1U3558 HOSE AS Caterpillar parts
D8L, D9N
Rating:
Alternative (cross code) number:
CA1U3558
1U-3558
1U3558
CA1U3558
1U-3558
1U3558
Weight: 2 pounds 1 kg.
TRACK-TYPE TRACTOR,
Number on catalog scheme:
1
For full view, you need register
Information:
Removal Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Turn the power disconnect switch to the OFF position. Shut off the fuel supply.
Illustration 1 g01579815
Disconnect hose assemblies (1). Disconnect harness assembly (3). Remove filter assembly (2) .
Illustration 2 g01579816
Disconnect tube assemblies (5). Disconnect harness assembly (4). Remove sensor (6). Remove filter assembly (7) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 3 g01579816
Install filter assembly (7). Connect tube assemblies (5). Connect harness assembly (4). Install sensor (6).
Illustration 4 g01579815
Connect hose assemblies (1). Connect harness assembly (3). Install filter assembly (2) .
Turn on the fuel supply. Turn the power disconnect switch to the ON position.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Turn the power disconnect switch to the OFF position. Shut off the fuel supply.
Illustration 1 g01579815
Disconnect hose assemblies (1). Disconnect harness assembly (3). Remove filter assembly (2) .
Illustration 2 g01579816
Disconnect tube assemblies (5). Disconnect harness assembly (4). Remove sensor (6). Remove filter assembly (7) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 3 g01579816
Install filter assembly (7). Connect tube assemblies (5). Connect harness assembly (4). Install sensor (6).
Illustration 4 g01579815
Connect hose assemblies (1). Connect harness assembly (3). Install filter assembly (2) .
Turn on the fuel supply. Turn the power disconnect switch to the ON position.
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
120K, 120K 2, 120M, 12K, 12M, 140K, 140K 2, 140M, 160K, 160M, 16M, 235, 245, 245B, 24H, 24M, 3126, 3126B, 3176B, 3176C, 3196, 3208, 3304, 3306, 3306B, 3406, 3406C, 3406E, 3408, 3408C, 3412, 3412C, 341...
12M, 140G, 140M, 245B, 24M, 3114, 3116, 3126, 3126B, 3176B, 3176C, 3196, 3208, 3304, 3306, 3306B, 3406, 3406B, 3406E, 3408, 3408B, 3412, 3412C, 3412D, 3412E, 446, 515, 518, 518C, 525, 554, 574, 594H, ...
1674, 16G, 245, 3306C, 3406, 3406B, 3406E, 3408, 3408C, 3456, 3508, 3508B, 3512, 3512B, 3516, 3516B, 578, 583R, 587R, 589, 621B, 65C, 768C, 769C, 771C, 824C, 834B, 836, 980C, 988B, 988F, CG137-12, D44...
24H, 30/30, 5110B, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 769C, 769D, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 834B, 836, 844, 988B, 988F II, 990, 990 II, 992C, BG-260D, C32, D10R, D8L, D...
3408, 3606, 3608, 589, C280-16, C280-6, C280-8, D8L, D9N
D6R, D6R II, D6R III, D6T, D8L
631E, 633E II, 637D, 637E, 657E, 769C, 769D, 771C, 771D, 988B, AD40, AD45, AE40, AE40 II, D8L
772, 938G II, 938H, 950G II, 950H, 962G II, 962H, 966G II, 972G II, D10R, D8L, D9N, D9R, IT38G II, IT38H, IT62G II, IT62H
330B L, 621H, 623H, 623K, 623K LRC, 627H, 637E, 777C, 777D, AD40, AE40, D10T, D10T2, D11T, D8R, D9N
D10N, D10R, D11N, D11R, D9N
D10N, D8L, D9L, D9N
D10N, D9L, D9N
3T0235
HOSE AS
D10
D10
3T0233
HOSE AS
D10
D10
4T0251
HOSE AS
D8L
D8L
4T0252
HOSE AS
D8L
D8L
7G5612
HOSE AS
D8L, D9L
D8L, D9L
3T1723
HOSE AS
D8L
D8L
9G7029
HOSE AS
D8L, D9L
D8L, D9L
D8L, D9N
D8L, D9N
D8L, D9N
3G7806
HOSE AS
D8L
D8L
D8L, D9N