1048990 HOSE Caterpillar parts
375, 375 L, 5080
Rating:
Alternative (cross code) number:
CA1048990
104-8990
1048990
CA1048990
104-8990
1048990
Weight: 3 pounds 1 kg.
Information:
ID
117.48
mm
LENGTH
380
mm
EXCAVATOR, FRONT SHOVEL,
Number on catalog scheme:
10
For full view, you need register
Information:
Illustration 4 g01155187
Connector for the engine speed/timing sensors
(1) Speed/timing sensor (−)
(2) Speed/timing sensor (+)
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit for the engine speed/timing sensor.
Check the allen head screw for each ECM connector for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Check the harness and wiring for abrasion and for pinch points from the engine speed/timing sensors to the ECM. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and the wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals for the connectors are properly in place and ensure that the connectors are completely coupled. Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Restore the electrical power to the ECM.
Start the engine and run the engine. The problem may occur when the engine is at any operating temperature. However, the problem is more likely to occur when the engine is at the normal operating temperature.
If the engine will not start, monitor the engine speed on Cat ET while the engine is being cranked. Cat ET may need to be powered from another battery while the engine is being cranked. This is done so that Cat ET will not reset. Note: Upon initial cranking, the status for engine speed may indicate that the engine speed signal is abnormal. This message should be replaced with an engine speed once the ECM is able to calculate a speed from the signal.
Check for one of the following logged diagnostic codes or active diagnostic codes:
190-08 Engine Speed signal abnormal
342-08 Secondary Engine Speed signal abnormalExpected Result:One of the above codes are active or logged.Results:
No engine rpm - Engine rpm is not indicated on Cat ET. Proceed to Test Step 3.
Active or logged code - There is an active diagnostic code or a logged diagnostic code for an engine speed/timing sensor. Proceed to Test Step 4.
No codes - Neither code is active or logged.Repair: Refer to the appropriate symptoms in Troubleshooting, "Troubleshooting Without a Diagnostic Code".STOPTest Step 3. Check the Installation of the Sensor Assembly
Remove the electrical power from the ECM.
Illustration 5 g01434702
Sensor installation
(4) Mounting surface
(5) Flange
(6) Bracket
Visually inspect the sensors without removing the sensor assembly from the engine. Flange (5) must be flush against mounting surface (4) in order to ensure proper operation. Inspect bracket (6). Verify that the bracket securely holds the flange of the sensor flush against the mounting surface.Verify that the bracket is not bent. If the bracket is bent or if an obstruction is preventing the sensor assembly from being installed correctly, the engine will not start.Note: The bracket cannot be replaced
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
130G, 215, 215B, 215C, 215D, 225, 227, 231D, 235, 235B, 235C, 245, 375, 375 L, 587T, 631D, 815B, 825C, 826C, 914G, 924G, 924GZ, 926, 928G, 936, 936F, 938G, 950B, 950B/950E, 950F, 966D, 966F, 980C, 980...
307, 307C, 312C L, 320 L, 320B, 320C, 320D, 320D FM, 320D FM RR, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E L, 320N, 323D L, 323D2 L, 325, 325 LN, 325B L, 325C L, 345B, 345B II, 345B II MH,...
307C, 308D, 312C, 312C L, 314C, 316E L, 318C, 318E L, 319C, 320B, 320C, 320C L, 320D FM, 320D L, 320D LN, 321C, 321D LCR, 322B, 322B L, 322C, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D ...
307B, 307C, 308C, 311D LRR, 311F LRR, 312C L, 314C, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D...
307C, 311C, 311D LRR, 312C, 312C L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320C, 320D, 3...
307C, 308C, 311C, 311D LRR, 311F LRR, 312C, 312D, 312D L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D FM RR, 320D L, 320D LN, 320D...
308C, 312C L, 312D, 312D L, 315C, 315D L, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 322...
311C, 312C, 315C, 318C, 319C, 320B, 320C, 320C FM, 320D, 320D FM RR, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 322B, 322C FM, 323D LN, 324D, 324D LN, 325 LN, 325C, 325D, 325D FM LL, 325D L, 325D MH, ...
314C, 314D CR, 314D LCR, 314E CR, 320B, 320C FM, 320D, 320D L, 323D L, 324E LN, 325B L, 325D FM, 325D FM LL, 328D LCR, 330B, 330B L, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D...
320 L, 330 L, 375, 966D, 966F, 966F II, 970F, IT12B
320B, 320B L, 322B L, 325B L, 330B L, 345B, 345B II, 345B II MH, 350, 375, 375 L, 5080, 938F, 966D, 966F, 966F II, 970F, IT38F, M325B, W345B II
1087222
HOSE AS
375, 5080
375, 5080
1087209
HOSE AS
375, 5080
375, 5080
1087202
HOSE AS
375, 5080
375, 5080
1087201
HOSE AS
375, 5080
375, 5080
1481597
HOSE AS
375, 5080
375, 5080
1481600
HOSE AS
375, 5080
375, 5080
4I7626
HOSE AS
375, 375 L, 5080
375, 375 L, 5080
1031291
HOSE AS
375, 375 L, 5080
375, 375 L, 5080
7I1019
HOSE AS
375, 375 L, 5080
375, 375 L, 5080
375, 375 L, 5080
7Y4176
HOSE AS
375, 375 L, 5080
375, 375 L, 5080
375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5080, 5090B