1023922 HOSE-SUPPLY Caterpillar parts
350
Rating:
Alternative (cross code) number:
CA1023922
102-3922
1023922
CA1023922
102-3922
1023922
Weight: 1 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 1023922:
Number on catalog scheme:
5
For full view, you need register
Information:
Replacement Of 6V4176 Display Unit
If one or more segments do not show the correct reading on the 6V4176 Display Unit for RPM at location (A) or DEG at location (B), the problem is most likely with the display unit at either location. Be sure to check for a good connection for each display unit. Use the procedure that follows to remove a display unit. 1 Remove the six screws (1) from front panel (2), and remove panel (2) from case (3).2 Remove the four screws (4) from the PC board, and also remove the locknuts from the two front panel switches (5) and (6). 3 Carefully lift front panel (2) from PC (printed circuit) board (7).4 To remove either display unit, (A) or (B), use a screwdriver as shown, and carefully remove the unit from its position in the PC board. Before the removal of either display unit, look carefully in the area of location (C), for some type of identification mark on the display unit and on the PC board. This needs to be done to make sure that at time of installation, the display unit will be installed correctly. At installation of a display unit, be very careful and make sure the pins on the display unit are in alignment with the socket holes.Replacement Of 6V4179 Digital Voltmeter Integrated Circuit
If one or more segments of either 6V4176 Display Unit, RPM or DEG [location (A) or (B)] do not work, see REPLACEMENT OF 6V4176 DISPLAY UNIT. After a display unit has been checked and/or a replacement installed and there is still a problem; or, if one display unit is completely blank while the other one works normally, the problem can be with a 6V4179 Digital Voltmeter (DVM) Integrated Circuit. There are two 6V4179 DVM Integrated Circuits in each 6V3100 Timing Indicator. 1 Remove six screws (1), then remove panel (2) from case (3). 2 Use the hook end of 5P1720 Seal Pick (4) and carefully remove the DVM integrated circuit, (5) or (6), as shown. [Use the notch at end (A) of the DVM as a reference mark to be used at time of installation.] At installation of a DVM, put the reference mark, as given in step 2, in the correct location. Also, be sure that the pins on the DVM are in alignment with the holes in the socket.Parts And Repair Service Information
When one of the parts used with the timing indicator group is to be returned for a repair or warranty service, always give the following information: 1. Description of the type of problem.2. Where to send part after repair.3. Serial number (if applicable).4. Person the part should be sent to.5. Billing address if different than shipping address.6V3100 Engine Timing Indicator Group
For electronic repair of the timing indicator group, see Special Instruction Form SEHS8135.For warranty or repair work for the 6V3100 Engine Timing Indicator Group (except for 6V2192 Injection Transducer, 6V2197 Magnetic Transducer, or 6V7910 Injection Transducer) send the indicator group to:Snap-On Tool Corporation
Midwest
If one or more segments do not show the correct reading on the 6V4176 Display Unit for RPM at location (A) or DEG at location (B), the problem is most likely with the display unit at either location. Be sure to check for a good connection for each display unit. Use the procedure that follows to remove a display unit. 1 Remove the six screws (1) from front panel (2), and remove panel (2) from case (3).2 Remove the four screws (4) from the PC board, and also remove the locknuts from the two front panel switches (5) and (6). 3 Carefully lift front panel (2) from PC (printed circuit) board (7).4 To remove either display unit, (A) or (B), use a screwdriver as shown, and carefully remove the unit from its position in the PC board. Before the removal of either display unit, look carefully in the area of location (C), for some type of identification mark on the display unit and on the PC board. This needs to be done to make sure that at time of installation, the display unit will be installed correctly. At installation of a display unit, be very careful and make sure the pins on the display unit are in alignment with the socket holes.Replacement Of 6V4179 Digital Voltmeter Integrated Circuit
