L, 330 L, 330B, 330B L
325B L, 330, 330 FM L, 330 L, 330B, 330B L
0875055
HOSE AS
330, 330 FM L, 330 L
330, 330 FM L, 330 L
0875058
HOSE AS
330, 330 FM L, 330 L, 330B, 330B L, W330B
330, 330 FM L, 330 L, 330B, 330B L, W330B
0875061
HOSE AS
330, 330 FM L, 330 L, 330B, 330B L, W330B
330, 330 FM L, 330 L, 330B, 330B L, W330B
0875063
HOSE AS
330, 330 FM L, 330 L, 330B L
330, 330 FM L, 330 L, 330B L
330, 330 L, 330B, 330B L, W330B
330, 330 L, 330B, 330B L, W330B
1132899
HOSE-WATER
325, 325 L, 330
325, 325 L, 330
1018803
HOSE AS
330, 330 FM L, 330 L
330, 330 FM L, 330 L
4I0809
HOSE AS
330, 330 FM L, 330 L, 330B
330, 330 FM L, 330 L, 330B
4I0830
HOSE AS
330, 330 FM L, 330 L, 330B
330, 330 FM L, 330 L, 330B
4I0827
HOSE AS
330, 330 FM L, 330 L, 330B
330, 330 FM L, 330 L, 330B
4I0842
HOSE AS
330, 330 FM L, 330 L, 330B
330, 330 FM L, 330 L, 330B