1319015 HOSE-UPPER Caterpillar parts
315B, 315B FM L, 317B LN, 318B
Rating:
Alternative (cross code) number:
CA1319015
131-9015
1319015
CA1319015
131-9015
1319015
Weight: 0.92 pounds 0 kg.
EXCAVATOR,
Number on catalog scheme:
3
For full view, you need register
Information:
Start By:
Remove the stick.
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Note: For the removal of the sleeve bearings from the stick at the pin joint for the bucket control linkage, refer to Disassembly and Assembly, "Bucket Linkage Bearings and Seals - Remove".
Illustration 1 g00592359
Remove lip seal (1).
Illustration 2 g00592391
Use Tooling (A) to remove the sleeve bearing.
Repeat Steps 1 and 2 to remove the lip seal and the sleeve bearing from the opposite side of the stick.
Illustration 3 g00604131
Remove lip seal (2) from the bore for the stick to bucket pin.
Illustration 4 g01302540
Use Tooling (A) to remove the sleeve bearing.
Repeat Steps 4 and 5 to remove the lip seal and the sleeve bearing from the opposite side of the stick.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B - Molybdenum Grease -
C 1P-0520 Driver Gp 1 Note: Make sure that the bearing bores for the sleeve bearings are free of paint and grease prior to the installation of the sleeve bearings.
Lower the temperature of the new sleeve bearing for the heel end of the stick.
Insert the new sleeve bearing into the stick at the connection of the stick and the heel.
Illustration 5 g02728379
(D) 9.5 0.8 mm (0.374 0.032 inch)
Use Tooling (C) to drive the new sleeve bearing into the bearing bore in the stick. Drive the new sleeve bearing into the bearing bore to the depth of Dimension (D).
Illustration 6 g02728393
Use Tooling (C) to install lip seal (1) in the outside of the sleeve bearing. Install lip seal (1) so that the lip faces outward. Drive the seal until the seal contacts the sleeve bearing. Apply Tooling (B) to the sealing lip of lip seal (1) and to the sleeve bearings.
Repeat Step 1 through Step 4 for installation of the sleeve bearing and
Remove the stick.
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Note: For the removal of the sleeve bearings from the stick at the pin joint for the bucket control linkage, refer to Disassembly and Assembly, "Bucket Linkage Bearings and Seals - Remove".
Illustration 1 g00592359
Remove lip seal (1).
Illustration 2 g00592391
Use Tooling (A) to remove the sleeve bearing.
Repeat Steps 1 and 2 to remove the lip seal and the sleeve bearing from the opposite side of the stick.
Illustration 3 g00604131
Remove lip seal (2) from the bore for the stick to bucket pin.
Illustration 4 g01302540
Use Tooling (A) to remove the sleeve bearing.
Repeat Steps 4 and 5 to remove the lip seal and the sleeve bearing from the opposite side of the stick.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B - Molybdenum Grease -
C 1P-0520 Driver Gp 1 Note: Make sure that the bearing bores for the sleeve bearings are free of paint and grease prior to the installation of the sleeve bearings.
Lower the temperature of the new sleeve bearing for the heel end of the stick.
Insert the new sleeve bearing into the stick at the connection of the stick and the heel.
Illustration 5 g02728379
(D) 9.5 0.8 mm (0.374 0.032 inch)
Use Tooling (C) to drive the new sleeve bearing into the bearing bore in the stick. Drive the new sleeve bearing into the bearing bore to the depth of Dimension (D).
Illustration 6 g02728393
Use Tooling (C) to install lip seal (1) in the outside of the sleeve bearing. Install lip seal (1) so that the lip faces outward. Drive the seal until the seal contacts the sleeve bearing. Apply Tooling (B) to the sealing lip of lip seal (1) and to the sleeve bearings.
Repeat Step 1 through Step 4 for installation of the sleeve bearing and
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
120B, 120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H NA, 140B, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 215, ...
120G, 215, 215B, 215D, 225, 229, 229D, 235, 235C, 235D, 245, 245B, 307, 307B, 312, 312B L, 312C, 315, 315B L, 315C, 317, 317B LN, 318B, 318C, 320 L, 3208, 320B, 322, 322 LN, 325, 330 FM L, 330 L, 3412...
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
120K, 120K 2, 120M, 12K, 12M, 140G, 140K, 140K 2, 140M, 160K, 160M, 16M, 216, 228, 236, 236B, 236D, 242B, 242D, 246D, 247, 247B, 248, 257D, 259D, 262D, 267, 267B, 268B, 272D, 272D XHP, 277D, 279D, 287...
120H, 120H ES, 120H NA, 120M 2, 135H, 135H NA, 236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 2864C, 287D, 289D, 299D, 299D XHP, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 30...
312, 312B L, 312C, 315B L, 317B LN, 966D, 966F, 966F II, 970F
315, 315B L, 317, 317B LN, 318C, 319C, 320 L, 320B, 320B L, 320B U, 320C, 320N, 321B, 321C, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 328D LCR, 330, 330 FM L, 330 L
315, 315B, 315B L, 317, 317B LN, 318B, 320 L, 320B, 320B FM LL, 320N
307B, 311B, 312B, 312B L, 315B, 318B, 320B, 320B L, 320B U, 320N, 321B
315B, 315B L, 315C, 315D L, 316E L, 317B LN, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 32...
315, 315B, 315C, 317B LN, 318B, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
2092244
HOSE AS
302.5
302.5
2092243
HOSE AS
302.5
302.5
1593772
HOSE AS
302.5
302.5
1538385
HOSE AS
302.5
302.5
1538384
HOSE AS
302.5, 302.5C
302.5, 302.5C
1538383
HOSE AS
302.5, 902, 906
302.5, 902, 906
1516628
HOSE
307B
307B
1567337
HOSE AS
317B LN
317B LN
1666113
HOSE-AIR
315B, 317B LN, 318B, D5C III
315B, 317B LN, 318B, D5C III
1076341
HOSE
315, 315B, 317B LN, 318B, 939, 939C, D5C III
315, 315B, 317B LN, 318B, 939, 939C, D5C III
1023884
HOSE-AIR
315, 315B, 317B LN
315, 315B, 317B LN
1319016
HOSE-LOWER
315B, 315B FM L, 317B LN
315B, 315B FM L, 317B LN