If one or more segments of either 6V4176 Display Unit, RPM or DEG [location (A) or (B)] do not work, see REPLACEMENT OF 6V4176 DISPLAY UNIT. After a display unit has been checked and/or a replacement installed and there is still a problem; or, if one display unit is completely blank while the other one works normally, the problem can be with a 6V4179 Digital Voltmeter (DVM) Integrated Circuit. There are two 6V4179 DVM Integrated Circuits in each 6V3100 Timing Indicator. 1 Remove six screws (1), then remove panel (2) from case (3). 2 Use the hook end of 5P1720 Seal Pick (4) and carefully remove the DVM integrated circuit, (5) or (6), as shown. [Use the notch at end (A) of the DVM as a reference mark to be used at time of installation.] At installation of a DVM, put the reference mark, as given in step 2, in the correct location. Also, be sure that the pins on the DVM are in alignment with the holes in the socket.Parts And Repair Service Information
When one of the parts used with the timing indicator group is to be returned for a repair or warranty service, always give the following information: 1. Description of the type of problem.2. Where to send part after repair.3. Serial number (if applicable).4. Person the part should be sent to.5. Billing address if different than shipping address.6V3100 Engine Timing Indicator Group
For electronic repair of the timing indicator group, see Special Instruction Form SEHS8135.For warranty or repair work for the 6V3100 Engine Timing Indicator Group (except for 6V2192 Injection Transducer, 6V2197 Magnetic Transducer, or 6V7910 Injection Transducer) send the indicator group to:Snap-On Tool Corporation
Midwest
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
120G, 215, 215B, 215D, 225, 229, 229D, 235, 235C, 235D, 245, 245B, 307, 307B, 312, 312B L, 312C, 315, 315B L, 315C, 317, 317B LN, 318B, 318C, 320 L, 3208, 320B, 322, 322 LN, 325, 330 FM L, 330 L, 3412...
330, 330 FM L, 330 L, 3306, 3306C, 330B, 330B L, 350, 525, 527, 627B, 65C, 966F, 966F II, 972G, D250E, D250E II, D25D, D300E, D300E II, W330B
120B, 120G, 130G, 140B, 1673C, 225, 235, 235B, 235C, 235D, 245B, 3176B, 3176C, 3196, 330 L, 3304, 3304B, 3306, 3306B, 330B, 3406E, 350, 627B, 637D, 776, 777, 777B, 784C, 785, 785C, 785D, 854G, 85C, 85...
120K, 120K 2, 120M, 12K, 12M, 140G, 140K, 140K 2, 140M, 160K, 160M, 16M, 216, 228, 236, 236B, 236D, 242B, 242D, 246D, 247, 247B, 248, 257D, 259D, 262D, 267, 267B, 268B, 272D, 272D XHP, 277D, 279D, 287...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 30...
307, 307C, 312C L, 320 L, 320B, 320C, 320D, 320D FM, 320D FM RR, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E L, 320N, 323D L, 323D2 L, 325, 325 LN, 325B L, 325C L, 345B, 345B II, 345B II MH,...
307B, 307C, 308C, 311D LRR, 311F LRR, 312C L, 314C, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
307C, 307D, 307E, 311C, 311D LRR, 311F LRR, 312D, 312D L, 314C, 314D LCR, 314E LCR, 320B, 320C, 320C FM, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B, 322B LN...
308C, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314C, 315D L, 318D L, 318D2 L, 319D, 319D L, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
308C, 311C, 311F LRR, 312C, 312C L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D FM RR,...
308C, 312C, 312C L, 312D, 314C, 315C, 315D L, 318D2 L, 319D L, 320 L, 320B, 320C, 320D, 320D L, 320D LRR, 320D2 L, 320E, 320E L, 320E LN, 321D LCR, 322B, 322B L, 322B LN, 322C FM, 323E L, 324D, 324D F...
320B, 320B L, 322B L, 325B L, 330B L, 345B, 345B II, 345B II MH, 350, 375, 375 L, 5080, 938F, 966D, 966F, 966F II, 970F, IT38F, M325B, W345B II
7Y1418
HOSE
330, 330 FM L, 330 L, 330B, 330B L, 350, W330B
330, 330 FM L, 330 L, 330B, 330B L, 350, W330B
4I7501
HOSE
330B, 330B L, 350, W330B
330B, 330B L, 350, W330B
7Y5843
HOSE AS
350
350
7I8480
HOSE AS
350
350
4I2534
HOSE AS
350
350
1023880
HOSE-AIR
350
350
7Y1993
HOSE-AIR
350
350