AVSPARE.COM
parts catalog

HOSE AS 1400422 - Caterpillar



1400422 HOSE AS Caterpillar parts HOSE
Rating:
56
Alternative (cross code) number:
CA1400422
140-0422
1400422
Caterpillar 1400422 HOSE AS

Buy HOSE AS 1400422 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

8. Install shaft (14) on gear (8). Install the eight bolts that hold it in place. 9. Put clean SAE 30 oil on each plate and disc. Install seven plates (18) and seven discs (17) on the gear. Start with a plate and make sure there is a disc between each plate. Install six springs (15) and plate (16). 10. Put a thin layer of clean SAE 30 oil on the lip of ring seal (7). Install piston (19). Make sure dowels (13) are in alignment with holes (20). Holes (20) are not as deep as the remainder of the holes in the piston. Springs (15) must be in alignment with the remainder of the holes. 11. Install seal (21) with the lip down as shown. Install O-ring seal (23). Install plate (22) in the piston. The notch in the plate must be in alignment with the dowel on the shaft. 12. Install bearing cone (24) and spacer (25). 13. Install ring (26) in the drum. 14. Use tooling (C) and a press to install bearing cup (27) in the drum against the ring. 15. Install spacer (28) in the drum so that the step in the spacer is toward the ring in the drum. 16. Use tooling (C) and a press to install the bearing cup in drum (29) so that the bearing cup is against the spacer. 17. Install drum (29) over the discs. Install bearing cone (32), washer (31) and lock (30) on the shaft. 18. Put 5P3931 Anti-Seize Compound on the face and threads of nut (33). Install the nut and use tool (D) to tighten the nut to a torque of 210 20 lb.ft. (285 27 N m). Make a bend in the lock. 19. Heat bearing cone (34) to a temperature of 275°F (135°C) and install it on the shaft.20. Repeat Steps 4 through 19 for the other directional clutch. 21. Install a 3/4"-10 NC forged eyebolt in the directional clutches. Install directional clutches (35) in the transfer gear case. The weight of the directional clutches is approximately 150 lb. (68 kg). 22. Heat bearing cones (36) and (37) to a temperature of 275°F (135°C) for one hour. Install the bearing cones on pump drive shaft (38). 23. Install the pump drive shaft (38) in the transfer gear case. 24. Install spiral ring (39) in the idler gear. Make a note of dimensions (X) and (Y). One dimension will be larger than the other. Make a mark on the side of the gear that has the smaller dimension. 25. Use tooling (C) and a press to install bearing cup (40) in the side of idler gear with smaller dimension as seen in Step 24. Install the bearing cup so that it is against spiral ring (39). 26. Install spacer (41) in the gear so that the step in the spacer is toward spiral ring (39). 27. Use tooling (C) to install bearing cup (42) in the other side of the


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.